nissan nats5 read

[Mezo]

Hi All
Please how i can Read EEprom Mcu A2C11776 (M220f0403) in immo Nats5
by X-prog m or upa


http://www.digital-kaos.co.uk/forums/attachments/f178/40250d1290661928-how-reading-tms3705a-nissan-nats-5-immobox-nissan-maxima-nats5-2001.jpg

[TISHKA25]

Hello! Try this ...

[Mezo]

Thanks ill try

[Mezo]

any body help me to Read this eeprom in this MCU St A2C11776 i try to read it as St7 but no way

[smokey08]

Why do you need to read this? If you want pin code, post a picture of the sticker and I will generate it for you.

[lashkar97]

if u need key and pin code data than i think u no need of this eprom read . u can read bcm by DLC . and also programm new key by OBD2 .

[Mezo]

i need read eeprom in this MCU St A2C11776 and write other immo damaged

[Mezo]

if u need key and pin code data than i think u no need of this eprom read . u can read bcm by DLC . and also programm new key by OBD2 .

no find bcm in the care

[ray-ray]

Year, make and model just like if you had to work on these car. What question would you ask your customer?

[Lardle]

i need read eeprom in this MCU St A2C11776 and write other immo damaged

Just find another immo from scab and post photo here u will get a pin to programed a new key simple

[nasir]

just buy another imm unit & post the picture some one will generate the pin for u why u want to waste the time in reading your damage imm unit .

[Stevens Ferreira]

Can you give me the pin code please? 540612

[brend]

Try.....0090.....

QUOTE=Stevens Ferreira;3321756]Can you give me the pin code please? 540612[/QUOTE]

[Stevens Ferreira]

Thank you friend
Try.....0090.....

QUOTE=Stevens Ferreira;3321756]Can you give me the pin code please? 540612[/QUOTE]

[KILL_THE_IMMO]

i have the same issue immobilizer is stolen so i bought a used one
i must read ecu zexel eprom and immobilizr mcu and write a set dump
or just program a new chip??

[mapexo]

Hello! Try this ...

interface used for sw link? pin diad is kline or L-line?

[electro10]

Hi all,

Someone can give me the pin code, please?

Thank you a lot

947445

[alex_r_2001]

Hi all,

Someone can give me the pin code, please?

Thank you a lot

947445

Hello try 7699 .... Goodluck

[Ninjor s]

......pin is 2289

[electro10]

I tried 7699 with AVDI I have the message "Immobilizer module not respond".
Tomorrow I will try 2289.

Nonetheless I read immobilizer with VVDI, dump in atchment. Dump has pin code?

Because the situation was: original is damaged, no data. So, I bought an used (in picture that I posted) and I will program new keys.

Thank you all

[alex_r_2001]

I tried 7699 with AVDI I have the message "Immobilizer module not respond".
Tomorrow I will try 2289.

Nonetheless I read immobilizer with VVDI, dump in atchment. Dump has pin code?

Because the situation was: original is damaged, no data. So, I bought an used (in picture that I posted) and I will program new keys.

Thank you all

Instacode from your label and also from your bin file match for same pin code of 7699...

If you have communication problem with other Nats related modules it will not accept pin code even if correct pin code is input into scanner...

[electro10]

And can identify the keys ID in dump?

Thank you

[Ninjor s]

Instacode from your label and also from your bin file match for same pin code of 7699...

If you have communication problem with other Nats related modules it will not accept pin code even if correct pin code is input into scanner...

You right mate my bad this one is from Germany pin is 7699947523

[electro10]

I tried with Abrites and with IM608 and no communication possible.

I tried make a new key with protag (abrites) but abrites hasn´t NATS5 to make a key by dump.

So, in this case, only possible to communicate with NATS5 is on bench with VVDI...
And with dump is possible understand if MCU is ST or TMS?

Any ideas, please?

Thank you a lot

[Ninjor s]

What nissan is this and ecu info.

[electro10]

What nissan is this and ecu info.

Nissan Navara D22 2.5TD
motnh/year: 12/2012

[Ninjor s]

Post ecu dump+nats

[electro10]

Post ecu dump+nats

Before, I tried next:

On bench, connect abrites to NATS, and communicate. I read pin code by abrites, and is 7699.
After, I do key learning. I programmed one key, abrites told that is ok, but no start. Red light always on.
I read dump and abrites clears some bytes.
Can you identify in dump where is ID key saved?

Is necessary ECU dump?

Thank you

[Ninjor s]

......key 5E-2E-34-8B
your car wont start becouse immobox+ecu not syncro,if you wanna sync ecu with new immobox you need to add key in the car.

[electro10]

......key 5E-2E-34-8B
your car wont start becouse immobox+ecu not syncro,if you wanna sync ecu with new immobox you need to add key in the car.

Ok thanks.

I tried by OBD with Abrites, IM608 and MVP. Nothing.

If I read ECU dump, is possible sync ECU and NATS?
Dumps in attachment:
"NATS used": NATS dump read with VVDI
"ECU_24C02": ECU dump read EEPROM 24C02

ECU:
23710 VK560
407917-072

Original key has ID (read with VVDI key tool): 0100D9345603


Thank you a lot

[Ninjor s]

Ok thanks.

I tried by OBD with Abrites, IM608 and MVP. Nothing.

If I read ECU dump, is possible sync ECU and NATS?
Dumps in attachment:
"NATS used": NATS dump read with VVDI
"ECU_24C02": ECU dump read EEPROM 24C02

ECU:
23710 VK560
407917-072

Original key has ID (read with VVDI key tool): 0100D9345603


Thank you a lot

......sync oky just add key

[electro10]

......sync oky just add key

Thank you! and what is the pass?

Is necessary add key by OBD or bench? What tool can do this?

[Ninjor s]

pass in pm, you can add key on bench no problem.

[electro10]

Doesn´t work... The difference: now, when I turn ignition on, read light is off and go on only after a fews seconds; before was always on.

So, I think that key is not programmed. Can I use original key or I need program a new transponder? What transponder? ID60 / XT27 make by xhorse? TPX2?

Thank you a lot

[Ninjor s]

Doesn´t work... The difference: now, when I turn ignition on, read light is off and go on only after a fews seconds; before was always on.

So, I think that key is not programmed. Can I use original key or I need program a new transponder? What transponder? ID60 / XT27 make by xhorse? TPX2?

Thank you a lot
i dont know why you failing to do this easy job.
read original key will add it for you, key is id 60

[electro10]

i dont know why you failing to do this easy job.
read original key will add it for you.

I don´t know too, I think that is tool to add key.

Key original:

947950

Thank you a lot