CARPROG FULL

[carradio2001]

Did anybody try only to ACTIVATE any software?
You are my guest :burnout:then will you have a dead carprog clone!

Carradio2001.

[markony79]

You are my guest :burnout:then will you have a dead carprog clone!

Carradio2001.

No, I have Carprog Oiginal, but not full version :(
I was try to Activate some programs, but not work...

but after update the software...all my version work good

[Min2xx]

Astra H HAS security code on ecu. I can bet.
You a right, H have in ECU. I today test with original, but without success. Finally read dash and program new key :)

[Carbit]

I bought one, got it already but installer is damaged, is there an address to download installer?

[RCS]

I bought one, got it already but installer is damaged, is there an address to download installer?

Try this...

http://www.sinodownloads.com/down/download/ecutool/3503222-carprog.rar

[robertg288]

Try this...

http://www.sinodownloads.com/down/download/ecutool/3503222-carprog.rar

hi how to download this?

[88diablo]

Mouse over on the download link then left click?

[dimet]

And then unzip and run carprog.exe

[robertg288]

somebody tell me please how to take pincode out from eeprom which software is the best?

[Music73]

somebody tell me please how to take pincode out from eeprom which software is the best?

Depends on what car you want to get pin from.... There are a few pincode extractor softwares on the forum if you do a bit of a search in the immo and ecu sections...

Music73

[homicida]

Like i say:)
The china make all posible!

[olo_3]

hello do You know on which pin ist "UART1" on ARM ?

[autocargo]

hello do You know on which pin ist "UART1" on ARM ?
Check this out

[olo_3]

eventually PA30 = PIN42 (page 33 , page 9 pdf)
;)

[robertg288]

somebody tell me please adapter d1 have to be split with a1 when i conect may cr to vectra c 2006 1.9 cdti many thanx

[tricoredc17]

Has anyone carproga PCB design with codecard.

Thanks

[hauwkee]

so if you do all those modification can this clone work properly or it a long process for people who are not good at repacking .debug and other

[aqua_life]

I would like to buy Carprog clone in Europe.
Not china because in my country taxes are high... And from europe there are no taxes.
Do you know an european store where I can buy it?
Or if someone from DK sells it...
Thanks

[kizagt]

Fiat Punto 1.9 d 2001
503.000.344.900 C141
46833457 68 90689
Successfully done via obd

[solitaire]

I would like to buy Carprog clone in Europe.
Not china because in my country taxes are high... And from europe there are no taxes.
Do you know an european store where I can buy it?
Or if someone from DK sells it...
Thanks

You can buy here: www.codecard.lt (http://www.codecard.lt) :party:

[Carbit]

i have received a clone, works ok

When i use a newer version of sw new functions say NA ( not available ) do you all have this problem?

[andy99]

i have received a clone, works ok

When i use a newer version of sw new functions say NA ( not available ) do you all have this problem?
This is not problem
this is clone old version 4.01

[arturkob]

Hello can anyone have the new version 5.09 carproga?

[andy99]

Hello can anyone have the new version 5.09 carproga?

version 5.09 kill your clone

[koyot]

carprog works well with new version

[tatop]

carprog works well with new version

What version do u refer?

Inviato dal mio GT-P1000 usando Tapatalk

[sepistar]

yesterday did mileage an a6 MM73 dash,year 2004/goes very well.carprog 4.01.
later models after 2006 not goes(unknown version of A6/Q7)

regards

[ziko]

Anyone tested Fiat Croma CAN? Safe or not? Need Fiat cable+A1?

Tnkx

work ok

[yeager]

hi is it possible activate Citroe C5 dash on CP clone? i try v4.01 and v4.95 but C5 dashes have only n/a

[scary]

no it no working on original as well

[tatop]

hi friend, can i modify by obd grande punto and 500 with car prog clone??? with the ver 4.85??

[PiciGSM]

Hi!
I bought a china clone Carprog.I can't read 68hc05b6(Astra F airbag ecu,5WK4072) whit A10 adapter.Why?What I make wrong?
Anybody help me,Please!

[joaopereira]

someone can help me
i have received a clone,
I run also the D1 and A1 test and both fail

uart0 ok
uart1 ERROR
Pin 1 Error (sort to + 5v)
pin 2 ok
pin 3 ok
pin 4 ok
pin 5 ok
Pin 7 Error (sort to + 5v)
pin 6 ok
POWER ok

Is it possible to fix error on CarProg repair kit ?
thanks

[tatop]

U use a9 adapter?
d1 with clone in test dont go.

Inviato dal mio GT-P1000 usando Tapatalk

[joaopereira]

hi
I tested with d1

[athlonxp]

Maybe anyone knows solution for non working renault megane 2 keycard programming? Laguna via k-line works good, megane2 via can not work. Thanks.

[Min2xx]

And latest Carprog 5.18
Use own your risk !!!

[bluedid]

Fiat Panta 2006-2007 via obd works ok

[rubin_miki]

And latest Carprog 5.18
Use own your risk !!!
this is for clone or for orig? :) orig soft for clone not working, you can kill your clone :)

[olo_3]

And latest Carprog 5.18
Use own your risk !!!

thx - works with clone

[spychu14]

thx - works with clone
Is it some new functions ??

[aksimo]

thx - works with clone

Are you sure taht the soft not kills the clone ? :alberteinstein::alberteinstein:

[whiskeyman]

And latest Carprog 5.18
Use own your risk !!!


has this been tested with clone?

[builderis]

CR 5.18 lock my Clone 4.01 :bawling:

[carradio2001]

For the moment working good -->
Of course only features for 4.01, the others ... n/a

Carradio2001.

[whiskeyman]

has anyone managed to read 95160 in circuit with carprog with a6 adaptor?

[bearheroes]

has anyone managed to read 95160 in circuit with carprog with a6 adaptor?

Yes and it works great.

[olo_3]

Are you sure taht the soft not kills the clone ?

no,
my clone works fine with 5.18

[honingkoning]

no,
my clone works fine with 5.18

Is renault megane nec active (by clusterplug) and did you test it.

Regards Adam

[romucifer]

Maybe anyone knows solution for non working renault megane 2 keycard programming? Laguna via k-line works good, megane2 via can not work. Thanks.
hello look in a1 adaptator http://www.codecard.lt/carprog/carprog-repair-kit-4x-74hc125-4x-22uf-capasitors-1x-mcp2515/prod_566.html

[romucifer]

hello my carprog work read 95160 in eeproom programme but in dasbord 206 bsi not read 95160
why

[xtech]

try wersion 3,75

[rust55]

anyone read st92f120

[romucifer]

try wersion 3,75
yes work in v3.75 dashbord bsi 95160 why dont work in v4.01

[judor]

Today my carprog clone is not defined usb. Have " No device attached " Has Done ReFlash . flashing fine not mistake. Did Not help. Has Done change ARMSAM7x256 , ReFlash. Did Not help. Usb cable has changed. The Jack usb soldered. Help who knows.

[gjuzel]

hi m8....Today I got carprog Clone Sw. 4:01 .. but I cant read..write 24c eeproms 93c read but no write.and with whom I work better software .. 4:01 ... 4:05 .. 4:37 .. 4:50 .. 4.85 .. 4.86..or .. 4.95 ???? Chinese vendor says it works only with 4.01 software..... other software .says kill car prog(clone)is this true???? ... Many members seys work with other software????? thanks Any help will be of use to me....sory(translate)

[bearheroes]

hi m8....Today I got carprog Clone Sw. 4:01 .. but I cant read..write 24c eeproms 93c read but no write.and with whom I work better software .. 4:01 ... 4:05 .. 4:37 .. 4:50 .. 4.85 .. 4.86..or .. 4.95 ???? Chinese vendor says it works only with 4.01 software..... other software .says kill car prog(clone)is this true???? ... Many members seys work with other software????? thanks Any help will be of use to me....sory(translate)

for read/write 24cxx and 93cxx you have to make mods.check in this thread to find the solutions.

[ciekawy]

Is renault megane nec active (by clusterplug) and did you test it.

Regards Adam



not active


does not work
Dashboard
"No Respouse from unit"
some solution to this problem ?????

[ALEXEI]

clones not work on dashboards with eeproms

[athlonxp]

clones not work on dashboards with eeproms
My clone 4.01 works fine with eeproms without any change. I made a lot of clusters, airbags with 93x, 24x, 95x eeproms . Also works with saab 9s12, renault hc08 and others mcu. Works on laguna card programing, but megane not work. Maybe I am lucky. I buy it from gocardiag.

[ligno1]

cp clone, focus 2005 diret 9S12, ok

[djoko.k]

Can i use adapters from clone on original?

[gjuzel]

yes...you can

[briangsm]

hi i cant read MC68HC11E9 airbag vww3 old audi a3 97y witch carprog clone software Version 4.01 today he came
reset tx and rx raised use adapter 10 and try witch 12v does not work any suggestions

[Multipla]

I have a problem, I have to reset an Audi A3, now I wonder, I can not read the dash 46060 KM with the golf 5 files but can't edit it, plus all the ch software I tried some entries are n/a (not autorized) now I wonder what does it mean to change software unless they are enabled with a file that tells me n/a I the problem lies in the file, lib I in AT88 as I understand CarProg processor is protected and + with passwords. I maybe I'm ignorant on but wonder how you can enable the file n/a and once and for all, let's explain how to enable the file n/a if not we could change software as we want but we have not solved anything. would all files of the bike but I can't because they aren't enabled. then a 4.86 don't do anything if the 4.01 can do what the software makes me do, but I get angry when I + 4.95 and are not enabled. The 2006 A3 I can read but can't write it. 4.95 software see A3 2006 is n/a. Thanks in advance.

I have a problem, I have to reset an Audi A3, now I wonder, I can not read the dash 46060 KM with the golf 5 files but can't edit it, plus all the ch software I tried some entries are n/a (not autorized) now I wonder what does it mean to change software unless they are enabled with a file that tells me n/a I the problem lies in the file, lib I in AT88 as I understand CarProg processor is protected and + with passwords. I maybe I'm ignorant on but wonder how you can enable the file n/a and once and for all, let's explain how to enable the file n/a if not we could change software as we want but we have not solved anything. would all files of the bike but I can't because they aren't enabled. then a 4.86 don't do anything if the 4.01 can do what the software makes me do, but I get angry when I + 4.95 and are not enabled. The 2006 A3 I can read but can't write it. 4.95 software see A3 2006 is n/a. Thanks in advance.

[robertg288]

anybody have carprog with function ecu edc 16 i have but n/a? thx rob

[Multipla]

Have a solution of Audi A3 2006? in version of 4.96 I look this function but is n/a dont function.

[gjuzel]

carprog 4.01 clone ..cant read 24c eeprom why??

[autocargo]

carprog 4.01 clone ..cant read 24c eeprom why??

You have to search on this thread. There are a few things that can go wrong. It's all have been discussed here...

[domel45]

anybody have carprog with function ecu edc 16 i have but n/a? thx rob

Opel EDC16 working ok, VW EDC16 don't working on CP clone, because VW EDC16 use A1+ cable.

[CRFKE169]

hello. im new her and post something for the 1st time. im from belgium and i wont to order it in china but when i was looking i found 4.5 but when you see the discription or foto's its 4.1. does some one have a link from te last update.i work in a garage and i had a good expirience whith a clone from china renault can clip. so i was hoping it is also so good. sorry for my bad english riding. :-p

[Shmortz]

the clone is for version 4.01, will work with newer version but everything new in the version will be n/a

[CRFKE169]

ther must be a way two update frome 4.1 two 4.... but i cant find the post here some wher. dos anybady nows where i can find it or how. thx a lot al ready.

[bearheroes]

ther must be a way two update frome 4.1 two 4.... but i cant find the post here some wher. dos anybady nows where i can find it or how. thx a lot al ready.
just download newer soft and use it without update the hw because then you will kill it.

[carradio2001]

Opel EDC16 working ok
Are you sure ? You are FIRST person who say this, evereyone else says not work on EDC16 Opel CP Clone 4.01 !

Carradio2001.

[Multipla]

Have a solution of Audi A3 2006? in version of 4.96 I look this function but is n/a dont function.

[Multipla]

Please can help me. tanks.

[ALEXEI]

Please can help me. tanks.

Dont try it on A3. Even ori tool kill this dash

[solitaire]

Dont try it on A3. Even ori tool kill this dash

original has repaire function.

[Shmortz]

if you talk about A3 dash RB8, clone works like a charm, I have an error with that dash using super k+can Plus, then repair it with carprog clone in few seconds...

[briangsm]

hi i cant read MC68HC11E9 airbag vww3 old audi a3 97y witch carprog clone software Version 4.01 today he came
reset tx and rx raised use adapter 10 and try witch 12v does not work any suggestions


Hi all my mcu HC11 and HC5 i have a problem
,maby my mcu is damaged also i try other mcu

my clone id is 081105CAR001773I
tested

epp 24cxxx r/w work ok
93cxx , r/w work ok
95080 r/w work ok
airbag clio 2 via adapter a15 mcu HC912b32 r/w work ok

[gjuzel]

hi m8....Today I got carprog Clone Sw. 4:01 .. but I cant read..write 24c eeproms 93c read but no write.and with whom I work better software .. 4:01 ... 4:05 .. 4:37 .. 4:50 .. 4.85 .. 4.86..or .. 4.95 ???? Chinese vendor says it works only with 4.01 software..... other software .says kill car prog(clone)is this true???? ... Many members seys work with other software????? thanks Any help will be of use to me....sory(translate)

[8k65m]

See http://www.digital-kaos.co.uk/forums/f174/carprog-full-247647/index122.html#post1786895

[solitaire]

today start christmas promotion
Carprog basic 424.00eur
update to full 800.00eur
1224 (all softwares ready for sale at the moment -on the date of your purchase)
some money - and will not have problems with the clone

[gjuzel]

Mine reads 95320 and others 95xxx but can`t read 24cXX. "Serial number" of my cp is 0223. Anyone with this serial number and the same pcb can confirm that his clone can read or not 24c ? Also saw that some cp clone and original have more 2 caps on the board. I need the value of these caps. my image car prog 4.01

[sepistar]

Dash A4 RB4,20sec OK.
regards

[judor]

Today my carprog clone is not defined usb. Have " No device attached " Has Done ReFlash . flashing fine not error . Did Not help. Has Done change ARMSAM7x256 , ReFlash. Did Not help. Usb cable has changed. The Jack usb soldered. Help who knows.
Power +5 , +3.4 , new Quartz 12.000 .
Possible death of Eeprom ????

[draganpg]

where is new carprog update
?

[draganpg]

hi all everyone. I am training new software for carprog where download?

[xtech]

look here is all version soft

[mijatx]

1. Clear Crash Airbag Ford BOSCH 0 285 001 24.. via K-line on bench
Clear Crash Airbag Renault Megane II on bench(eeprom read/write) -OK!
2. Add Key Renault Clio II 2002 - OK!
3. Read/write 24CXX & 93CXX - OK!
4. Read/write MCU HC12 - OK!
5. Add Chip-Card Renault Megane II 2003- BAD!( no connection via CAN)
6. Add Chip-Card Renault Scenic II 2004- BAD!( no connection via CAN)
7. Read PIN code Renault Clio II/Laguna II/Kangoo via OBD(K-line) -OK!
8. Clear Crash Airbag Peugeot 206 1.4hdi 2004 (on bench eeprom read/write) -OK!
9. Change KM P206 dash (dash connector)- Read KM OK! Write failed!!!
10.Change KM Renault Laguna2 (dash connector)- Read KM OK! Write OK!!!

[automan]

@MIJA TX
what software version u used?

[digimile]

hi
how to clear crash data on Vw jetta 2006..with carprog...over obd 2

i use 4.85 version and it read write all eeprom 93cxx,24cxx,95cxx in circuit....
thanks

[Music73]

hi
how to clear crash data on Vw jetta 2006..with carprog...over obd 2

i use 4.85 version and it read write all eeprom 93cxx,24cxx,95cxx in circuit....
thanks

I find that on airbags it says it has cleared but doesn't actually clear it... But most vw airbags can be done k-line. If you enter the model no. It will tell you what lead and what process is needed.

Music73

[Maartinj]

Gents, who can upload / send me Immo data from VW micronas cluster read via Carprog ?
For example Caddy / touran / Mk5 since 2004 , up to 2010

[adam28]

Can anyone tell me if the carprog clone works by OBD for mileage correction on a 2008 onwards Fiesta?

Cheers

[piter200]

my adapter Ford pins
male 3 - 3 female
4 - 5
5 - 4
11 - 11
16 - 9
is that correct?

[workdamnyou]

Can anyone tell me if the carprog clone works by OBD for mileage correction on a 2008 onwards Fiesta?

Cheers

I tried a few, none worked.

Same with Mk7 Transit and 07+ Mondeo.

[Maartinj]

Guys, did anybody have immo data read via Carprog ? Immo data from VW - can be micronas for example Golf MK5 any year , or NEC cluster.

[adam28]

I tried a few, none worked.

Same with Mk7 Transit and 07+ Mondeo.

Its easy to do by soldering, but for OBD for quickness shame its not working.

Maybe i will see if clone ford km tool is working for fiesta 2008 onwards...

[Music73]

Its easy to do by soldering, but for OBD for quickness shame its not working.

Maybe i will see if clone ford km tool is working for fiesta 2008 onwards...

Mine works fine for late fiesta via obd... Don't use ford adaptor cable just A1. Late transits are done by clipping the soic8 think its a 93c66 but can't remember of the top of my head... Mondeos I don't know about as I've not tried one of them.


Music73

[Music73]

Guys, did anybody have immo data read via Carprog ? Immo data from VW - can be micronas for example Golf MK5 any year , or NEC cluster.

I have a mk5 micronas read with carprog will try to remember to post it on Monday..

Music73

[tatop]

Radio Opel cd30 code OK
ECU hibrid 1.7 dtl Opel corsa c on bench code OK virgiize OK dump re ad band write OK vin ok

Inviato dal mio GT-P1000 usando Tapatalk

[workdamnyou]

I had tried with the A1 cable as well as the Ford one...no go with either one, with my interface anyway.

I've never tried VW Micronas or Nec with Carprog as I have original Abritus for these.

[electrones]

for read/write 24cxx and 93cxx you have to make mods.check in this thread to find the solutions.

Hi guys
I'm having trouble with my carprog clone 4.01, i wonder how to do mods.check????
I thank you in advance for help, grateful

[AKAINTERN]

hello!
tell me what the latest version of the software is working with a Chinese clone?

[bearheroes]

hello!
tell me what the latest version of the software is working with a Chinese clone?
every sw works with carprog clone.just don't update it via internet.

[AKAINTERN]

failed to dash A6 2006 with software version 4.01, 4.37 (unknown version of A6/Q7).
if you use soft 5.15 do?
dies carprog?

today made dash Passat B6 2006 with software version 4.37!
4.01 software is not made this dash!

[twincam]

A6 C6 is not working with Carprog even with original.

[solitaire]

A6 C6 is not working with Carprog even with original.
with original work perfect.

[twincam]

Mine is not working from 2005 to 2007.

[AKAINTERN]

Now installed software 5.15, started with a clone, the counter does not appear
Check back tomorrow for the car of his friend the Audi A6 2006 with 5.15 software

[judor]

5.15 kill you clone.

[AKAINTERN]

I just run 5 times 5.15 software with his clone - all ok

[lagas]

with original work perfect.

i confirm that with org works perfect

[AKAINTERN]

here are my pictures when connected my clone and run soft 5.15

[AKAINTERN]

i confirm that with org works perfect

which version of the software works A6 C6?

[claudio35]

Ford scape 2008 not working obd2. connection error

any help?

tks

[fine2day]

Thx.....very usefull :)

[Multipla]

I read this dash, A3 year 2006, but dont write the dash. How did you do? I've only read 5 Golf Protocol but I couldn't write anything. I have 4.01 I anger doesn't solve the problem. That solution might adopt. Thank you all in advance and also those people who responded first. Shmortz says his CarProg works fine but then spiegaa how did. Thank you

[AKAINTERN]

Today checked dash for AUDI A6 2006 with software 5.15, failed writes (unknown A6/Q7) !
someone did such a machine ?

[lagas]

Yes with orginal, and not remember sw version. Maybe 5.21... Costume from codecard

[marmaro]

Hi friends!!!! If anyone of you tested version 4.1 with adapter a9, my carprog test ok adapter a1 ok, but do not respond d1
and were a little afraid to use it.
It would be great if someone has tested your. pleeessss

[marmaro]

sorry for bad english!

[bearheroes]

Hi friends!!!! If anyone of you tested version 4.1 with adapter a9, my carprog test ok adapter a1 ok, but do not respond d1
and were a little afraid to use it.
It would be great if someone has tested your. pleeessss
a9 doesn't work with clones.

[marmaro]

a9 doesn't work with clones.
I made a9 by carcode and test my clone: results carprog list of pins ok ok ok ok ok ok test on a1 in car -ok , d1-not respond ,if someone has adapter a9 please try.
If anyone has, please upload the pinout of the a6 carprog clip - mine does not read on plate, only desoldering chips and turned upside down.

[spychu14]

Two simple questions :

1.What chip is on D1 Adapter ?
74HC125M ?

2. Anyone see difference after flashing MCU with DK dump ?

I don't have counter yet but i will flash MCU if this help.

Thanks

[marmaro]

Two simple questions :

1.What chip is on D1 Adapter ?
74HC125M ?

2. Anyone see difference after flashing MCU with DK dump ?

I don't have counter yet but i will flash MCU if this help.

Thanks
chip in my D1 adapter is no name and in carprog too.
Can I easily check them somehow?

[tatop]

Radio Opel cd30 code OK
ECU hibrid 1.7 dtl Opel corsa c on bench code OK virgiize OK dump re ad band write OK vin ok

Inviato dal mio GT-P1000 usando Tapatalk

http://www.digital-kaos.co.uk/forums/f175/opel-1-7-dt-hibrid-carprog-308878/

[marmaro]

Alone solved the problem with the reading of the adapter A6:bounce:, wires on the clip were confused, if it helps somebody gives the correct configurations

[filutek]

Two simple questions :

1.What chip is on D1 Adapter ?
74HC125M ?

2. Anyone see difference after flashing MCU with DK dump ?

I don't have counter yet but i will flash MCU if this help.

Thanks

Yes chip 74HC125.After uploading there is no difference counter returns.

[Music73]

Have a look in the carprog mcu reprogramming thread, there is some info about modifying the code so the counter resets itself every reboot.. its slightly above my head but sure it will make sense to some people....

Music73

[briangsm]

Hi What is the value resistor on photo i try today do stilo 2004 via agapter A1 but don work maby this resistor is bad.

second photo adaptera A1 orginal

[simbad]

I tried to connect Stilo and punto 2003/2004 DASH with A1 but no connection. Should A1 be modified or something? Thanks.

[markony79]

Hi What is the value resistor on photo i try today do stilo 2004 via agapter A1 but don work maby this resistor is bad.

second photo adaptera A1 orginal

check here modification for A1

its have for OLD and NEW A1 cable
I have original Carprog, and after this modification, not get problem anymore

[tatop]

check here modification for A1

its have for OLD and NEW A1 cable
I have original Carprog, and after this modification, not get problem anymore

Hi friend, are u removed this resistor?

Inviato dal mio GT-P1000 usando Tapatalk

[markony79]

Hi friend, are u removed this resistor?

Inviato dal mio GT-P1000 usando Tapatalk

No,
you must PUT THERE Resistors

but better tomorow, i will post the original modification for A1 and A1+ for Carprog

[hacko12]

There is new ver 5.27. Enjoy

[markony79]

this is from original carprog , from last year on the site

[markony79]

Also have for A1+

[markony79]

and more for carprog, repair kit

and here is last modification for A1

S7.17 - Opel Insignia, Astra J odometer programming by OBDII (CarProg A1 adapter) (http://www.codecard.lt/carprog/software/carprog-dash/s7-17-opel-insignia-astra-h-odometer-programming-by-obdii-carprog-a1-adapter-/prod_612.html)

if can not read the Opel dash,
but not have problem for another dash, after modification

CHEERS

[markony79]

Here is all modificated from site

CarProg repair kit (http://www.codecard.lt/carprog/carprog-repair-kit-4x-74hc125-4x-22uf-capasitors-1x-mcp2515/prod_566.html)

[gjuzel]

Here is all modificated from site

CarProg repair kit (http://www.codecard.lt/carprog/carprog-repair-kit-4x-74hc125-4x-22uf-capasitors-1x-mcp2515/prod_566.html) no counter..repair carprog.

[paul_12345]

and more for carprog, repair kit

and here is last modification for A1

S7.17 - Opel Insignia, Astra J odometer programming by OBDII (CarProg A1 adapter) (http://www.codecard.lt/carprog/software/carprog-dash/s7-17-opel-insignia-astra-h-odometer-programming-by-obdii-carprog-a1-adapter-/prod_612.html)

if can not read the Opel dash,
but not have problem for another dash, after modification

CHEERS

I bet fiat dont work with resistor? how about add a switch connect to resistor so you can switch the resistor on/off

[mastaflex]

no counter..repair carprog.

is it your work? at least put credits

[AKAINTERN]

There is new ver 5.27. Enjoy
working with a clone?

[elchip]

no counter..repair carprog.
No counter only in your dream ;-)

[8k65m]

no counter..repair carprog.

Already been discussed. http://www.digital-kaos.co.uk/forums/f174/carprog-full-247647/index77.html#post1651738 Troll?

[hacko12]

working with a clone?

This is original software, you can use it if update your clone with no counter flash..

[AKAINTERN]

i read dump from panel A6 C6 2006 but carprog writes (unknown A6/Q7) can anyone correct mileage by dump?
need 87000 km.

[tatop]

This is original software, you can use it if update your clone with no counter flash..

Hi, where i search file no counter flash for use new software?

Inviato dal mio GT-P1000 usando Tapatalk

[hacko12]

Hi, where i search file no counter flash for use new software?

Inviato dal mio GT-P1000 usando Tapatalk

http://www.digital-kaos.co.uk/forums/f171/carprog-reprogramming-final-solution-285338/

[briangsm]

check here modification for A1

its have for OLD and NEW A1 cable
I have original Carprog, and after this modification, not get problem anymore


i do 3 modification as a picture A1 clone before modification and

A1 after my modification I hope that now will work fine.

[markony79]

i do 3 modification as a picture A1 clone before modification and

A1 after my modification I hope that now will work fine.

Now must working

[briangsm]

I hope so :) thx

[andor777]

Hello

Someone is AT88sc dump (carprog)

I wanted to read:afraid::stupid:
But I read the previous ones
Carpog dont work ,dead
Please help

[hacko12]

Did anyone tested cp clone on Reno clio dash 1999-2003 HC08 diag change milleage and make right dump calculation for Peugeot BSI's module?

[bodzio012]

Did anyone tested cp clone on Reno clio dash 1999-2003 HC08 diag ?

I did, laguna and scenic, therefore I think that clio work very good

[hacko12]

Someone try?
Audi A6 2004-2008 Magnetii Marelli

[trader1990]

Someone try?
Audi A6 2004-2008 Magnetii Marelli

not working well, it destroys the cluster

[briangsm]

My carprog today starts counter 254 units left and nod verify epprom maby i send for complaints i dont know ... any suggestions?

[andkl2810]

This is not a problem :bounce:!!! http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-step-288814/

B R

[cp2010]

My carprog today starts counter 254 units left and nod verify epprom maby i send for complaints i dont know ... any suggestions?


china shit !

[elchip]

china shit !

U have right 100%

[Maartinj]

Guys. Who can post here IMMO data read by CAR PRog ? i am looking immo data from VW Micronas cluster Mk5 or any Caddy / touran since 2004.

[briangsm]

china shit !

U have right 100%
very useful BIG HELP :)


This is not a problem !!! http://www.digital-kaos.co.uk/forums/f171/carprog-mcu-reflash-step-step-288814/

B R
i try this thx

[ets]

thanks merci

[honingkoning]

I did, laguna and scenic, therefore I think that clio work very good

I tested on clio 908 not good, laguna instead was good.
I think something worng with login.
Berlingo dash with 908 also good.

Regards Adam.

[solitaire]

Guys. Who can post here IMMO data read by CAR PRog ? i am looking immo data from VW Micronas cluster Mk5 or any Caddy / touran since 2004.

golf V 2004

[andkl2810]

have you got the original ???

[dolfi]

Thank You For This Useful Post

[psx1]

Carprog new ver 5.27
There is new ver 5.27. Enjoy

hacko12hacko12First of all thanks for carprog Hacko12
version 5.27 that these messages attached Hacko12 worked with the clone?
someone tried to?
I'm thinking of buying a Chinese clone carprog and wanted to know if it worked this version?
to fix megane3 laguna 3 and abs ecu and serve?
Version 4.1 seems to not fix these cars.
But 5.27 is to select.
have to crack the program or just connecting the machine work?
Good end of the year and best new year to all

[einet]

You must have christmas dream! :)

You must have more time to read all 128 pages to know what is CP clone and CP ~~~~inal before ask some questions?


Happy new 20133333 f all

[Music73]

Even with newer s/w on cp clone a lot of the new functions are still unavailable

Sent from my HTC One X using Tapatalk 2

[djdanny]

:ciao:


Enjoy!
no pass

Clone tested. no locked clone.
No internet update!

[elchip]

:ciao:


Enjoy!
no pass

Clone tested. no locked clone.
No internet update!
Even you want update clone online serial is blocked on they server ;-)
So do not worry about update ...

[digimile]

hi
clone work on this new software or not ???
thanks

[elchip]

hi
clone work on this new software or not ???
thanks
Work but new SW do not get you more function ;-)

[spychu14]

Dashboard Golf V 2009 Micronas FIS - Read immo/KM OK

[briangsm]

whats the value of the resisters on the picture?

[filutek]

2R20=2,2ohm ,1001=1kohm/0,1W

[briangsm]

i fighting with my carprog clone 2 weeks ago works corectly, but some resistors are lightly fried i must it change, now dont read 24x and 93x , and starts counter

changed 4x 74HC125 from farnell changed usb slot and repair a1 i do test a9 adapter , test witch d1 +a9 device no responde from unit some one test it?
sometimes carprog test says Pin 8 errors short to 5v.

ahh this wonderful carprog............:laugh:

sory for my English



http://dl.dropbox.com/u/106625011/CP%20photo/6.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/7.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/modify%20a1%208.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/9.jpg
http://chomikuj.pl/bestuse/CAR+DIAGNOSTIC/Carprog/Repair+Carprog/2013-01-05+10.57.52,2285162330.jpg

[yellowstilo]

you have to make a test adapter with just a connector and some resistors - not put the resistors after the (D1 ?) pcb adapter.....

EDIT: i just noticed you already tried that.....

[autocargo]

No clone will pass D1 test.

[TULGEYWOODMAN]

i fighting with my carprog clone 2 weeks ago works corectly, but some resistors are lightly fried i must it change, now dont read 24x and 93x , and starts counter

changed 4x 74HC125 from farnell changed usb slot and repair a1 i do test a9 adapter , test witch d1 +a9 device no responde from unit some one test it?
sometimes carprog test says Pin 8 errors short to 5v.

ahh this wonderful carprog............:laugh:

sory for my English



http://dl.dropbox.com/u/106625011/CP%20photo/6.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/7.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/modify%20a1%208.jpg

http://dl.dropbox.com/u/106625011/CP%20photo/9.jpg
http://chomikuj.pl/bestuse/CAR+DIAGNOSTIC/Carprog/Repair+Carprog/2013-01-05+10.57.52,2285162330.jpg






.................................................. ....

[electromech]

BMW EWS read and write OK but the key reader didnt work so had to read key info from Zedbull and just inserted data and it worked like a charm

[dataprog]

hi
207 2011 peugeot Not good bsi

[bodzio012]

BMW EWS read and write OK but the key reader didnt work so had to read key info from Zedbull and just inserted data and it worked like a charm

How did you read EWS by carprog??? I try and for me not work?

[gsmik]

Carprog don't read vin in dashboard AUDI 2004 CAN. Reads only VIN. Do you have any solution ?

[mislav88]

Carprog don't read vin in dashboard AUDI 2004 CAN. Reads only VIN. Do you have any solution ?
which dash? VDO, Bosch or MM?

[gsmik]

VDO SIMENS AUDI A3 2004 year

[judor]

How did you read EWS by carprog??? I try and for me not work?

Check cable pin . China cable BmwEws wrong.

[vageric]

someone could read motorola HC11 E9 with this tool?
we have tryed for ford airbag but no joy!

[doslamer]

Hello m8, does anybody have carprog software v3.07 to share?

[briangsm]

I tried does not work .
http://www.digital-kaos.co.uk/forums/f174/carprog-full-247647-post1788817/#post1788817



someone could read motorola HC11 E9 with this tool?
we have tryed for ford airbag but no joy!

[scary]

china start selling jtag whit sollution for counter
How to update Carprog and solve locked problem : (http://www.obd2repair.com/news/how-to-update-carprog-and-solve-locked-problem-a-283.html)
maybe help for somebody :D

[doslamer]

It is on the forum time ago -> http://www.digital-kaos.co.uk/forums/f171/carprog-reprogramming-final-solution-285338/ <- for free!

[digitaltech]

It is on the forum time ago -> http://www.digital-kaos.co.uk/forums/f171/carprog-reprogramming-final-solution-285338/ <- for free!


yeah everytime is it pop up to the top of the topic page i see "final solution" i have mixed feeling as to accuracy of that statement. hint google it..

[ovi_dk]

china start selling jtag whit sollution for counter
How to update Carprog and solve locked problem : (http://www.obd2repair.com/news/how-to-update-carprog-and-solve-locked-problem-a-283.html)
maybe help for somebody :D

yess,after hunting for infos on forums they came with solutions wath other guys solved long time a go!!:))))
copy-paste thats all china hunters!!!

[judor]

I have found Google. See.

BIG-SYSTEMS Fahrzeugdiagnose Systeme (http://www.big-systems.net/webshop/product_info.php?products_id=305&language=en)

CarProg Full
Project Files are consist of:

1. Dump for
AT91SAM7S256
including configuration file for H-JTAG (Wiggler).

2. Dump for
AT88SC25616C
including unique 5-digit password.

3. PCB protel files for
Main Unit
, OBD (
A1
) adapter and
D1
adapter.

4. Schematics for all other adapters such as A4, A5, A6, A7, A10, A11, A15, A16, A17...

5. Special software to
reset counter via USB
(does not require dismounting any part).

6. Document about
Important CarProg hardware modifications
.

7. Documents which includes manuals for key programming, airbag reset...

Project has been tested and it is 100% working. Please note that passwod of Crypto EEprom is not the same as chinese so you will not be able to read it.

[elchip]

I have found Google. See.

BIG-SYSTEMS Fahrzeugdiagnose Systeme (http://www.big-systems.net/webshop/product_info.php?products_id=305&language=en)

CarProg Full
Project Files are consist of:

1. Dump for
AT91SAM7S256
including configuration file for H-JTAG (Wiggler).

2. Dump for
AT88SC25616C
including unique 5-digit password.

3. PCB protel files for
Main Unit
, OBD (
A1
) adapter and
D1
adapter.

4. Schematics for all other adapters such as A4, A5, A6, A7, A10, A11, A15, A16, A17...

5. Special software to
reset counter via USB
(does not require dismounting any part).

6. Document about
Important CarProg hardware modifications
.

7. Documents which includes manuals for key programming, airbag reset...

Project has been tested and it is 100% working. Please note that passwod of Crypto EEprom is not the same as chinese so you will not be able to read it.

On that website is not original PCB and password for AT88 is not 5 DIGIT ;-)

[tas_daz]

i want to buy clone from carsung carprog.they told that is good quality from first factory.what you said about that?try anyone from carsung?thanks

[8k65m]

I bought there. Had to send back for replacement. Replace with the proper good quality. I wrote about it on the forum.
Regards.

[einet]

Hello,

How can say what i can do for repair this error!
I change all HC125D to HCT125M and make the test that whose OK after change all IC, then i conect D1 and Test adapter and make test NOT OK.
I disconect all and make CP + test adapter and bekome all the time Pin 8 are short and change HC125!.

I make the change but all the same!

Is pin 8 from 25 conector the Line 8?

thanks

[Dudi_1981]

Any one try read Simentec 71.5 by CAN ?

[gsmik]

I read Simentec by CAN and I changed PIN. Works fine.

[hacko12]

Yesterday i got my carprog clone and i want to work mileage on Audi A4 RB4 dash but i dont see any explanation how to do that. I read hire that this clusters work with carprog.
1. Did i need to with A1 OBD adapter or i need to take off cluster and work on the eeprom?
2. How to fix mileage show error on screen?

Thank you!

[electromech]

How did you read EWS by carprog??? I try and for me not work?
Just used supplied cable and ground to pin 22 I think and it worked

[rm23]

i have carprog from carsung, it is the same carprog like from cardiag or ecutool.... no difference ! buy from gocardiag good price same quality

[scary]

hello i want to share 5.31 version witch works thit clone whitout any modification and give some extra function.
fully working and tested .


sorry for my english
102 downloads and only 4 user say thanks very nice guys :(

[djnesio]

hello i want to share 5.31 version witch works thit clone whitout any modification and give some extra function.
fully working and tested .


sorry for my english

Thanks for your upload..

Does this file work with CarProg clone v4.01 ?

[scary]

yes it works no problem at all i try it whit my clone 4.01 original clone :)

[emiliogsm]

extra function ?

[scary]

yes is add how much i faund toyota keys more vw plus i saw airbags for fiat renault as weell i still no have time to search all functions

[Music73]

I wonder if the extra airbags will work though... They don't work on most of the newer ones till now... Carprog looks like its working but infact doesn't do anything to the data...

Sent from my HTC One X using Tapatalk 2

[scary]

i do loads fiat doblo 08 and up airbags never have any problems .it maybe becouse is just deliting actual crash not all faults so sometimes is just few bits so please compare dums before and after

[bodzio012]

Somebody tried CP china peugeot biper, Citroen nemo or fiat florino???

[bobik43]

What I must we do to v5.31 new function? (for example ECU EDC16,..) New .lib file? New content memory hardware? Thx

[scary]

biper nemo and qubo same algo like doblo 06 onword last time i do qubo and use doblo algo try whit fiat km tool not work

[vladtimmy]

my fiat stillo 2002 worck perfect

[tatop]

my fiat stillo 2002 worck perfect

Can u modify by Obd grande punto ?

Inviato dal mio GT-P1000 usando Tapatalk

[bodzio012]

biper nemo and qubo same algo like doblo 06 onword last time i do qubo and use doblo algo try whit fiat km tool not work


I tried today but not work, dash is the same such as grande punto (95080) which not work for me too ,

[scary]

can you upload yuor dump and say how much it have and how much you want km

[AvechuchoAxel]

How did you read EWS by carprog??? I try and for me not work?

I fried EWS last time I try.... FUc#ing clone... !!! Airbags detect the crash, read and write OK, but if you read and compare original file with the "repaired" one..... using different programmer is the same file.... So not working for me.

[meteor80]

I fried EWS last time I try.... FUc#ing clone... !!! Airbags detect the crash, read and write OK, but if you read and compare original file with the "repaired" one..... using different programmer is the same file.... So not working for me.

Airbags repair works only to version 4.37
Upper wersion not works

[sepistar]

Airbags repair works only to version 4.37
Upper wersion not works

good to know m8.
regards

[bodzio012]

can you upload yuor dump and say how much it have and how much you want km

I done by UPA but if you want I can attach dump

[quinnd]

Hi guys, how is carprog v4.1 to adjust mileage by obd2 on Ford Ranger? 2008. Is it safe to try?
Last time is removed cluster and eeprom but by obd would be much easier

[scary]

firs remove dash read eeprom safe and then try to do by obd if somethings go wrong you gave back up . and if it works next time you now i alltime do thit not tested cars like that :)

[ovi_dk]

What I must we do to v5.31 new function? (for example ECU EDC16,..) New .lib file? New content memory hardware? Thx

u must buy oem carprog and function will be enable:)
:celticparty:

[bodzio012]

Has anyone photo ews a11 working cable?

[bearheroes]

Has anyone photo ews a11 working cable?
this (http://www.codecard.lt/carprog/adapters/a11-bmw-ews-adapter/prod_82.html) is better than photo...

[bodzio012]

this (http://www.codecard.lt/carprog/adapters/a11-bmw-ews-adapter/prod_82.html) is better than photo...

I've seen it, but I want to see china cable, I had problem with my cable ( I changed 2 wires) and I want to compare or just a cable or something more

[FAR2012]

:celticparty:

[mitch2]

Has anyone photo ews a11 working cable?
your photo

[bodzio012]

your photo

I know how it looks from the outside because I have, are you okay, you feel good??
I'm interested in photo inside

[mislav88]

Audi A6 2000 4B0920900C 2J74Y worked flawlessly :top:

[cuiuda]

Hi
I have a CP 4.01 clone. It's work with 5.25 software version? I see that this version of the software can connect on EDC16. Is this true? Can be used with clone 4.01 ?
Thank you

[sepistar]

Hi
I have a CP 4.01 clone. It's work with 5.25 software version? I see that this version of the software can connect on EDC16. Is this true? Can be used with clone 4.01 ?
Thank you

mot work mate,you need new cable.+.give a search.it has been already discussed.
regards

[mitch2]

I know how it looks from the outside because I have, are you okay, you feel good??
I'm interested in photo inside
sorry !!!! look now, i thought that were 2 photos

[Pakli30]

What is the problem?

My carprog clone dont read fiat stilo 2001 ODBII, and dont read 95040 eprom.
A9 adapter test OK!
reserved 4 74HC125.

Please help

[robertg288]

hi i have carprog ori but i cant read eeprom 95320 anybody know what is wrong? thx rob

[d.zio]

ford fiesta 06 dashboard with 9s12 with obd......didnt work
opel corsa c temic airbag module with oj66d inside.....worked
opel vectra b ecu delco hybrid pin code read and reset.....worked

[scary]

What is the problem?

My carprog clone dont read fiat stilo 2001 ODBII, and dont read 95040 eprom.
A9 adapter test OK!
reserved 4 74HC125.

Please help
did you do in circuit if yes try to remove .
i done loads of 95... no problem

[paulek9]

im about to program mcu motorola but didnt find th correct information will look in some tutorial or do i have tolook to the data sheet to match the pin of the carprog how can i do it???

[judor]

The Back side EEprom AT88SC25616C
http://s017.radikal.ru/i428/1301/ba/b2b75762bf56.jpg (http://www.radikal.ru)

[Music73]

did you do in circuit if yes try to remove .
i done loads of 95... no problem

I think he was trying to do it via obd..

[makadam]

Can I make odometer modification on instrument cluster or ECU on VW passat 2006 B6 model with carprog clone and thisi made by OBD or using adapters and some soldering in PCB board?

[Shmortz]

in dash can do it without any problem, but in ECU must do it by BDM, carprog clone does not have option to do it in ECU

[einet]

Hi,

I receve a carprog that have all the time on pin 8 short to GND!!!
I change all 74HC125D to 74HCT125M and have all the time this pin 8 to GND!, I have in the KF50 regulator 5.6V and on the KF33 have 4.6V!
Is this normal? or i must have in KF50 +5.0V and on the KF33 must have 3.3V?

What can i do more?

einet
thanks