vcds Particle Filter reset a4 2.0 2007

[boss151]

Hello. I have problem with reset dpf filtre in a4 2007. Dpf is changeg with new one and i need reset in ecu. I have VCDS, anyone knew how can i do that?
Best rgs. from Poland.

[cosmind]

search here Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Main_Page)

[boss151]

there in no info about reseting..:(

[8k65m]

Consider the fact the process of launching an emergency regeneration of soot filters on engines VAG group (1.4l/1.9l/2.0l R4 & 2.5l R5 PD / PPD-TDI).

Requires adapter VAG supporting CAN bus and the computer program VAG-COM.

Ignition on. The engine runs on the twentieth. Coolant temperature is not below 50 ? C
[Select]
[01 - Engine]
[Coding-II - 11]

Enter username to start the forced (emergency) regeneration particulate filter 21295.

[Do It!]
[Meas. Blocks - 08]
Select groups 070 and 075.
[Go!]
MVB 070.1: Status of regeneration (xxxxxxx1 = Normal Regeneration active, xxxxxx1x = Forced Regeneration active)
MVB 070.3: Regeneration Counter / Timer
MVB 075.1: temperature before the turbocharger
MVB 075.2: temperature before the particulate filter
MVB 075.3: Fill Factor particulate filter in%
MVB 075.4: The temperature after the particulate filter

Now you need to go and ride! The procedure takes about 15-20 minutes. At the same time control the fill factor, it should decrease.
[Done, Go Back]
[Close Controller, Go Back - 06]

[boss151]

But no regeneration!! Reseting!!

[cosmind]

why dont you disable it with ecusafe ?

[boss151]

i have new filter...and i must reset it.

[ipejasinovic]

After regeneration, counter will be reseted.

[boss151]

but when i have full loaded filter that can;t be burned..how can i reset filter when i remove it and with ecusafe make dpf off and i can do that by obd olny when dpf chck light is off(no errors) -errors are stored in eeprom mcu and i must use bdm...So there is a question ...It is posible to reset, with ory VCDS, dpf like in VAS?
Sorry for my english

[ipejasinovic]

Put back old dpf, force regeneration and then put new dpf.

[8k65m]

but when i have full loaded filter that can;t be burned..how can i reset filter when i remove it and with ecusafe make dpf off and i can do that by obd olny when dpf chck light is off(no errors) -errors are stored in eeprom mcu and i must use bdm...So there is a question ...It is posible to reset, with ory VCDS, dpf like in VAS?
Sorry for my english

See for example, file 03G-906-018-BKP.LBL
A012, 0, Regulation of the mass of soot
A012, 1, Engine Speed***8203;***8203;, (G28), Range of values ***8203;***8203;\ n Idling: 790 ... 810 rpm. \ Ntot load: 2800 ... 3200 rpm.
A012, 2, mass of soot
A012, 3, Need, regenerative function
A012, 4, the distance to and from the regeneration
A012, 5, After changing the particulate filter in this channel
A012, 6, adaptation prescribed to zero - the mass of soot and
A012, 7, the pressure drop in the particulate filter
A012, 8,
A012, 9, After changing the particulate filter soot from the old filter is removed and weighed
A012, 10, If this is not the mass of ash is calculated as follows:
A012, 11, takes an average fuel consumption (or is taken to be 7 l/100 km:
A012, 12 Massa ash = Distance (km) * Average fuel consumption (l) * ratio of carbon black (0.004569 g / L)

[boss151]

hmmmmm..:hmmmm2:

[djorgensen]

i have the same issue

there doesnt seem to be any info on how to set with VCDS a new DPF installation

I have a car with a new dpf filter and im unable to reset the dpf
yet when put in regen mode it is out of limp mode

duty cycle is set to 100.6% which just wont come down!


any ideas anyone?

thanks

[OMBRE]

Have you tried using VAS?