BSI Citroen Peugeot some instructions?

[strbr]

Hi,
How to adjust BSI correctly?
Raise hood, lock the car, disconnect battery, then unlock car, remove BSI and dashboard,lock,adjust, unlock,fit BSI and dash,lock car,connect battery, wait some time, unlock. My proceadure is like this.
My proceadure is loss of time or just remove BSI fuse?
I m going to do 307 2002.y. BSI Valeo 912 where I need to just disconnect BSI,and turn on ignition without BSI and dash will go 0 km.
Regards

[lee_hdi]

PROCEDURE FOR BATTERY DISCONNECTION (The 3 Minute Rule)

Whenever a vehicle battery has to be disconnected, switch off all equipment, interior lights etc, close the doors leaving the drivers window open.

Switch off the ignition and remove the key and any DIAG equipment.

Wait a full 3 minutes before disconnecting the battery.

The BSi must be allowed to go to SLEEP ie into "power save mode". Do not operate any equipment on the vehicle during this time. Remember, even opening the bonnet will wake the BSi on a vehicle fitted with alarm.

If the battery is under the bonnet, open the bonnet first and leave it up. 807 batteries can be dis-connected through the drivers window, remove floor cover first.

ALWAYS disconnect any DIAG equipment and do not operate any plips from other vehicles during the 3 minute waiting period.

PROCEDURE FOR BATTERY RECONNECTION

Unless otherwise instructed by Peugeot or Product Service, you must always carry out the following procedure, often referred to as a "soft re-boot", to minimise the possibility of the BSi corrupting its own software when reconnecting the vehicles battery supply.
Ensure the procedure for battery disconnection has been adhered to and importantly all BSi functions were switched off with the drivers window left down.

1 Close all doors
2 Remove ignition key if left in ignition
3 Reconnect battery. DO NOT open any doors
4 Wait 10 seconds
5 Switch on headlights through the drivers window (you will hear a "bong")
6 Switch on ignition then start the vehicle and check system functions

Here's some instructions I wrote in another post

[z786]

i have done hundreds without removing battery, aslong as the cars "asleep" i carry on

[strbr]

Hello, I've done BSI, connected dash, when i opened the door, km on dashboard was ok, i turned ignition on, and old km showed.
I ll do now BSI again, and what do I have to do after?
Peugeot 307, 2002.y.
I've used this pinout but it gave no power to dash.
http://www.digital-kaos.co.uk/forums/f174/2003-307-hdi-dash-bench-pinout-224311/ #POST 2

[CARPARTS]

307 model from 2002 has 3 types of algo in BSI
only BSI need to be done
dash and battery, i NEVER disconnected or removed.

in case of car not start after the CORRECT programming.
remove key from car, close all doors and wait 20 minutes.
dont touch anything.
open driver door, put key in contact and start engine.

[strbr]

i ve done two times BSI, and after I open door, wanted kilometers are shown on dash(140 000), after ignition first is shown -0, then (240 000)
i ve calculated with nyo.
first time i disconnected battery, 2nd time only SH fuse on BSI-i've tried to turn ignition on, and nothing happens, dash won't power up.
third luck...

[CARPARTS]

If old km come back, then NYO is not good calculated the BSI data

[CARPARTS]

post dump here from 912 bsi

[strbr]

post dump here from 912 bsi

here it is mate. 241 037
i need 147xxx
by the way, there is history in this dump, so if its possible to remove it.

[z786]

u have to power on dash before u connect bsi

[strbr]

u have to power on dash before u connect bsi

ok, i removed bsi, and i turned ignition on, dash wont power up,is it ok? ignition has to remain on while i connect BSI?

EDIT:
Adjusted BSI, and kilometers stayed until i turned on ignition :s:, no luck for 4th time, can somebody modify dump i posted.
and i switched ignition on, without bsi, but it didnt power up.

[CARPARTS]

here is correct dump

[CARPARTS]

....here is dump....

[z786]

switch ignition on and hold trip reset button for a few secs, nothin will show in display

or jus take out and power up on bench

[strbr]

Thanks for tips and dump, was a bit late for dump,cause i ve been doing dash. I've done BSI + dash. guess its 5th luck...

[mouss]

you must do dash my friend it's nec and soldering 14 points