PEUGEOT 206 FRONT WIPERS NOT WORKING.

[nish87]

HI DK members.
I have a peugeot 206 on a 2002. It is come to me as front wipers not working at all at all speed. the owner has changed the BSI unit, front fuse box and a new wiper motor. i have plugged in my peugeot planet but come up with no fault. checked all the fuses. but all is good. i ended up changing the airbag stalk which i though would be the problem as the airbag light was on and the horn wasn't working after it was replaced the airbag light gone off and the horn is working as well. i do not understand what to do now. i even checked the wire at the motor to the fuse box but all good no wire broken. can some one please help me as the owner is blaming me for the fault now as i put the stalk in. thanks in advance

[lee_hdi]

Run a actuator test with PP to turn the wipers on. If they work then the COM is faulty. If they don't, check for voltage at the motor. If there is no voltage then the fault will probably lay in the BSI

[nish87]

Run a actuator test with PP to turn the wipers on. If they work then the COM is faulty. If they don't, check for voltage at the motor. If there is no voltage then the fault will probably lay in the BSI

HI thanks but i have checked power at the motor connector got 4pins. got 2earth and one power nthng to the 4th pin only when wiper turned on at high speed get a earth for a few seconds then goes off as the relay clicks off. and if the connector is connected back to the motor 12v goes off so no 12v when plugged in.

[nish87]

i found this on the net but do not get what it means by comms.

Peugeot 206 hatchback (1998 - 2006) - 2003 2.0 wipers not working - com 2000? | Technical matters | Back Room Forum | Honest John (http://www.honestjohn.co.uk/forum/post/index.htm?t=68902)

[EssexTech]

Basically the wiper stalk might be the problem but normally these are called comms units which are intergrated with the indicator side. If yours is seperate you have not got a Comms unit. have you the last 8 digits of the chassis number

[lee_hdi]

2002 will be mux, meaning Com2000

[nish87]

what you mean by comms?? i have changed the whole switch on the steering wheel. which is part of the airbag as well.

[EssexTech]

what you mean by comms?? i have changed the whole switch on the steering wheel. which is part of the airbag as well.

Search for Peugeot Comms 2000 on the internet . Have you the last 8 digits of the chassis number

[nish87]

sorry I'm home now will get it tomorrow. and post it on here.

[nish87]

yes i have changed the comms 2000.

[EssexTech]

Ok I will await this info

[nish87]

Ok I will await this info

42614969 chassis

[nish87]

Now in the bsi it is coming up with a permanent fault. Front windscreen wiper control.

[ammarben]

try to find a wiring digram and serch for a burnt or cut wire from BSI to wipper

[nish87]

I checked the wiring but no joy wires all gd

[morfej]

I would start at BSM (BM34 fuse box). I once have to replace that protection diode as on the picture, check also that white relay at up left directon of the diode, as it's responsibe for turning on the wipers.

Schematic between motor, BSI and BM34 on second picture.

[nish87]

i have checked the diod but it is fine that fuse boxed had been replaced aswell. by owner

[nish87]

on the switch the is only a single live wire not switching live wire double checked it with another wire n the switch live wire on the wiper connect is missing. no damaged wire or anything.

[Meat-Head]

1) Does the relay click
2) try reading this - same shit diff day http://www.digital-kaos.co.uk/forums/f152/2002-citroen-c3-no-front-rear-wipers-183426/index2.html#post940621
3)
INFERIOR WEBSITE:-

Wipers Not Working - No DTCs in BSI / Comms 2000 on Citroen Zsara Picasso , C3, C2 Berlingo, Partner, Picasso

Try this reset procedure when no DTCs are showing in the BSI or Comms 2000 on the above cars:
1 - ignition on
2 - disconnect grey 6 way plug from comm. 2000
3 - wait 3-5 secslights come on
4 - switch ign offand wait min 2mins
5 - reconnect comm. Grey plug
6 - switch ign on
7 - switch ign off
8 - put wiper stalk in auto or intermittent position
9 - put wiper switch in off position
10 - allow bsi to shut down min 2 mins
11 - switch ign on

[alejuz]

500 low speed engine control
501 Command high speed motor
503 fixed stop motor control
5265 wiper relay output
Controls the bsi telecodificate
mesuring parameters in bsi

[nish87]

I have done the reset but still with no luck.this car has given me too much head ace. i have ended up tell owner to take to dealer. thank you every one for your help and support.

[Meat-Head]

if you ever ~~~~ anything off to dealer, if you can keep straight face - ask them to report back - most do if you ask - then ask how much they got stung.

at least you updated the thread

[nish87]

lol i knw how dealers are like. but i had no choice but to. got a well know electrician but even he couldn't figure out what was wrong with it.