IAW 59F 5AF 5SF DECODER

[jokersat]

i recieve now my new tool fro IAW 59F 5AF 5SF DECODER from italia

hw is not same as kwp2000 it is deffirent

i test it on 59f m3 hw103 read write verry fast

i post all i have just for DK members

This interface operates on ECU 59F above and below 100 and 5SF, enables the riverginazione, scodifica the total becomes m3 m5 m7 m9, operates ECU mounted on a Ducati.
It does not require opening the unit, you can work in peace and quiet, just a simple clik to transform, scodificate completely, and erase mistakes riverginare DTC stored previously.
Very useful tool for tracking down those damaged units (default classic 2-cylinder) and carry out repair and resale "59F reclamation" of these highly sought ECU.

Models Supported / Supported Models:
59FM2
59FM3
59FM5
59FM7
59FM9
5AM DUCATI
5AFP3
5AFP4
59M
5SF

LIST OF FUNCTIONS SUPPORTED
DECODE 59F
SCODIFICA PARTIAL / TOTAL ABOVE HW-100 WITHOUT BOOT
SCODIFICA PARTIAL / TOTAL 100 HW UNDER NO BOOT
CHANGE SW M5 M3 5AF 5AM (Ducati) 100 ECC HW ABOVE WITHOUT BOOT
FLASH WRITE ABOVE HW 100 WITHOUT BOOT
5SF (HIGH POINT)
SCODIFICA PARTIAL BOOT MODE
READING FLASH BOOT MODE
WRITE BOOT FLASH MODE

EASY TO INSTALL AND CONNECT TO ECU WITH 4-WIRE
5SF (NEW 500 AND NEW FIESTA)
SCODIFICA PARTIAL BOOT MODE
READING FLASH BOOT MODE
WRITE BOOT FLASH MODE


@+

:manusign:

[haddia]

hello please can you tell me which interface you use this program

[fif]

which interface does work with this program?

[AMON]

Whwre did you bought it )

[Master01]

đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß...

[jokersat]

original interface from italia

see here IAW 59F (http://www.iaw59f.com/)

this interface is different
@+

[Master01]

đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß...

[naser]

original interface from italia

see here IAW 59F (http://www.iaw59f.com/)

this interface is different
@+

Mate is there a way we can see the interface from inside?:santaclaus:

[racin-snake]

not just interface but a pin out of the connector mate if its possible ?

maybe the wiring to the feed plus after ign and feed to switch
seems a bit of contesion over earthing too either earth to ecu body or to the pin on plug 1
all info appreciated

[jokersat]

i confirm for all DK

i test this interface on IAW59F M3 Today it work ok verry good no need open ecu

test Virgin = good tested on Car Punto work 100/100

test Immo Off = Good tested on Car Punto work 100/100

@+

[racin-snake]

can you show the connector wiring please ?

[paul_12345]

i confirm for all DK

i test this interface on IAW59F M3 Today it work ok verry good no need open ecu

test Virgin = good tested on Car Punto work 100/100

test Immo Off = Good tested on Car Punto work 100/100

@+


IAW59F M3 immo off???

[jokersat]

yes


immo off = tested

virgin = tested

@+

[jokersat]

can you show the connector wiring please ?


for ECU ? or what

@+

[dimitar]

for ECU ? or what

@+

everything you can post mate

[racin-snake]

i just need the actual connector to ecu plug wiring really
and what wire is switched ?


but i think someone else was asking for a photo of the both sides of the interface boards (i think )
but if you dont mind doing it mate it would help me out tremendously :top:

thanks ....

[jokersat]

i can do that my friend just for DK members

now i chek my interface


@+

:manusign:

confirmed = working not fake

[jokersat]

and screen shot software

:scarf2:

[racin-snake]

could you inclip the cover of the connector to ecu and confirm the wiring or post a close up picture ?
as the ecu wiring is my main concern
i need to see what wire go to what ecu pins

[jokersat]

4 wires

yellow + red + bleu + green

see on first post you can see this colors but note black = bleu

other is the same

@+

[racin-snake]

thanks again but what pins do these wire connect to on the ecu plug ?
as in pin 5=yellow ect

i know the colours but pin nos with wire colour are what im initially after

[ray978]

Centralina Aggiuntiva Potenza M Power M-Power (http://www.elettronicaceleste.com/prodotti_decoder45m.html)

This is not original? Soft almost equals.


hello friends .. I have this product for about 2 years old I am fine .. also the company is serious and does not charge money the files I need
Centralina Aggiuntiva Potenza M Power M-Power (http://www.elettronicaceleste.com/prodotti_decoder45m.html)

[elchip]

thanks again but what pins do these wire connect to on the ecu plug ?
as in pin 5=yellow ect

i know the colours but pin nos with wire colour are what im initially after

57808

Regard's

[elchip]

I looking for make similar tool ....
And today I test on one IAW59FM4 HW:103
I put it to classic boot via boot pin inside.
Readed with Galletto 1260 SW
Put it again in boot start write inside readed BIN file but I was interrupt writing by off POWER from ECU !
After that ECU was with bad FLASH inside !
I get ST10 SW and get classic KKL with FTDI232BL and L9637D in K-line stage homemade...
Boot ECU and start ST10 Flash program.
And surprise ;-) ST10 SW success conected and loaded bootloader - hehehehehe
I was convert BIN to HEX readed with Galletto needed for ST10 SW ( only work with HEX) and errase flash program and programmed ORI FILE readed with Galletto converted to HEX format....
After reset ECU :
TADAAAAAAAAAAAAAAA
ECU is back again LIVE :-)
:aetsch:

60429

If someone have good datashet about ECU pinout for HW under 100 and voltage level I will go FORWARD in research ...
Maybe we cant copy that tool but can find way to boot any IAW ECU without boot pin insude ;-)
Any good help and info are welcome...

[paul_12345]

can you upload the driver?? Thanks

[elchip]

can you upload the driver?? Thanks
Which driver ?
I all describe in post before.
Nothing special.
I just testing bootstrap handle via K-line message.
ST10FXXX have a lot of way to go to bootstrap mode ... ;-)

I expect a little help here from members or I will stop posting about ST10XXX my result's - sorry.

Regard's

[paul_12345]

Which driver ?
I all describe in post before.
Nothing special.
I just testing bootstrap handle via K-line message.
ST10FXXX have a lot of way to go to bootstrap mode ... ;-)

I expect a little help here from members or I will stop posting about ST10XXX my result's - sorry.

Regard's

I was referring to IAW 59F 5AF 5SF DECODER driver.

[elchip]

I was referring to IAW 59F 5AF 5SF DECODER driver.
So here is my work on it today ;-)
My ST10 flasher:
60502

My readed dump hex and extracted bin from hex ;-)
60503

ECU booted from ST10flasher SW.

My tool which I was project to be UNIBOX have IDC10 output connector and on it is:
one RX 3 or 5V level
one TX 3 or 5V level
K-line
RTS 3 or 5V level pullup
DTR 3 or 5V level pullup
On pcb is JUMPER for K-line enabling
Jumper for select 3 or 5V logic
Also is one DTR output open collector max 250 mA
It can work as motorola MCU programmer and many other SW support
One pin on IDC10 is for supply logic from target PCB if you need
And one is for supply 12V from output for K-line logic...

I was project and make cos I was need some UNITOOL on desktop...

Tested on ST10flasher software and work perfect ....
Maybe I will include later EEPROM programing for 24Cxx and 93Cxx serie who know...

Bye for now

Regard's

:pcguru:

[jokersat]

I was referring to IAW 59F 5AF 5SF DECODER driver.



here is drivers


@+

:manutop:

[paul_12345]

here is drivers


@+

:manutop:

Thanks, have you tested the transform m2,3,5,7??

[super jumbe]

Good post
jokersat could you give me the link were you bought it from please.

[racin-snake]

tried to buy the tool from iaw59f in italy

payment method and seller both unacceptable for me personally
moneygram and western union ..mmmm NOT FOR ME !

in fact both rude and obstructive attitude from this seller

i personally wont be buying from these guys if the attitude is this bad before purchase lol

anyone with an alternative except sellers on alibaba (as its the same seller)
please pm me details ...thanks

[paul_12345]

bit more expensive but there some on ebay

cgi.ebay.com/170559185705
cgi.ebay.com/170593822736

[racin-snake]

at least some come back from ebay not so much a difference in price about 40 euros
maybe worth it for the insurance of payment alone
being careful is a priority now its not just the chinese who are problematic i guess?

think i might hold out for now as seen reports of other units in production at the moment in eastern europe

watch this space if i find out more i will post

[Autronic]

Hi m8!!!!

For one that need software for reprogramming flash+E2 Marelli 59F 5AF HW up 100 with boot mode, the software is very good!!!
One software is for Eeprom (have two hidden buttons. read and write e2) and other for flash.
Work with KWP2000 interface.If need of help contacted me.

good work

Regards
Fab:pepsi::D

[domel45]

Hello, i used this tool( from IAW 59F (http://www.iaw59f.com)) to virgin ECU and I have to say it works great :)

[dottecu]

i need schematic for tool 59f ,5sf,5af.who can help me,i have old tool but not can cange configuration ,i can do only virgin

[racin-snake]

email sent by alex at 59f decoder site

info@iaw59***8203;f.com
To racin-snake
Hello,
I'm sorry that you think ill of me, but it is not a problem,
you use paypal and you can buy from another vendor that canguarantee and offer price equal to mine.
I think before you say that a seller is not serious or else ...... need toget information on my site and my nickname (Alex69)
This is why I prefer to lose customers like you,
also is the seller who says what method of payment you accept anddo not score to set the rules,
if you should buy our systems, otherwise you can go elsewhere.


"here is the response you get for not wanting to use another method of payment from the seller remembre"

"if this is what he thinks of his customers then would you buy from him ?????????"

info@iaw59***8203;f.com
To racin-snake
is not allowed to enter my email and my response aboutdigital-kaos,
if you violate this rule will be forced to initiate court proceedings for you.

You buy what you want, no problem for us,
each person with their money is free to buy as they see fit andwhere they want.

regards

Alex

"does the same apply to me alex ? showing your true colours now mate its good to see some folk dont like justified criticism ?"

too many rougue selers here trying to protect their stuff and no one knows whos who

or whether reports are accurate and im only trying to save some members from loosing out
hope this makes a point

[racin-snake]

you posted personal information

bet you thought id deleted my emails :roflmao:

totally wrong just shows your desperation
western union is not safe .............notorios for cheats using this payment method
have a look at the net mate


"only accept as payment:
moneybookers,
moneygramm,
Western Union
bank transfer"

all safe for the buyer ???????

How safe is western union or moneygram? | ~~~.co.uk (http://www.~~~.co.uk/threads/how_safe_is_western_union_or_moneygram)
read here and then tell me again ?




also are you denying you wrote any of the stuff you emailed that i have i posted ?

your indeed showing your serious intent :roflmao:

just keep posting your sales tat .....:rulez:

hope the mods see the reason your here not to help anyone but yourself ....

a leetcher with a sellers intent ............not so good, even threatening to bring court proccedings if i posted yor reply then post it yourself :stupid:

just wonder how many id's you have on DK multiple logins lol usual seller bump the stuff up with multiple logins umusing to say the least
i think the mods should have a look at this

[elchip]

you posted personal information

bet you thought id deleted my emails :roflmao:

totally wrong just shows your desperation
western union is not safe .............notorios for cheats using this payment method
have a look at the net mate


"only accept as payment:
moneybookers,
moneygramm,
Western Union
bank transfer"

all safe for the buyer ???????




also are you denying you wrote any of the stuff you emailed that i have i posted ?

your indeed showing your serious intent :roflmao:

just keep posting your sales tat .....:rulez:

hope the mods see the reason your here not to help anyone but yourself ....

a leetcher with a sellers intent ............not so good, even threatening to bring court proccedings if i posted yor reply then post it yourself :stupid:

just wonder how many id's you have on DK multiple logins lol usual seller bump the stuff up with multiple logins umusing to say the least
i think the mods should have a look at this

Hi racin-snake I am with you.
Read PM...

:canabis:

Regard's

[racin-snake]

thanks for that elchip
goes to show trying to sell and reap software and help then sell it as a third party back to the guys who he took it from in the first place .....mmmmmm

don't ya just love it another seller found out for spamming and trying to sell while playing at being helpful

totally wrong if your intent is to get sales you are on a loosing streak fortunately



is not allowed to advertise in this forum:reddy:.
If you want to advertise that you need to contact an administrator!

you do know the rules ...as this will show

go somewhere else and peddle the stuff
but don't go away angry
but by all means go away

[nany]

hello all members i have the same interface for decoding all iaw and i just add my opinion for this thread . using this to decoding and verginising your ecu iwa59f and 5sf ...........
it's a very good interface made in italy, very simple to use

[mimmo2011]

hello all members i have the same interface for decoding all iaw and i just add my opinion for this thread . using this to decoding and verginising your ecu iwa59f and 5sf ...........
it's a very good interface made in italy, very simple to use

Hello.
I bought the interface from Italy www.Ecumax.it (http://www.ecumax.it) payament paypal

[racin-snake]

:wink:many thanks mimmo2011 ile see about this tomorow
looks like it can do the job
hopefully it can be with me soon

as for remembre or alex or whatever
i removed nothing
you broke the :rulez:

and i do not care to carry on with this any more you see it does not matter about the actions you take you are clearly clutching at straws
thanks for your input its been a revelation
and goodbye

and i can now buy from a source with the payment method i choose (which is safe )

in your own email you say i should do this
ile report on my findings with the tool from here www.Ecumax.it (http://www.ecumax.it/)
gives another option other than one supplier ......cool its even the same price to buy so no loss :listen:

[Remembre]

this is very good vendors:roflmao:

[racin-snake]

ile be backed up to safely spend my money though wont i ?

and ile tell these guys you said this they'll appreciate your condoning there tool
and they spent more than 5 euro on there site too its very well laid out easy to navigate


this is very good vendors:roflmao:


i see you can criticise but say everything is not the truth when it comes to you

ah well if you can afford to loose sales and be pathetic too then so be it
again i say goodbye and don't slam the door on the way out:roflmao:

[racin-snake]

OK you stay in your bubble mate :laugh:.............. most have read the emails you sent to me thanks
im cool with that

and a gentleman ? if people do have a look at your lengthy and numerous posts i think they will see the opposite :roflmao:

off to buy from the vendor you recommended thanks for the help its appreciated and once again goodbye :wavey:

[racin-snake]

11 posts since 2010 most of them protecting your sales ????
and you say a member like me lol

the only thing you have gotten right is a poor estimate of my age lol

mmmm


yes my freind your a bit of an oddity
hope you do well in sales now :proud:

goodnight :roflmao:

[Remembre]

good night racing-snake

[racin-snake]

and ?
nowt more to add here ?
nice screen shots
apart from that please elaborate is this the screenshots for my new tool perhaps ?


if that is ile see those when i buy it but nice to see you put your competition up for scrutiny
looks like better software too
thanks again
you are a true gent lol

[keygargoil]

Hi m8!!!!

For one that need software for reprogramming flash+E2 Marelli 59F 5AF HW up 100 with boot mode, the software is very good!!!
One software is for Eeprom (have two hidden buttons. read and write e2) and other for flash.
Work with KWP2000 interface.If need of help contacted me.

good work

Regards
Fab:pepsi::D

i have a corsa d ecu how can i read it its like the fiat ecu,s its a 0 261 208 940
gm AX

any suggestions please i need to immo off as the keys are programmed but wont start

[yellowstilo]

good night racing-snake

please correct "tunig" in the second screenshot, that doesn't look very professional....

[racin-snake]

the producer has made the software as per the screenshot,
better left as the original source

has the producer put my avatar in the screen shot ? ...............thats naughty lol

i wonder if i should have asked for a discount then ?
anyhoo ile let you know how it goes when it lands ...thanks again ...


professional and some should not be mentioned in the same sentence as you might have noticed
and to some all the lies they tell are the truth ......mmmmm

[Remembre]

sometimes good for studying

[racin-snake]

cloning or retro engineering would be the correct term ?
and copying software too perhaps

good deal 295 euro and 10 euro postage
insured and paid with paypall
safe secure cheaper and looks better than the iaw59 unit
ime extremely happy ......
and will post quality screen shots when it arrives :top:

[Remembre]

cloning or retro engineering would be the correct term ?
and copying software too perhaps

good deal 295 euro and 10 euro postage
insured and paid with paypall
safe secure cheaper and looks better than the iaw59 unit
ime extremely happy ......
and will post quality screen shots when it arrives :top:
good :top::devil:

[racin-snake]

very good in fact.....
nice site too don't you think ?
i knew there would be a retailer who could do pay pall and not just insecure money transfer and western union
so looks like a good deal for me :top:
same price or less and safe transfer of money and insured post "safe as houses"
so yea remembre its good deal................a bloody good deal

one not offered by less serious vendors though ?

seriously though this thread has had 2500 extra hits since you posted my personal details ..ok

then you ask people to buy from you ..............and what will happen to their details if they complain ?

might be uses for more subversive purposes ?

your colours are not so bright now remembre ?
i think in this instance you could have saved sales by just being quiet
now 2500 potential customers are now not so trusting or running in the opposite direction
but one good thing youve added nine more post to your grand total of posts to 15 and 2 downloads in over a year ............................so not all bad ? :laugh:

and considering your double standards when alientech posted his bit of spam on here you were quick to call him an advertiser and show his ip address ect ...not so kosher and just dirty tactics
but only to be expected from a seller trying to protect his sales

not a forum member but a forum letcher ..remember most will have read your previos posts by now and came to the same conclusion ?



:roflmao:

[racin-snake]

if i do get STUMPED then i can use pay pall to collect ...thanks

i have put the list of all the payment methods on a previous post if you have a look here ?


you posted personal information

bet you thought id deleted my emails :roflmao:

totally wrong just shows your desperation
western union is not safe .............notorios for cheats using this payment method
have a look at the net mate


"only accept as payment:
moneybookers,
moneygramm,
Western Union
bank transfer"

all safe for the buyer ???????

How safe is western union or moneygram? | ~~~.co.uk (http://www.~~~.co.uk/threads/how_safe_is_western_union_or_moneygram)
read here and then tell me again ?




also are you denying you wrote any of the stuff you emailed that i have i posted ?

your indeed showing your serious intent :roflmao:

just keep posting your sales tat .....:rulez:

hope the mods see the reason your here not to help anyone but yourself ....

a leetcher with a sellers intent ............not so good, even threatening to bring court proccedings if i posted yor reply then post it yourself :stupid:

just wonder how many id's you have on DK multiple logins lol usual seller bump the stuff up with multiple logins umusing to say the least
i think the mods should have a look at this



third . i am neither a seller or associated with any seller of this tool
but in fact you are the vendor of a tool
so i have broken no rules posting links
as i am showing alternatives to a IMHO a better option to your effort
and lastly ...if your assumption is correct about maturity then you previously posted ime over twenty five which i concur
so therefore i am in fact mature
if you could possibly just look at the previous attempts of yours to discredit any of my findings then you will see i have in fact nothing to hide i sell nothing and condone no products or sellers on this forum
i provide links to help other members to make a SAFE and EDUCATED way of buying tools they need
emphasis on the word help which i think your posts go to show all 16 now that your here to help yourself

i also don't see you moaning about the links others have posted for your tool ?
like this
[QUOTE]who posted the link where you have purchased is the same seller, the rule prohibits advertising on the forum,
you should first arrange to monitor and moderate the forum, what you have done if not against me that I have responded and entered an email confirming that you have said some of the false quote because you have only two methods of payment that I ask
and the other 2 like Moneybookers and bank transfers are not you entered them.[QUOTE]

bit more double standard ...and in my opinion shows how utterly FAIR you are
you are here to monitor sales and glean (leech) information to line your pockets arnt you ?

you should look back and see the posts i have written do not defame but in fact show your attitude is as exactly as i stated obstructive and rude

facts will speak for themselves ...as you know and your desperation shows ..i thank you for being so candid and now others will see you as the way they should IMHO

so once again i say
dont go away angry ............but please feel free to just go .....

[racin-snake]

I tried to give you help with some of my statements .........., I help you and you have not understood,
Sometimes you have to read between the line.
But you do not understand what I was saying.
I understand from just a few days. LOL

that would be a total change in character

YOU ...HELP? they shouldn't be in the same sentence as far as you are concerned

your attitude speaks volumes your rebuttals are as pathetic as your lack of answers
and the TRUTH you have a distinct blockage in that department
you wouldn't know the truth if you woke up beside it lol

anyhoo i care not a jot about your tool and will post the screen shots and so on if and when i choose thanks
another prerogative i have other than buy using crude and untrustworthy payment methods
so i bid you goodbye and hope your sales are plentiful :roflmao:

and next time you post someones personal info ..make sure you pick the target better and get your t's crossed and i's dotted

as your looking shaky and the people on the buying end can see ...your not kosher my friend..........

[cardoctor]

http://www.digital-kaos.co.uk/forums/f178/magneti-marelli-iaw-08p-1c-209338/

anyone know about it..

[racin-snake]

:roflmao: Time is on our side:top:

funnily its .....NOT .... there are different places making the same stuff at lower prices as i type and even funnier they are gonna flood your dwindling market soon with your show of uncertainty here you know i am correct :roflmao:
i wonder how many sales you lose now ?

welcome to the real world my freind


3200 hits all customers you might have had
good luck mate you will need it :top:

i have nothing to sell so time is indeed on my side ....

your true colurs have been shown you know it and I KNOW it

[Remembre]

long time friend LOL

[racin-snake]

long time friend LOL

short for me though i dont have stock to shift so no worries here

but i think instead of typing a load of shit you could redeem yourself by "HELPING SOMEONE "
instead of trying to scratch a killing selling your crap

anyway ime not going anywhere :proud:

ile still be here trying to help and enjoying the thought ime part of a community and that i can help those who are purchasing the stuff on line to stay safe and to avoid being ripped off
while you my freind try to save your self by posting twaddle in attempt to sell these people your stuff
soon a seller will undercut your price by a good deal you wil be sunk

so its a long time looking to sell stuff for you :banghead:
for me ile be comfortable knowing another DK seller has met his end
i have a lot of time so please don't mention it again as i do not care for your rubbish

desperate man with nothing to say .....so amusing :hahaha:

[racin-snake]

now also become abusive? I'm not abusive, but you just correct terms used in public and this is bad publicity.
Did you know that we have already helped many people and yet we are doing by providing some software.

However I give when people feel and begin to be affected ...... ...... scurrilous
is a sign of mental collapse

eh ?

abusive ? don't think so ......desperation and mental collapse on your behalf I think ?

I am never abusive ...more factual than your self ime sure

bad publicity is your fault mate . you should have not posted my details to inflame the situation and show your true colours

your loss is your fault not mine your own doing ...

[racin-snake]

repeating the same phrases.

you have no other arguments,
I think I speak with a person with many arguments and not with a very limited always to write the same sentences,
this is mental breakdown,
I prefer not to respond to this,
Meanwhile, I demonstrated that you are fake and just write what you want to discredit people,

after my speech you have admitted your guilt of not having told the whole truth and inserting some of what we wrote, obviously you're limited like you miss many things.
However, you are a moderator and in these cases, you grow a brain, you are very limited for my liking and I prefer to leave it alone.
Good luck, and I'll read your comments about the operation of which will send another vendor, if other people have problems I just hope the publicity will contact you as you have done to a person who is present in this forum and that is hidden,
picks in this forum and sells on his website ........
wake up and see the entire website racin-snake.
Ask if you can sell engi76 59F, he will certainly respond as they are the same person.

bye bye small earthenware

my guilt ???? an admission ???


mmmmmmm mental breakdown don't think so you have the mental block :roflmao:
your delusional off your rocker :stupid:
please go away save yourself some more embarrassment

as your starting to get a bit obnoxious with the personal remarks further showing your desperation and further showing your a serious seller and a gentleman as you claim lol

i see the website all to well and seem to know a bit more than you give credit for lol

in my opinion i think your just making noise

and you know what they say about empty vessels

ile spell it out for you


"empty vessels make more noise"

[Remembre]

hello friend "racin-snake",
have you tried the interface?

[racin-snake]

i also see you have dropped the price of your tool on your site quite considerably



POST EDITED TO RECANT INFORMATION

[racin-snake]

WOW I RECANT THIS WHOLE POST ..

[racin-snake]

just an update ...i have a friend who tried to buy from you via credit card
and iaw59f wanted credit card details via email ????

hows that secure ..
i don't know how you do business but that's just not on mate unsecured asking for credit card details via email
money bookers and western union

wow i wonder is this for real ?
i recant everything i said about trust alex ...i wouldn't deal with your company not in a million years

so many ways to get screwed OUT OF YOUR MONEY

[racin-snake]

lol your asking a person to put their credid card details in an email ?
are you out of your mind ?

man i thought you had improved but your going backwards
worse of all i recommended the poor guy to you got me a right red face

wow i wonder what next from you lol

[racin-snake]

yea for a seller your real good mate
your an embarrassment
really you think someone's gonna buy from you with this mickey mouse set up lol
your a joke pall
as for reading ?

nice to see your customer liaison is working its usual charm ?
saying your customers cant read lol
who wrote your posts ?
barely legible so i can imagine your emails are far worse

in fact they are see for yourself


Perhaps you misread.


I send my visa number,

the person who buys goes into his bank and send payment by credit card.

To me, your friend must not send any information,
only has to pay into its bank.

:laugh::laugh::laugh:

we believe that your friends read bad
and you have misinterpreted our words.

Ask a customer his credit card number is not crazy ..... is stupid and thieves,
I am neither stupid nor thieves!!;)


really please do not buy from this guy he is a joke !!!!!!

ile tell you what ile send my bank details you send 230 euro to my account ??

thats what your asking mate the guy dont know you from adam ??

i hope he goes away before he makes any more of a fool of himself
think mickey mouse has an alex watch

[yellowstilo]

guys... how long will this post last ??
Maybe it is better to continue in private.....

[racin-snake]

whys that ?

guys gleaning some sales with other posts why not see his full deal ?
if you dont like it just look somewhere else ?
there's hundreds of other posts to see

[paul_12345]

I can understand not wanting to accept paypal they are scum for sellers.

But western union etc your looking at 10% buyer fees, and no protection for buyers.

Simple solution accept nochex or google checkout no easy scams as paypal 'disputes' will cost seller 3% fees so increase price 10% buyer doesn't loose out due to WU fees, and you have 7% more money which should cover the few potential chargeback loses.

Could probably even sell for 280E make more which will easily cover the potential scams

Everyone wins

[racin-snake]

that's good for the rest of Europe then save them getting ripped off

its not just language that's the problem believe me your attitude and your shifty dealings are more than probably due to you and paypall having a disagreement ?

but most of all it will keep the DK members safe from dodgy sellers like yourself
who are free to glean advertisement and post link to DK to show the tools appreciation by buyer ect
i hazard you wont be using that link to show your customers now ?
anyhow its not a great loss that you are now going you are quite happy to send pm messages to me off seller ..saying they are untrustworthy
when i do the same to you you retaliate by posting my personal details
imagine if i had been dumb enough to send my bank details :roflmao:

but again language will get the blame for that too?

go away fool and sell your stuff to the Italians

goodbye and best regards forum leecher :laugh:
and ile pass on looking at your site
it doesn't interest me in the slightest i think if its as bad as the site you sell from id be better off not wasting my time

[racin-snake]

traaaaa :rofl:

nice to see you go :top:

[Remembre]

I do not go away,
but useless to fight with the deficiency

maybe you're burnt to ccsit autoreliable and now
believe that all sellers can fool you or those who believe in you.

[racin-snake]

I do not go away,
but useless to fight with the deficiency

maybe you're burnt to ccsit autoreliable and now
believe that all sellers can fool you or those who believe in you.

eh ?

what the hell was that ?
anyhoo remembre your either daft or a nieve boy ?:

i think you need to go look at a way to sell properly as your really poor at it
makes you look amateur and then you can realise its not the tool

"ITS YOU " your the problem

[Remembre]

but what do you use the translator to write in English?

[elchip]

but what do you use the translator to write in English?

He not translate ;-)

:canabis:

[racin-snake]

i do not have to translate i speak and write English


i see you have a deficiency ...right between your ears` is where it should be lol

your ego has got you into something that you regret you should think before posting any ones personal details
that is just wrong
and that is how i know your not trustworthy
your ego is far to big for your intelligence my friend

[elecautocr]

hi members:

Do you know if it is possible to eliminate immobilizer (Total) for Ducati Bike ST4S IAW59M with the 59F Decoder tool ?? OR

Is it possible to read/write Ducati IAW59M with MPPS ??

Thanks

[maglaras]

hello to all
i have the IAW decoding
when i take it it work ok
i fix 5 or 6 ecu
now the tool did not work when i tray to make immo off or virgine the tool stop and can not do anything
i chek usb cable i chek power 12v'i tske the tool to another pc
i take ecu of a car that work ok and i tray to make it virgine and now the car did not start
please if you can help me
i tray to make boot mode in kw plus but i can not make ot work
only i can ride it with kess on the car but i can not rite it
i tray to rite whitr galleto mpps nothing
is the ecu dend?????????????????

thank you

[maglaras]

hello to all
i have the IAW decoding
when i take it it work ok
i fix 5 or 6 ecu
now the tool did not work when i tray to make immo off or virgine the tool stop and can not do anything
i chek usb cable i chek power 12v'i tske the tool to another pc
i take ecu of a car that work ok to chek the tool:stoned::stoned: and i tray to make it virgine and now the car did not start
please if you can help me
i tray to make boot mode in kw plus but i can not make ot work
only i can ride it with kess on the car but i can not rite it
i tray to rite whitr galleto mpps nothing
is the ecu dend?????????????????

thank you
:stoned::stoned::stoned::stoned:

[maglaras]

if you ever have problem whit this tool
you must cut the cable that give power to the tool
and fix it or give it power when you cut the cable
***953;n the socekt
the tool work again perfect

[rsibiza]

When i read an IAW5AMHW610 from Ducati Monster S2R 1000,can i do immo off by just hit immo off?

In sw decoder is wrote only Ducati S4R? but still same HW610,or load ori file and write back immooff file from some immo remove sw?

[Metin]

good night racing-snake


hi

from where can download v5.5 ?
thanks

regards
metin

[daviee]

i recieve now my new tool fro IAW 59F 5AF 5SF DECODER from italia

hw is not same as kwp2000 it is deffirent

i test it on 59f m3 hw103 read write verry fast

i post all i have just for DK members

This interface operates on ECU 59F above and below 100 and 5SF, enables the riverginazione, scodifica the total becomes m3 m5 m7 m9, operates ECU mounted on a Ducati.
It does not require opening the unit, you can work in peace and quiet, just a simple clik to transform, scodificate completely, and erase mistakes riverginare DTC stored previously.
Very useful tool for tracking down those damaged units (default classic 2-cylinder) and carry out repair and resale "59F reclamation" of these highly sought ECU.

Models Supported / Supported Models:
59FM2
59FM3
59FM5
59FM7
59FM9
5AM DUCATI
5AFP3
5AFP4
59M
5SF

LIST OF FUNCTIONS SUPPORTED
DECODE 59F
SCODIFICA PARTIAL / TOTAL ABOVE HW-100 WITHOUT BOOT
SCODIFICA PARTIAL / TOTAL 100 HW UNDER NO BOOT
CHANGE SW M5 M3 5AF 5AM (Ducati) 100 ECC HW ABOVE WITHOUT BOOT
FLASH WRITE ABOVE HW 100 WITHOUT BOOT
5SF (HIGH POINT)
SCODIFICA PARTIAL BOOT MODE
READING FLASH BOOT MODE
WRITE BOOT FLASH MODE

EASY TO INSTALL AND CONNECT TO ECU WITH 4-WIRE
5SF (NEW 500 AND NEW FIESTA)
SCODIFICA PARTIAL BOOT MODE
READING FLASH BOOT MODE
WRITE BOOT FLASH MODE


@+

:manusign:

Hello!

Can you give me the contact of author of this tool?
On the webside can't find them :-(

Thank you.

[dj_piex]

Iaw59F ;)
(http://www.iaw59f.com)

[alpha-music]

i only can tell, i also bought this tool from him..

and i send money normal via bank transfer...

2 days l8ter i had it...

why dont trust ?

[racin-snake]

i got mine a couple of weeks ago paid by paypall
came in 3 days
did four ecus so far with no problems except software language :hmmmm:that is ..
but its good you can pay via paypall now for this tool

[automotive]

prejudice anyone has the hex file of the pic I can help you with the hardware but I have the hex file contained in the PIC16F876

[automotive]

i can do that my friend just for DK members

now i chek my interface


@+

:manusign:

confirmed = working not fake


prejudice anyone has the hex file of the pic I can help you with the hardware but I have the hex file contained in the PIC16F876

[Remembre]

new software to decode 59f,
but it needs a code to activate it.

the new sw is able to do immooff ECU
less than 100, excluding 002 003,
It is also able to read and write files

[automotive]

I can delete to activate the software if you help me with the hex file of the pic 16F876

[Remembre]

I can delete to activate the software if you help me with the hex file of the pic 16F876

is cripted

[automotive]

is cripted

yes Asprotect ..........

[automotive]

Aspack v2.12

[racin-snake]

so where is this code needed to update if you have bought the hardware from you ?

please give an explanation thanks

[orucreis]

hi
i have 59f decoder
but this is broken
i need ft232r ept files with Mprog
thanks

[Remembre]

hi
i have 59f decoder
but this is broken
i need ft232r ept files with Mprog
thanks

problem resolved!

[automotive]

so where is this code needed to update if you have bought the hardware from you ?

please give an explanation thanks

contact the seller

[racin-snake]

remembre is the seller the tool was bought from mate :top:

[benzerrouki]

hello every one pls need virgine dump for iaw5a5p thank baddy

[nemena]

Dear All,

Could someone virginize this file for me with this decoder please?
This is HW004!! 95080 read by needles!
Thank you in advance!
Peter

[i_shot_the_sheriff]

Hello,

I think that celeste tuning's tool can do many more ecus! Like the 5NF and the 4F family,,, also the Multijet (new ones)!!

What do you think?

[felix_fetche]

try this.
how you acces eeprom, OBD or by removing plastic?

[felix_fetche]

i was meaning K-Line by connectror, not OBD, ecusses.
also try this diferent solution of virginization.

[yellowstilo]

Hello,

I think that celeste tuning's tool can do many more ecus! Like the 5NF and the 4F family,,, also the Multijet (new ones)!!

What do you think?

the Celeste 45M decoder is no longer available - their new tool IDEC 59 doesn't support the 5NF (and 4F?) ecu...

[yellowstilo]

I can delete to activate the software if you help me with the hex file of the pic 16F876

how can the pic be read? I assume it is protected?
It would be great f you could deactivate the password for this soft !

[mastaflex]

does someone tried or succeed in virgin IAW5SF3 grande punto in boot mode.

software always tell that ECU did not respond :(

[ray978]

Centralina Aggiuntiva Potenza M Power M-Power (http://www.elettronicaceleste.com/prodotti_decoder45m.html)

This is not original? Soft almost equals.

that is longer than the one who bought jokersat ..
also works on bosch ibid mjtd etc. ..

[ray978]

someone speaks of a great good of this CDC-Marelli 59Fxx.

what do you think?

[pfeff-cool]

new software to decode 59f,
but it needs a code to activate it.

the new sw is able to do immooff ECU
less than 100, excluding 002 003,
It is also able to read and write files

How can activate this software?

[Metin]

does someone tried or succeed in virgin IAW5SF3 grande punto in boot mode.

software always tell that ECU did not respond :(

yes, with box hw v2

[ankara06]

no need IAW decoders for decode 59F,5AF,5SF,5NF series

[AMON]

so, what do you need ?

[mcgustoo]

Do you have hardware schematic and HEX for iaw decoder???

[Remembre]

This software works only on ECU
Hw to Top 100
can read and write files:wink:

[maglaras]

ok the software but what hardware work this software??????????????????

[oep]

Am intrested in project - pls conntact me if you have..

[yellowstilo]

does anyone have sofwareversion v5.5 for the Italian IAW59 decoder?
I hope someone will upload it, thanks a lot !
It looks like this:

[Remembre]

ok the software but what hardware work this software??????????????????

yes no problem:top:

[Remembre]

for those who want to use this interface on 5SF and can not get it to work,
you must insert a resistor between the line k 1kohm the positive 12v.
then follow the patterns of 2 resistors and see which works without problems

[yellowstilo]

for those who want to use this interface on 5SF and can not get it to work,
you must insert a resistor between the line k 1kohm the positive 12v.
then follow the patterns of 2 resistors and see which works without problems

could you please explain this more detailed?
Normally a 510 ohm resistor is connected between 12v and K-line which is pulled to ground with a transistor.
Do you mean i would have to put a 1 Kohm resistor parrallel to the existing 510 ohm resistor or instead of?

thank you,
yellowstilo

[maki]

does anyone have sofwareversion v5.5 for the Italian IAW59 decoder?
I hope someone will upload it, thanks a lot !
It looks like this:

I'm think is it what you need.

[yellowstilo]

I'm think is it what you need.

thanks Maki, unfortunately a activation code is needed which i don't have...
does anyone have a workaround for this software?

[spiridonas]

Hi guys i need to decode a ecu iaw59f.m7 hw004
i have two tools FGTech 2012 galletto v2
and galletto v1260.

I tried with FGTech 2012 galletto v2 and i read succes flash file, but for decode must to read eeprom, i can with my tools?
Many thanks

[keygargoil]

Dear All,

Could someone virginize this file for me with this decoder please?
This is HW004!! 95080 read by needles!
Thank you in advance!
Peter

hi what tool did you read it with and you read it by needles wo9w

[keygargoil]

i am looking at reading a 59f ecu to virginise is it easy to read with kwp i take it i will need to read it on the bench or can it be done by obd i also have a stilo i cant remember exactly what series it is but i would like to read this to the flash seems to be corrupt it runs rough as a dog

[keygargoil]

is it the st10 that needs to be virgined to reprogramme the ecu or eeprom

[Cdoc]

hi
i need immooff for ducati DS1000 in iaw5am hw610
thanks fab

[Cdoc]

hi
i m sorry i read wih AVDI
thanks fab

[spiridonas]

Hi guys i want to buy the IAW 59F DECODER i paid two times the iaw59f.com but after 10 min i receive full refunds with this comment:
Additional comments: out of stock

Please informe for other seller with this tools.
Many thanks in advance

[Nigola]

Hi guys i want to buy the IAW 59F DECODER i paid two times the iaw59f.com but after 10 min i receive full refunds with this comment:
Additional comments: out of stock

Please informe for other seller with this tools.
Many thanks in advance


Have you tried to buy one without connector?

I 2 months ago I bought one without connector, because the one with the connector was not available.

Nigola ...

[spiridonas]

Hi i tried to buy one without connector but there is no text field for quantity statement.
With connector there is text field for quantity statement but is not available.

[spiridonas]

Hi i found this seller :
DECODE IAW 59F - 5SF - Ecuracing.eu (http://ecuracing.eu/product.php?id_product=17)

Please know anything about this seller or product ?

Many thanks

[ALVARES]

ecuracing no good seller.
sell only the bad old clones defective. And when you ask for help in operation do not respond. When you find something you can throw fault because it is not available.

[mimmo2011]

ecuracing no good seller.
sell only the bad old clones defective. And when you ask for help in operation do not respond. When you find something you can throw fault because it is not available.

I bought the decode 59f, so good.
I bought other products and I had no problem

[Nigola]

SCODIFICA 59F 5SF MARELLI E CAMBIO SW SENZA BOOT | eBay (http://www.ebay.it/itm/SCODIFICA-59F-5SF-MARELLI-E-CAMBIO-SW-SENZA-BOOT-/170734801644?pt=Ricambi_automobili&hash=item27c09652ec)

[gigitalkaos]

Hi i wanna buy project iaw decoder from site indigopcb.org i have idea if we buy together its will be cheaper...

[mimmo2011]

Anyone tested?

have you tried this?

[mimmo2011]

Hi i wanna buy project iaw decoder from site indigopcb.org i have idea if we buy together its will be cheaper...

here are selling projects

Hardware, software for programming ecu and chip tunning car (http://www.car-prog.eu/)

[Master01]

đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß... (http://autodijagnostika.biz/hr/dekoderi-i-emulatori/iaw-59f-decoder-v5.5-hw3-magneti-marelli.html)

[mimmo2011]

have you tried this?


no,
I have not tried

[yellowstilo]

Dekoderi i Emulatori :: IAW 59F Decoder V5.5 HW3 - Magneti Marelli - www.autodijagnostika.biz :: auto dijagnostika, dijagnostike, (http://autodijagnostika.biz/hr/dekoderi-i-emulatori/iaw-59f-decoder-v5.5-hw3-magneti-marelli.html)

Can someone valid email address?

Don't buy this tool - it is very badly made , soldering much worse than Chinese tools and very unprofessional finishing.
Bad customer service - took me 2 months to receive a non-working replacement tool , had to rework the pcb before it got functional.
Communication is next to zero - seller waits till you're really ****ed up after lots of non-replied messages before sending a reply....
Don't waist your money here - the Italian IAW59F decoder is way better than this crappy tool !

[stevan]

Anyone tested?


I have it,also i have ver.5.0 first one from them, and found some bug's on some ecu on 5.0ver.
Than i see ver.5.5 is out with fixed bugs and i order it.
New 5.5 HW come defective,PC not see HW and not work.
Sended back and after several days i get one that work.
5.5 ver. installed and new hardware not work at all,PC see device but can;t connect on any comp.
After i have call them again i get info that some .dll is problem.
I have try on 6 laptop and 2 PC all same.
Reinstalled fresh XP on one Laptop and again not ok.
I have install old 5.0 ver and work again like my first device.
So now i have 2 pcs of IAW decoder ver.5.0 with some bug's.
I have no time to make experiment's with .dll to make 5.5 to work.
If someone have solution please explain how.

[yellowstilo]

i see i'm not the only one who received a shitty tool from Autodiagnostica / Biz team - i guess there must be lost of buyers with the same problems.....
I have opened my (second) tool and after i recovered from the shock regarding the terrible build quality i decided to rebuild the pcb.
I added a 9 pins D connector instead of the fixed wires, a usb socket instead of the fixed + glued cable, a switch instead of the shorting wire , resoldered lots of components and rewired the floating DIL pic which should have been a SOIC type according to the PCB design.
Now the tool seems to function rather stable with V5.5 , before my rework of the PCB the tool was often not recognised by my laptop.
So when BizTeam does not solve your problem properly (which will be difficult with such a horrible build quality) you might give it a try.....

[Master01]

Don't buy this tool - it is very badly made , soldering much worse than Chinese tools and very unprofessional finishing.
Bad customer service - took me 2 months to receive a non-working replacement tool , had to rework the pcb before it got functional.
Communication is next to zero - seller waits till you're really ****ed up after lots of non-replied messages before sending a reply....
Don't waist your money here - the Italian IAW59F decoder is way better than this crappy tool !

đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß...

[yellowstilo]

the seller talks about his "factory" but i think these tools are actually made on his kitchen table considering how it's put together....

[stevan]

i see i'm not the only one who received a shitty tool from Autodiagnostica / Biz team - i guess there must be lost of buyers with the same problems.....
I have opened my (second) tool and after i recovered from the shock regarding the terrible build quality i decided to rebuild the pcb.
I added a 9 pins D connector instead of the fixed wires, a usb socket instead of the fixed + glued cable, a switch instead of the shorting wire , resoldered lots of components and rewired the floating DIL pic which should have been a SOIC type according to the PCB design.
Now the tool seems to function rather stable with V5.5 , before my rework of the PCB the tool was often not recognised by my laptop.
So when BizTeam does not solve your problem properly (which will be difficult with such a horrible build quality) you might give it a try.....

You got it work with 5.5 ver.?

[666_devil]

OK.

So what is the best place to buy decoder?!

If I understand well the guy from "www.Iaw59F.com" (http://www.iaw59f.com) sells good stuff and all rest of them are too expensive or selling rubbish?

I was really interested in that "www.autodijagnostika.biz" (http://autodijagnostika.biz/) decoder, it was better price but if lot of have bad experience I will search somewhere else.

Thank you in forwards for your advices, because I have to buy one next week.

[yellowstilo]

don't buy the Autodiajnostika.biz tool, you will regret it !!!
the IAW59F.com tool is way better built , it also works with v. 5.5 but only for hw versions above 100.
for hw versions under 100 you can use version 2 or 3.

[666_devil]

don't buy the Autodiajnostika.biz tool, you will regret it !!!
the IAW59F.com tool is way better built , it also works with v. 5.5 but only for hw versions above 100.
for hw versions under 100 you can use version 2 or 3.
Do you have the tool from him. You did the tests? You got the appropriate software with tool?

[yellowstilo]

yes, i bought this Autodijagnostika tool - returned the first one and received a second none-working tool .
After i decided i would not return it again i opened the resin filled box and was shocked by the horrible build quality.
I also have a IAW 59F.com tool for comparing, this is way better built and it does what it should.
software was sent as a download link .

[666_devil]

yes, i bought this Autodijagnostika tool - returned the first one and received a second none-working tool .
After i decided i would not return it again i opened the resin filled box and was shocked by the horrible build quality.
I also have a IAW 59F.com tool for comparing, this is way better built and it does what it should.
software was sent as a download link .

Thanks man, I bought one 4 years ago and I paid it 600?, but last month it was stolen from my car. So now I need a new one, and I can not find the guy on ebay from Italy where I bought it. I will buy IAW 59F.com decoder next week and I will share my results.

[jaelgti]

It has the decode?
that time he has taken?
I am planning to buy, any suggestions?
thanks

[yellowstilo]

i have the IAW59F.com tool, works o.k. and fast....
you will need sw versions 2 or 3 for hw under 100, for hw above 100 you can use v2 up to v 5.5.

[jaelgti]

That price?
Thanks for answering.

[yellowstilo]

200 euro without 59F connector, 215 euro with connector plus shipping costs (don't know anymore how much i paid , will depend on your location)

[jaelgti]

I can only say it is a great tool.
thanks for helping.

[koyot]

what do you think about this
http://www.nasratech.com/#

[yellowstilo]

it looks promising but i did not find any confirmation that is really does what it promises.....
We need some independant buyers who can confirm it works as it should and who have positive support experience - i'm afraid this looks better than it really is.....
any volunteers ?

[didi_du_93000]

what do you think about this
Nasratech (http://www.nasratech.com/#)

Full working!!!!
Best solution for small price.
Working great on OPEL, FIAT groupe and FORD.
You can go to buy without problem.
If you need video or picture i can do it.

[didi_du_93000]

The best technical service on skype and email!!!
No more wait to 1 hours!!!

[kerekt]

hi

i have the same tool but dont have v55 can u help with it ?


i have the IAW59F.com tool, works o.k. and fast....
you will need sw versions 2 or 3 for hw under 100, for hw above 100 you can use v2 up to v 5.5.

[racin-snake]

do a forum search for nasratech you will maybe think twice at buying anything they sell

a legion of people on DK bought it and were completely disgusted with what they got

http://www.digital-kaos.co.uk/forums/f155/vauxhall-opel-pincode-reader-has-been-released-119593/index13.html#post1214731

this thread her along with others Caveat emptor is the words !!!!

[mimmo2011]

I bought qi: DECODE 59F - 5SF SENZA BOOT - ECUTRONICK (http://ecutronick.com/it/home/59-decode-59f-5sf-senza-boot.html) works well

[vanya86]

don't buy the Autodiajnostika.biz tool, you will regret it !!!
the IAW59F.com tool is way better built , it also works with v. 5.5 but only for hw versions above 100.
for hw versions under 100 you can use version 2 or 3.



m8 what is this???

[yellowstilo]

Now you really convinced me you are a unreliable and lying "company"......
In another post you pretend to have bought from this "company" without problem while you are actually the seller from Autodiagnostika.biz....
I'm not the only one who bought your crappy IAW 59F decoder, unfortunately other DK members made the same mistake....
So please stop lying about sending me 3 decoders and don't pretend you are a customer instead of the seller.....

"yes, i bought this Autodijagnostika tool - returned the first one and received a second none-working tool .
After i decided i would not return it again i opened the resin filled box and was shocked by the horrible build quality.
I also have a IAW 59F.com tool for comparing, this is way better built and it does what it should.
software was sent as a download link . "

[jaelgti]

Mine is bought in IAW 59F.com works great.

[yellowstilo]

yes, i have that one too, works without problems....

[didi_du_93000]

Hello yellowstilo,
You have found a solution for free advertising????

YOU ARE A START NOW!!!!

Look here!!!

HAHAHAHAHAHAHA

[yellowstilo]

this says more about the seller than about me....this way i even can't prove he's lying , he even blocked my IP adress on his website...What serious company would do this? This is free anti- advertising....
I guess you belong to the same club - good luck with doing business this way....

[PremierD]

Second time this has happened ... if it happens again .. you will both be on the list for a short holiday ..........

[ALVARES]

Alternatively original much more functional. Nn need for computer
link: -Marelli ECP Decode (http://www.ecuvonix.com/marelli-decode-p-736.html)
manual: http://www.ecuvonix.it/doc/Marelli%20ECP%20Decode.zip

[mcgustoo]

If you want buy Realy made IAW DECODER with good quality ask me to PM. I know where buy it!!!!

[ubistvo]

If you want buy Realy made IAW DECODER with good quality ask me to PM. I know where buy it!!!!
Why you do not share here with all of us????

[sno74]

I wanted to know if anyone has bought this decoder the price is good but someone has tested....
Decoder & Emulator :: IAW 59F Decoder V5.0 HW3 - Magneti Marelli - www.autodijagnostika.biz :: ECU Repair :: ECU Testing :: ECU Supplier :: Diagnostic (http://autodijagnostika.biz/en/dekoderi-i-emulatori/iaw-59f-decoder-v5.5-hw3-magneti-marelli.html)

[autochei]

i have cryptoworkfiat and it s best programmer but work only bsi delphi 93c66

[Yura123]

Alternatively original much more functional. Nn need for computer
link: -Marelli ECP Decode (http://www.ecuvonix.com/marelli-decode-p-736.html)
manual: http://www.ecuvonix.it/doc/Marelli%20ECP%20Decode.zip
someone can leave reviews about this device.

[masterkey]

200361Can you help me please?
In an emergency, a virgin or need immo off
thanks
i read mpps v12

[pandokrator]

what about iaw59M HW< 100 of ducati bikes ?
the only one i have found is this (http://www.inovauto.com/index.php/chiptunning/programadores-ecu-obd/codificador-total-e-reset-de-cenralinas-59f-5af-e-5am.html?___store=en&___from_store=fr) but i'm not sure if work or not.
bR

[Skg312]

Hi to all
I have the so called Marelli CDC decoder hw. Until now I have decoded -hassle free- all types of IAW 59XX ecus. Recently I came accross to Bosch ME7.3H4, IAW 4AF and 5NF ecus. I have many questions and hope any of you could be helpful.
Concerning the ME7.3H4 Bosch stilo 1.2 16v Stilo ECU I have read the ecu flash and got a 512kb .bin file and the eeprom a 4kb .e2p file. How can I reset the immo on this ecu?
Thank you for your response

[smt]

if some one know this product we need information please:
D?codeur et ?mulateur :: IAW 59F Decoder V5.5 HW3 - Magneti Marelli - www.autodijagnostika.biz :: auto dijagnostika, dijagnostike, (http://autodijagnostika.biz/fr/dekoderi-i-emulatori/iaw-59f-decoder-v5.5-hw3-magneti-marelli.html)

[Master01]

if some one know this product we need information please:
D?codeur et ?mulateur :: IAW 59F Decoder V5.5 HW3 - Magneti Marelli - (http://autodijagnostika.biz/fr/dekoderi-i-emulatori/iaw-59f-decoder-v5.5-hw3-magneti-marelli.html)www.autodijagnostika.biz (http://www.autodijagnostika.biz) :: auto dijagnostika, dijagnostike,



đđĐđß$đĐßđßđßđđääđłldkf>>;*;ßßߤߤ;>>;>ßߤ]$ß$÷÷×ßß]¤¤¤]ß$$[ß[¤ĐĐß[ß...

[mcgustoo]

I have thats unit it works great!!!!!223325

[atomiczen]

someone can leave reviews about this device.
Tested today marelli ecp decode from ecuvonix
immo off 5af.p4 don't work
device told that ecu is immo off, but car don't start

[Karizmo]

Does somebody have flash for 59f that can change verification P0300
falling out of ignitions

[pegy]

Hi I too decoder from iaw.59f com, it says that sw. 5.5 where it takes? I wrote the manufacturer but does not respond to emai, the question works immo off the IAW5AM-ducati?

[fathi abbasi]

Help decodeI bought this (CDC MARELLI TNG DECODE - ECURACING.EU (http://ecuracing.eu/product.php?id_product=12)) but did not Earslo to CD Software Driver
And sent them several messages and I finally responded to Aagd think they Bad Company
Is there one of the esteemed members has this
Thanks in advance

[fathi abbasi]

Help decode
I bought this (CDC MARELLI TNG DECODE - ECURACING.EU (http://ecuracing.eu/product.php?id_product=12)) but did not Earslo to CD Software Driver
And sent them several messages and I finally responded to Aagd think they Bad Company
Is there one of the esteemed members has this
Thanks in advance

[carteknik]

What about FVDI Fiat/Alfa.... isn't it supposed to do this? I have original AVDI, but not this option and option a bit expensive.
But for difference of price might worth buying fvdi clone only for this purpose.

[marlborored]

Hi to all.
Ive got the same decoder .
I can help with IAW4AF , IAW4EF and IAW5NF.T1 and T9 :smile: but i need someone who help me with Bosch ME7xx
I connect ME73 and read DATA.Decoder reed my ecu without any problems.Now i trying to reed E2p and every time CDCM asking me to do BOOT MODE.
For BOOT MOTE is responsibility PIN20 ( ground ) but after that when im starting reading it is saying reading eeprom error.
I just want to take immo off from ecu.
Any one can help me please

[immokill]

Read eeprom and post. How can you read iaw5nf? What tool?

[spiridonas]

Hi guys i have iaw59f decoder from iaw59f.com and fgtech tool
and i want to make immo off in iaw5am.bs hw610 ducati
please can you tell me how can do this ?
need boot mode or no ?
Many thanks in advance

[linu]

you can use iaw 59f decoders, you do not need boot mode

[shanker1212]

hello mates, i went through the whole thread but couldn't decide where to buy the iaw59f decoder can anybody give us the conclusion of the whole thread ?
br

[brahimdiag]

hy pliz haw to red epprom iaw 59f.m7 for xprog help my pliz thank you

[fathi abbasi]

Hello friends
Here I find it helps in this

Hardware id: E819-BE04
What is the name
serial number
thanks

[fathi abbasi]

I bought this product from www.ecuracing.eu
But now they are not out on the Internet
Do I find it helps

[cdex]

post your id and hw

i give you what you want

[scs-mem]

Whats software version came with cdc clone?
i have open software if need,i had original interface some year ago.
Tell me know if need ,then i post
B regards

[fathi abbasi]

User name: Fathi Abbasi

[fathi abbasi]

Whats software version came with cdc clone?
i have open software if need,i had original interface some year ago.
Tell me know if need ,then i post
B regards
Please be thankful that was available Software Free

[fathi abbasi]

post your id and hw

i give you what you want
This is a program that I work with
But stopped after a computer change

[fathi abbasi]

post your id and hw

i give you what you want
That was the old chasm
But now Broken
name : abasi

ID : FHZQ-8WCP-LN8D

[fathi abbasi]

www.ecuracing.eu (http://www.ecuracing.eu/)
I think that those infamous
Aagd to have a final service
Internet site became unavailable
Aansah to deal with them

[jokersat]

WISH VERSION YOU WANT USE V 5.5 ????

[fathi abbasi]

WISH VERSION YOU WANT USE V 5.5 ????

Yes Dear
That was available works on Hardware

[scs-mem]

Hi,
your cdc is version with marelli multijet.
My software is a bit older and haven't.
I post , try.
Hope help.
B Regards

[scs-mem]

software in attachment
B Regards

[fathi abbasi]

software in attachment
B Regards
Hi,

B Regards
Thank you very much become the works now

[cemox]

Hello
I need iaw59 decoder drill layer please help

[big633]

hello
i try program 16f876A for 2 day but fail how can i do
program pickit 3
program said


2015-09-05T00:50:32+0700- Completed loading IPE.




************************************************** ***


Connecting to MPLAB PICkit 3...


Currently loaded firmware on PICkit 3
Firmware Suite Version.....01.37.15
Firmware type..............Midrange


Target voltage detected
Target device PIC16F876A found.
Device ID Revision = 6
2015-09-05T00:51:22+0700- Loading hex file. Please wait...
Loading code from C:\Documents and Settings\lek\My Documents\Downloads\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex...
Warning: C:\Documents and Settings\lek\My Documents\Downloads\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex contains code that is located at addresses that do not exist on the PIC16F876A.
2015-09-05T00:51:23+0700- Hex file loaded successfully.


2015-09-05T00:51:24+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
Programming/Verify complete
2015-09-05T00:51:29+0700- Programming complete
Pass Count: 25


2015-09-05T00:51:33+0700- Verifying...


Verifying...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Verify failed
2015-09-05T00:51:37+0700- Verify failed


2015-09-05T00:51:44+0700- Verifying...


Verifying...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Verify failed
2015-09-05T00:51:47+0700- Verify failed


2015-09-05T00:52:15+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Failed to program device
2015-09-05T00:52:29+0700- Programming failed
Pass Count: 25


2015-09-05T00:52:47+0700- Loading hex file. Please wait...
Loading code from C:\Documents and Settings\lek\My Documents\Downloads\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex...
Warning: C:\Documents and Settings\lek\My Documents\Downloads\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex contains code that is located at addresses that do not exist on the PIC16F876A.
2015-09-05T00:52:47+0700- Hex file loaded successfully.


2015-09-05T00:52:49+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Failed to program device
2015-09-05T00:53:02+0700- Programming failed
Pass Count: 25


2015-09-05T00:56:37+0700- Loading hex file. Please wait...
Loading code from C:\Documents and Settings\lek\My Documents\Downloads\zip file\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\PIC16F876A.hex...
2015-09-05T00:56:37+0700- Hex file loaded successfully.


2015-09-05T00:56:39+0700- Programming...


Device Erased...


Programming...
MPLAB's memory is blank so no programming operation was attempted.
2015-09-05T00:56:52+0700- Programming complete
Pass Count: 26


2015-09-05T00:57:02+0700- Verifying...


Verifying...
program memory
Address: 0 Expected Value: 3fff Received Value: 0
Verify failed
2015-09-05T00:57:06+0700- Verify failed


2015-09-05T00:57:17+0700- Loading hex file. Please wait...
Loading code from C:\Documents and Settings\lek\My Documents\Downloads\zip file\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex...
Warning: C:\Documents and Settings\lek\My Documents\Downloads\zip file\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex contains code that is located at addresses that do not exist on the PIC16F876A.
2015-09-05T00:57:18+0700- Hex file loaded successfully.


2015-09-05T00:57:18+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Failed to program device
2015-09-05T00:57:32+0700- Programming failed
Pass Count: 26


Target removed
2015-09-05T01:00:47+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Failed to program device
2015-09-05T01:01:03+0700- Programming failed
Pass Count: 26


Target removed
2015-09-05T01:01:18+0700- Programming...


The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x3e7
configuration memory


Device Erased...


Programming...
program memory
Address: 0 Expected Value: 2864 Received Value: 0
Failed to program device
2015-09-05T01:01:34+0700- Programming failed
Pass Count: 26


Target removed
Target voltage detected
Target device PIC16F876A found.
Device ID Revision = 6
2015-09-05T01:02:22+0700- Loading hex file. Please wait...
Loading code from C:\Documents and Settings\lek\My Documents\Downloads\zip file\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex...
Warning: C:\Documents and Settings\lek\My Documents\Downloads\zip file\59F decoder tool open project\59f DECODER tool full project\IAW59F Decoding tool by otocheck\BIN\16F876A.hex contains code that is located at addresses that do not exist on the PIC16F876A.
2015-09-05T01:02:23+0700- Hex file loaded successfully.


2015-09-05T01:02:53+0700- Programming...
2015-09-05T01:02:53+0700- Programming failed
Pass Count: 26
thanks regards

[yellowstilo]

you need the PIC 16F876 version without the A.....

[zoro1]

PIC with A is working too,for now i program two PIC-s with A on the end.The problem with PIC-KIT is that verifay is in the end ,but befor is code lock from HEX file.Therefor after programing fuse bits PIC do not answer read command corectly.But i do not know what are correct fuse bits for device with ""A"".When do programing of A device SW is conecting with HW and relays are kliking -on /off ,LED is on then off,but i coan not connect to IAW 59

[zzivo]

I spent a lot of time around creating a new project .It is necessary to aid where the errors in the project.HELP.HELP.

[mikroel]

I spent a lot of time around creating a new project .It is necessary to aid where the errors in the project.HELP.HELP.
wrong ftdi firmware
wrong PIC FW

[mikroel]

Here is sample of decoding( Virgine to Immo off )IAW5AF HW303

https://youtu.be/MpeioteCYks


Sent from my iPhone using Tapatalk

[eric paris]

Hello,
I read the 15 page of the subject , but i don't see the schema en the hex files
where can i find it ?
thanks :-)

[mps125]

Try here :)

http://www.digital-kaos.co.uk/forums/showthread.php/469512-59F-decoder-tool-open-project-with-hex-files?p=2761762&viewfull=1#post2761762 (http://www.digital-kaos.co.uk/forums/showthread.php/469512-59F-decoder-tool-open-project-with-hex-files?p=2761762&viewfull=1#post2761762)

Regards.

[eric paris]

Many thanks :)
(http://www.digital-kaos.co.uk/forums/showthread.php/469512-59F-decoder-tool-open-project-with-hex-files?p=2761762&viewfull=1#post2761762)

[magic_key]

http://www.eobdtool.co.uk/upload/pro/newest-serial-suite-piasini-engineering-master-version-car-list.pdf
piasini 4.3 uygun fiyat ve bir çok araba model :rock::rock::rock:

[mikroel]

can you read EEprom from 59F.M3 HW303 with Piasini?

[max70]

Hi, I'm looking for a iaw decode
assembled or pcb
thanks

[efiman]

we are interested

[efiman]

[QUOTE = mikroel; 3228515] μερικές συσκευές στο γραφείο μου, έτοιμες να χρησιμοποιηθούν από φίλους. :unconscious:[/ΠΑΡΑΘΕΤΩ, ΑΝΑΦΟΡΑ]
we are interested

[Gearcuit]

Good evening, does anyone have the Marelli CDC software? I found some links on the forum but they no longer work..