Cloud ibox unbranded solo clone

[piratedish]

Oh, that will be the case then. Too bad.

[bighun]

i am now using the latest blackhole 2.0.5 image without any freezing problems it is the openbox s6000hd which is just the same box as the cloud ibox without a fan it has got the v3 chip in it i don`t know if that makes a difference i am using a twin fan usb notebook cooler to keep my box cool

[mo.p]

i am now using the latest blackhole 2.0.5 image without any freezing problems it is the openbox s6000hd which is just the same box as the cloud ibox without a fan it has got the v3 chip in it i don`t know if that makes a difference i am using a twin fan usb notebook cooler to keep my box cool

hi m8 thank u very much for that can u update it to blackhole 2.0.5b???????? plz let me know if u can

[bighun]

hi mo.p have just done the upgrade to 2.0.5 rev b it is working fine so far

[mo.p]

Thank u so much m8y i am sorted now my fav image Thanks

[mo.p]

hi guy i am useing this bh 2.0.5.b image its working ok but when i try to use usb for cross epg or picon then i lose signal black screen but when i take usb out works fine plzzz any help/info would be greatly appreciate

[theonlymisteron]

Ok Got one of these a couple of days ago WTF what a complete pile of rubbish.

Please don?t buy one. Ok reasons why.

Unpacked it ---- cheap nasty.

First thing I noticed was the USB ports are upside down, not a real problem I agree.

The USBs are not marked so which is the front (on a normal VU+) and which is the back? Well ok the USB nearest to the back is the one for flashing.

Imaged went on fine (blackhole latest version). But after a while the unit started to error. I checked it and it was very hot.

I open the bottom to check the fan. It was spinning, now here is the bad part. When you put the bottom panel back on the card reader stops the fan dead.

Now if you don?t have the unit switched on you probably would not notice this,but I had it running and the fan buzzing noise told me what was going on, everytime I tryed to pop the back on again fan stopped. Tried moving the cable but no good. In the end removed the card reader (not realy a solution)

OK so the clone was a bit cooler. So put on bench test for a while. OH DEAR. Hang Hang Hang every 10-15 mins totaly unresponsive until pulling power

Remote looks like an original but sure dont feel like one !!!!

So to round up it is terrible!!! Buy a real VU+solo with real warranties great looks and performance

It is now back in its box ready to return to Amazon

[debully]

yeah this thing iant for everyone. My mate got one and the fan failed after a week. Mine is silent and runs only warm. There's loads of info on this thread and it takes some reading but it's pot luck and price vs hassle compared to a real VU+ solo. I personally have the card reader installed to the back panel and the box running upside down as a precaution. I have found a really stable version of VIX from 'Ten Below' which runs the IPTV and 1channel/icefilms nicely. I am really pleased but I'm a bit geeky and enjoy a challenge.

Thanks to everyone who contributed to this lengthy thread.

[kometal2007]

Hi, I just bought this receiver based on the user experience and price ofc, but could you write the pros and cons of the different images that you've tried and what image you're running now, how it is best to set up to avoid the freeze issue, i ordered the one that comes with fan installed is it enough or I should change the fan with bigger one?

Thanks

[kaisar1]

trying to setup autobouquet on blackhole 1.7.9 and keeps getting green screen when searching

I been having freezing + green screen issues for about 2 weeks. Any backups would be much appreciated. Thanks.

can anyone upload a backup for the ibox cloud.

[caskman]

trying to setup autobouquet on blackhole 1.7.9 and keeps getting green screen when searching

I been having freezing + green screen issues for about 2 weeks. Any backups would be much appreciated. Thanks.

can anyone upload a backup for the ibox cloud.

I have the Blackhole 2.0.5 installed and it's 100% stable.

[thebox]

If u have a backup of your image would handy thanks

[Search38]

I was thinking to put this box on sell here in my country, but i am not going to do that, as i think this box has many problems, I will give you some advice with Clones, I have tested lot of Chinese Clone Boxes as re seller, I can say that some are good some bad, so it is big difference between clones, as the factories that make them have not any real standards, in Shenzhen where all this things are made, are lot of small factories, or even some of this boxes are assembled at home, Only few factories have some good standards, been told this by Chinese, so you need to know where to buy, even me that been buying there for many years, it take me hours to find out what is what???, I sell Skybox F5 at the moment which si not bad, F3 and F5 are the best versions of Openbox-Skybox, myself ordered VU+ Solo2 Original, waiting to come!!!!!!!!!!!!!!!!!!

[wakkaday]

which is the best image for this box. currently have vix intalled?

[bighun]

i don`t know why some people are slating this box i have got both the 60000hd without a fan and the cloud ibox with the fan and they have both been excellent boxes using blackhole 2.0.5b without a problem no freezing no green screens or any of the reported problems for ?60 delivered from china by fedex in 3 days for an enigma 2 box with all the plugins you can get it is excellent value for the money if you want a cheap enigma 2 box buy one if not don`t buy one why pay ?300 when you can buy this one for ?60

[MENTE SICULA]

HI
someone can tell me is this decoder run with Original image or only with pacthed image for VU+ clone?
TNX

[andyd123]

HI
someone can tell me is this decoder run with Original image or only with pacthed image for VU+ clone?
TNX

It will run just fine with original image.

I recommend Blackhole 2.0.5 been running for a while now with no freezing at all.

[colly127]

Hi i have put a good few out to my friends with no problem at all. Plus the real cpu so u can use images.
Ans any people with problems with fans u can get the on ebay for ?3 or china ?1.50p
oor u can jusy take the broken fan out ang use a ?3 usd fan from ebay ie one of thUSB Cooler Cooling Pad 2 Fans For Laptop Notebook PC UK Laptop cooler YL-818 | eBay (http://www.ebay.co.uk/itm/USB-Cooler-Cooling-Pad-2-Fans-For-Laptop-Notebook-PC-UK-Laptop-cooler-YL-818-/261257508920?pt=UK_Computing_LaptopAccess_RL&hash=item3cd4293838)ese

[MENTE SICULA]

yes but is not recommended to power the fan from the internal USB ports
Try it: vga fan | eBay (http://www.ebay.it/sch/i.html?_odkw=vga+fun&_sop=15&_osacat=0&_from=R40&LH_PrefLoc=2&_trksid=p2045573.m570.l1313&_nkw=vga+fan&_sacat=0)

But I would like to ask if works on usb port the the usb wifi SKYBOX | eBay (http://www.ebay.it/sch/i.html?_odkw=usb+wifi+decoder&_sop=15&_osacat=0&_from=R40&LH_PrefLoc=2&_trksid=p2045573.m570.l1313&_nkw=usb+wifi+SKYBOX&_sacat=0)

[byson1984]

What images and version is best for this box?

[orientville]

I'm using blackhole 2.0.4 image with blackhole 2.3.0 cam box is very cool no overheating problems whatsoever.All the usual plugins tsmedia etc are running great.So for ?60 from china i've no complaints at all.

[MENTE SICULA]

I would like to ask if this box works on usb port with the the usb wifi SKYBOX | eBay (http://www.ebay.it/sch/i.html?_odkw=usb+wifi+decoder&_sop=15&_osacat=0&_from=R40&LH_PrefLoc=2&_trksid=p2045573.m570.l1313&_nkw=usb+wifi+SKYBOX&_sacat=0)

tnx

[djpopeye1971]

cananyone tell my how to flash the box for blackhole

[digicon]

cananyone tell my how to flash the box for blackhole

A guide is here for the S6000HD which is identical: http://www.digital-kaos.co.uk/forums/f184/openbox-s6000hd-upgrade-guide-sharing-setting-up-guide-338992/

[xstream2013]

hi can anyone tell me where to download image for this box
thanks

[MENTE SICULA]

here:
Solo (http://www.digital-kaos.co.uk/forums/f188/)

[iguana]

I wanted to put a 60 x 60 12v fan where the card reader
Is, but I'm not to sure which fan to put in,
The orginal fan is 12v - 0.08A
Can I put a fan with more current or less?
I've seen a fan with 12v - 0.07A
and another one with 12v - 0.13A
Will these be ok to use with the 2 pin connector
On the mainboard?
Thanks

[rigsby71]

I would like to ask if this box works on usb port with the the usb wifi SKYBOX | eBay (http://www.ebay.it/sch/i.html?_odkw=usb+wifi+decoder&_sop=15&_osacat=0&_from=R40&LH_PrefLoc=2&_trksid=p2045573.m570.l1313&_nkw=usb+wifi+SKYBOX&_sacat=0)

tnx


yes it does, got one set up myself like this.

[rigsby71]

hi can anyone tell me where to download image for this box
thanks

same instructions as per a VU Solo, look in that section.

[rigsby71]

I wanted to put a 60 x 60 12v fan where the card reader
Is, but I'm not to sure which fan to put in,
The orginal fan is 12v - 0.08A
Can I put a fan with more current or less?
I've seen a fan with 12v - 0.07A
and another one with 12v - 0.13A
Will these be ok to use with the 2 pin connector
On the mainboard?
Thanks

Might be safer just to plug in one of those usb laptop coolers & stick it underneath.

[kkkkklaur]

to remove card reader safely (no freeze software) conect pin 5 and 6 ( numbering from any ditch 10-pin edge)motherboard card reader conector with a HDD jumper, CLOUD IBOX work no freeze only with fan to a chipset cooler best image no freeze and stable is OPENAAF(OPEN ATV) Ver 20130812 not new because new image interrogate MAC and black screen

this is the good image software stable ,and no freeze

openatv-3.0-vusolo-20130812_usb.zip

download here

http://dfiles.eu/files/qevo1ql8l

after instal the image download ccam (inside software conect to server and install) after instal ok and install c lines conect with ftp and instal in folder usr/keys/ccam.cfg


This information is only for educational use not use for view TV PROVIDER.
A good day...

[moskolio]

hello

Is there a way to disable the fan when in stand-by?
I got it as a cheap second box for the bedroom but i can not tolerate the fan noise in the night.
I am running openpli 3.0, tried installing the fan control plugin but it says "box has no fan-control hardware"
Is there an image that has fan control?
i know i could just turn it off in the night but id rather not for various reasons.

i would seriously appreciate your help on this one
Thank you in advance

[kkkkklaur]

Cloud not have hardware fan control .....
you have this option

1. Put the OLD gsm phone charger 5v to move the fan and the speed is slow
2.Use the function --deep standby--- (image OPEN AAF) to stop total the cloud with remote...
3.use the fan with automatic speed control with heating (with NTC sensor inside)

[skybandit]

A guide is here for the S6000HD which is identical: http://www.digital-kaos.co.uk/forums/f184/openbox-s6000hd-upgrade-guide-sharing-setting-up-guide-338992/

I tried to install a Blackhole image (and then OpenVix, and then OpenPli...)....

All I end up with is a blank screen!!!

[moskolio]

Try using images that were built before the middle of August 2013.
Blackhole 2.05 works, 2.06 does not work.

If you prefer pli try this:
http://www.digital-kaos.co.uk/forums/f187/openpli-3-0-beta-vusolo-20130820_usb-zip-last-known-clone-safe-openpli-vu-solo-365571/

[moskolio]

Cloud not have hardware fan control .....
you have this option

1. Put the OLD gsm phone charger 5v to move the fan and the speed is slow
2.Use the function --deep standby--- (image OPEN AAF) to stop total the cloud with remote...
3.use the fan with automatic speed control with heating (with NTC sensor inside)

thank you for your answer
i am sorry but i can not understand what you mean on number 1 and number 3.
can you please try to explain them a bit better

1. what is an old gsm phone charger?
3. Do you have a picture or a guide of this setup?

[billalahmed]

any1 got a safe vix image which i can install on my cloud ibox, I tried installing vix 3.0.743 but get blank screen. Also whats the best image out there to use?

[MENTE SICULA]

try this:

OpenPLi-4.0-beta-vusolo-20130902 (http://goo.gl/U0BBRx)

[lombard]

any1 got a safe vix image which i can install on my cloud ibox, I tried installing vix 3.0.743 but get blank screen. Also whats the best image out there to use?

you need build 721 or lower

[billalahmed]

I cannot seem to get picons to load up correctly, they seem to be in the wrong order, also out the 643 picons only 57 get transferred to my usb. any help?

All sorted, turned out my usb was playing up so tried another usb.

[kkkkklaur]

Cloud ibox best and stable image download link (FREE download in regular mode)
http://dfiles.eu/files/qevo1ql8l (http://dfiles.eu/files/qevo1ql8l)

THE NEW IMAGE (all team image) after ( in general 15-08-2013) use protection by chip v3.2 version and is need upgrade software security chip v3 to version v3.2 (only for v3 chip) for work with new image software.
v1,v2 security chip need hardware upgrade.

[kkkkklaur]

thank you for your answer
i am sorry but i can not understand what you mean on number 1 and number 3.
can you please try to explain them a bit better

1. what is an old gsm phone charger?
3. Do you have a picture or a guide of this setup?

Used to power the fan clone old phone charger (5v) so not push the limit source is sized and powered fan with two separate wires sticking them through the slot left free box fan will go slow and you will not make noise more and eating less ef cooler can let go non stop.

[calcu]

My 2 cents.

Installed every image i can imagine..., now BH 2.0.5 updated to version b with Cccam is working perfectly.

This box just have only one problem....

When you reboot it, sometimes (i don't know when or why), it just outputs a blank screen, but you can see the network leds working fine and the blue light (the remote one), working fine too.

i think it's something about power.

If you have an usb fan or usb stick attached, it only boots up 1 time of 10.

if you don't have anything connected it will boot, but, if it doesn't boot, just switch the unit off, wait a moment a turn it on, in 3 or 4 times it will boot.

when it doesn't boot, i could see this log with putty:



setenv('prefix', '/usr', 0)
setenv('exec_prefix', '/usr', 0)
setenv('bindir', '/usr/bin', 0)
setenv('sbindir', '/usr/sbin', 0)
setenv('libexecdir', '/usr/libexec', 0)
setenv('datarootdir', '${prefix}/share', 0)
setenv('datadir', '/usr/share', 0)
setenv('sysconfdir', '/etc', 0)
setenv('sharedstatedir', '/com', 0)
setenv('localstatedir', '/var', 0)
setenv('libdir', '/usr/lib', 0)
setenv('localedir', '${datarootdir}/locale', 0)
setenv('prefix', '/usr', 1)
setenv('exec_prefix', '/usr', 1)
setenv('bindir', '/usr/bin', 1)
setenv('sbindir', '/usr/sbin', 1)
setenv('libexecdir', '/usr/libexec', 1)
setenv('datarootdir', '/usr/share', 1)
setenv('datadir', '/usr/share', 1)
setenv('sysconfdir', '/etc', 1)
setenv('sharedstatedir', '/com', 1)
setenv('localstatedir', '/var', 1)
setenv('libdir', '/usr/lib', 1)
setenv('localedir', '/usr/share/locale', 1)
resolve: resolve ${datadir}/enigma2/encoding.conf
resolve: -> /usr/share/enigma2/encoding.conf
resolve: resolve ${libdir}/enigma2/python
resolve: -> /usr/lib/enigma2/python
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
resolve: resolve ${libdir}/enigma2/python/
resolve: -> /usr/lib/enigma2/python/
Segmentation fault


thinking that normally it works fine... i believe that some capacitator is small or something like that, but... i don't have any idea about which can be :(.

Despite of this.. i'm happy with this box xD

[lombard]

i had about 4 of these, and loaded in openpli 3.0 and not had any issues, image loaded to get full 7 day epg, etc , had them running for 2-3 weeks no crashes or problems at all , i found vix 3.0 would last a day or 2 before crashing

[orientville]

New updated version of this box hits the market 600mhz bigger quieter fan 1g flash/1g ram v3 chip anyone tried this box yet.Its called cloud ibox 2

[kkkkklaur]

ATTENTION! update RS232 Cable CABLE IS NOT NULL MODEM cable or RS232 classical.. The dongle is attached to the cable or change the connection pin plugs as prescriptions (VU +) pin failure may damage the STB software

[MENTE SICULA]

this is the real ferrari cable for VU+ Solo/Duo clone and its corresponding interface
http://s24.postimg.org/dkkzxt6ap/5894 (http://postimg.org/image/dkkzxt6ap/)

[orientville]

ATTENTION! update RS232 Cable CABLE IS NOT NULL MODEM cable or RS232 classical.. The dongle is attached to the cable or change the connection pin plugs as prescriptions (VU +) pin failure may damage the STB software

Is this needed for the new ibox2 if using blackhole image.

[kkkkklaur]

This is the pin modification conection for CLOUD IBOX (BCM 7325 chipset) (null-modem cable)to upgrade security chip wihout dongle adapter

pin 2,3,5- PC

pin 6,4,5- Vu+ (CLOUD IBOX)

for use the pack software update search with google and download this...

....security chip update V3.2

(Not use another combination of pins for modify null modem cable for security cip upgraded to v3.2 that damage the receiver software.
UPGRADE v3 to v3.2 is ONLY! for receiver with v3 security chip inside..
For receiver v1 or v2 security chip inside is neeed hardware(not software) upgrade (new upgrade with chip v3.2)
For inexperienced people is reccomended to use software images in the first half of August 2013 and let the receiver as is for now.

Another 3 alternative is
1.DOWNLOAD CLONE VU SOLO Software

search in google window ---- np-ulc---- and in first adress link go to:
Receiver / Clone Boxen/Images/Clone Vu+ Ferrari/Clone Solo

2.search in google window
___Official DE OpenBlackHole BH 1.4____
and use image for your security chip inside (in first link open in google have all version for vusolo Ferrari (cloud ibox)

2. Search and download latest patch images works for with new security upgrade

BlackHole 2.0.6 Ferrari V2/V3 by Toysoft


information is only for educational use and Viewing Pay TV without a valid subscription is illegal



222142

[calcu]

this may sound silly but...
which side of the cable is attached at the pc and which is at receiver?

[sjuran]

this may sound silly but...
which side of the cable is attached at the pc and which is at receiver?

pin 2,3,5- PC

pin 6,4,5- Vu+ (CLOUD IBOX) ..... adapter in VU

[radmir]

For working with lathest sowtware image is need to use the lastest upgrade FERRARI security chip to v3.2 READ THIS

???? It can't work! At least becouse ibox has only 3 pins in serial port conector. And it has different security chip inside, not ferrari.

[billalahmed]

any1 got hold of the cloud ibox 2? are they anygood and do they support the latest vix image? they seem to have the same chassis as the dm800.

[digicon]

any1 got hold of the cloud ibox 2? are they anygood and do they support the latest vix image? they seem to have the same chassis as the dm800.

The Cloud ibox2 is a clone of the maxdigital XP1000 receiver

[lombard]

The Cloud ibox2 is a clone of the maxdigital XP1000 receiver

hi you sure as spec seems higher

Cloud ibox2 Powered by a 600Mhz Broadcom MIPS CPU, 4G DDR 3RAM and 2G flash. 3D,PVR ready,

Supported officially by OpenPLi, OpenAAF and the ViX Team.

support 3D ,3G,USB,WIFI,HBBTV,Youtube,IPTV,Emu firmware.

and another version

Cloud ibox2 Powered by a 600Mhz Broadcom MIPS CPU, 1G DDR 3RAM and 1G flash. PVR ready,

Supported officially by OpenPLi, OpenAAF and the ViX Team.

support 3D ,3G,USB,WIFI,HBBTV,Youtube,IPTV,Emu firmware.

are they really supported officially ?

Thanks

[satsmo]

I have just deleted numerous posts quoting "other" forums. Next time will be an infraction followed by a ban for those that continue to do so.

[MENTE SICULA]

ok sorry satsmo

is someone want try new Black Hole Image 2.0.6 patched by Toyfot (all thanks go to him)
can read here and leave same feedback
Vu+ Solo : BlackHole 2.0.6 Ferrari V2/V3 by Toysoft (http://www.digital-kaos.co.uk/forums/f188/vu-solo-blackhole-2-0-6-ferrari-v2-toysoft-372208/)

[balbao]

UPGRADE v3 to v3.2 is ONLY! for receiver with v3 security chip inside..
For receiver v1 or v2 security chip inside is neeed hardware(not software) upgrade (new upgrade with chip v3.2)
hi, how to know the security chip version? is there any way to find out?

[kkkkklaur]

hi, how to know the security chip version? is there any way to find out?

Search with google this......

8a8f8


and in first link IN RANK you find answers....for security chip Ferrari receiver....

Receiver CLOUD producer sell cloud ibox have v3 chip inside

search this in google...

Original Ferrari Chip Cloud Ibox Version3

......and 2 link in rank is AIRSAT CLOUD IBOX V3 chip

Upgrade how to ( source:Ferrari forum)
Use the RS232 cable and dongle type device (or modified null modem cable with pin explain in page 20 in this thread)that came with my box to update the firmware to the latest v3.2.

To do this make sure your computer has a real physical COM port, USB adapters won;t work reliably and that the OS is Windows XP.

Make sure the Vu Duo is switched off, plug the RS3232 dongle into the Vu Duo, plug one end of the cable into the dongle, the other end into the COM port on the PC/Laptop.

Download the latest v3.2 firmware and unpack to a suitable location and then run the program renewaes.exe, this should automatically detect the COM port, if it doesn;t then you have a problem so check all connections.

If the program detected a COM port then you can continue so click on Load file and select the file vu_2ver_22m_130110_sec_isp.bin.

After the file has loaded switch on the Vu Solo/Uno/Duo, the program should start flashing the firmware to the v3 security chip, a progress bar will be displayed and a message will pop up when the Update has completed.

The box is now ready, so go and get whatever image you want to use then use the normal USB method to flash the box and then enjoy.
---------------------------------------------------------------------------------------------------------------------------------
For download the update security pack (v3 to v3.2) search in google this

V3.2 upd_vu62k.zip

This information is only for educational use and Viewing Pay TV without a valid subscription is illegal

[kkkkklaur]

In the future arrived CLOUD IBOX II (Shenzhen Air Digital)

clone of Receiver MK DIGITAL XP1000 (or MAXDIGITAL XP 1000)

[MENTE SICULA]

it will take imagine VU+ ?

[kkkkklaur]

Appear on AliExpress as the sale has not yet appeared in the Chinese say Officially Supported by OpenPLi, OpenAAF and the ViX Team and how we see that first to see if the price is competitive ....

[digicon]

it will take imagine VU+ ?

Its a Clone of a NON Vu+ receiver so will not take any of the Blackhole images only image supported are those mentioned above

[Pillhead]

The New CLOUD IBOX !!!The best affordable receiverSimilar to VU+Solo ans DM800HD
V.3 : Buit-in fan
Satellite and IP Channels Receiver

My alien 8900 box has just gone kaput and ive been offered one of these as a replacement? Apparently its a newer model that runs cooler. Probably just the same but with a crappy fan installed.

I dont mind doing a bit of modding myself if it needs a new or larger fan etc.

BUT does the current firmware run stable on these boxes now? Ive read most of this thread!

Cheers guys and gals

[bighun]

i am running both the openbox s6000hd and a cloud ibox both have the v3 chip in them and i am running ferrari blackhole 2.0.6 which they run perfectly the s6000hd has not got a fan in it and runs a wee bit hot the ibox has a fan and it is virtually noisless i am running a lot of plugins also for the price they are a cracking wee box

[Pillhead]

might go for it then!

cheers

[mo.p]

hi m8 need your help how do find if they got v3 chip in them plzzz any help/info would be greatly appreciate

[Pillhead]

if you mean me i have no idea?

[bighun]

both of my boxes have the v3 chip in them i flashed them both with the patched version of blackhole 2.0.6 any image up to blackhole 2.0.5b work without being patched but after that they have put a mac address check in the image all the clone boxes have the same mac number so all you get is a black screen after you flash 2.0.6 original

[mo.p]

hi m8 how do u tell if your boxes have the v3 chip in them plzzz any help/info would be greatly appreciate

[bighun]

most of the chinese suppliers tell what chip is in the box i am now looking at the cloud ibox 2 with the 600mhz chip in with the v3.2 chip

[MENTE SICULA]

@ bighun
when you find it... post here the seller
^^

[bighun]

most suppliers are quoting about $102 dollars delivered to the uk but they will not be ready for 2 weeks yet

[MENTE SICULA]

i'm waiting for better times
at 102$ i buy an vu+ solo v3.2 clone

[Stewieb]

both of my boxes have the v3 chip in them i flashed them both with the patched version of blackhole 2.0.6 any image up to blackhole 2.0.5b work without being patched but after that they have put a mac address check in the image all the clone boxes have the same mac number so all you get is a black screen after you flash 2.0.6 original

Hi new at all this, so would appricate if someone could confirm if it okay's ok for me to flash me box with the 2.0.06 image and the best way usb stick or serial cable. Dont really want to end up with a door stop.



Cheers,

Stewart

[bighun]

flash it with the patched 2.0.6 image from the ferrari team it works good just format your usb stick in fat32 put the vuplus folder on your stick switch your box on your blue light will go sort of pinky blue then it will go to red and then flashing blue switch of your box remove usb then restart your box takes a wee while to do but it is a good image i prefer blackhole myself compared to all the other images

[RuberDuck]

Appear on AliExpress as the sale has not yet appeared in the Chinese say Officially Supported by OpenPLi, OpenAAF and the ViX Team and how we see that first to see if the price is competitive ....

you'd dead wrong there, while the ViX image may run on these clones ViX will never offer support of any kind for any cloned receiver. If and when things go pear shaped you'r on your own.

[RuberDuck]

are they really supported officially ?

Thanks

Not from ViX and never will be.

[bighun]

there will always be patched images for the clone boxes be it vix or blackhole

[RuberDuck]

there will always be patched images for the clone boxes be it vix or blackhole

Indeed but there will never be any official support from ViX for any clone and those who choose to put ViX on a clone will get no support at all if and when things go wrong.

[pa2]

Thats for sure why would vix support clone:eviltongue:

[MENTE SICULA]

Openspa, Openpli, VTI, BlackHole, VIX, Sif koala and much more... no one support clone vu+ and ban member in their forum is someone talking about !!
(of course of these images we can find all patched for clone)

Only one imagine is developed for vu+ clone: Vu Solo DE-OpenBlackHole by ToySoft

[RuberDuck]

Openspa, Openpli, VTI, BlackHole, VIX, Sif koala and much more... no one support clone vu+ and ban member in their forum is someone talking about !!


as is their rite, clones are dangerous, poorly made and a false economy. ( just my personal opinion ).

[Stewieb]

flash it with the patched 2.0.6 image from the ferrari team it works good just format your usb stick in fat32 put the vuplus folder on your stick switch your box on your blue light will go sort of pinky blue then it will go to red and then flashing blue switch of your box remove usb then restart your box takes a wee while to do but it is a good image i prefer blackhole myself compared to all the other images

Thanks all went will love the image and this little box seems to run great. One question my fans a little loud, any recommendations on a replacement?

Many thanks,

Stewart.

[MENTE SICULA]

replace it with one to 120mm or 80mm
silent fan | eBay (http://www.ebay.com/sch/i.html?_trksid=p2050601.m570.l1313.TR3.TRC1.A0&_nkw=silent+fan&_sacat=0&_from=R40)

[Pillhead]

flash it with the patched 2.0.6 image from the ferrari team it works good just format your usb stick in fat32 put the vuplus folder on your stick switch your box on your blue light will go sort of pinky blue then it will go to red and then flashing blue switch of your box remove usb then restart your box takes a wee while to do but it is a good image i prefer blackhole myself compared to all the other images

You got a link to that image please matey ? My box should be turning up tomorrow

Sent from my GT-I9505 using Tapatalk

[MENTE SICULA]

Here:
http://www.digital-kaos.co.uk/forums/f188/vu-solo-blackhole-2-0-6-ferrari-v2-toysoft-372208/

[Pillhead]

Thanks mate, i received mine today. This is a picture of the one ive received.

Do i still have to worry about this over heating? i dont want to switch it off everytime im not using it.

Also i have to say they have quite a high price tag for a build quality like this. The alien 8900 seems to be a better quality and is housed in a metal chassis rather than plastic.

Never seen a sat box housed in plastic before.

226244

Edit got mine plugged in just out of the box in my office and the heatsink under the fan is already to hot to the touch after about a hour and its not even doing anything!

Serious doubts about this box!? already!

[bighun]

don`t worry about the heat as long as the fan is working it will keep the box within tolerances they do get a wee bit hot but nothing serious i have ben running my cloud ibox 24/7 for the last 4 months without a single problem it is a good wee box for the money

[Pillhead]

what image are your running mate? im gonna get mine up and running tonight. hopefully........

Just cant believe they made it out plastic!

although the components are branded samsung and toshiba on board the pcb but they could be faked as well i guess!

[mickmc68]

Hi m8 i run the latest Vix image on mine and use a 1gb usb pen for cross epg , picons ect and the usb for the swap file , they are not a bad box i run my 1s upside to let the heat escape better and i swapped the fan for a silent fractual 1 .. though considering i purchased mine for abt ?45 each id say your owed something back from your surplier

Mick

[lombard]

i had one of the mini solo , with fan attached, ending up getting a better bigger fan, i have it up the normal way and runs fine, i have had openpl 3.0 running with all plugins, picons, epg for few months no issues at all, though vix 3.0 seems to crash slow down after 1-2 days, but openpli 3.0 had running for months no issues, i am looking forward to the ibox 2 , as its metal , 600mhz 1gb flash, 1gb ram, thing should fly

[Pillhead]

Hi m8 i run the latest Vix image on mine and use a 1gb usb pen for cross epg , picons ect and the usb for the swap file , they are not a bad box i run my 1s upside to let the heat escape better and i swapped the fan for a silent fractual 1 .. though considering i purchased mine for abt ?45 each id say your owed something back from your surplier

Mick

WEll i paid ?85 for my amiko box in december last year. On ebay most sellers are selling these boxes for over ?100 so i thought it was fair.

To be honest would you expect a ebay seller to honor a years warranty with no questions asked anyhow?

Im just pleased i didnt lose out completely.

Im using the black hole image that was posted above........

Anyone know the default user/pass?

[bighun]

i am using blackhole 2.0.6 by ferrari team running perfectly using all the plugins tspanel tsmedia autobouquets e2

[Pillhead]

where do you get all the plug ins from? there are so many options its a bit daunting at the moment!

So far ive got it all going on FTA channels but im unsure what cam to use? or where to download it from?

Downloaded ccam 2.1.3 and got the encrypted channels working now as well:)

But my ecm time says -nan??? i have no idea what that means??

Loving it now even though it is plastic.

Mine is uber responsive, fast in every way. Picture quality looks better than my dm800 and alien 8900...

Should i save cross epg and picons to the usb or internall now?

Anyone got rats bouqet and picon updater working?

[bighun]

you will get autobouquets here http://www.digital-kaos.co.uk/forums/f216/autobouquets-e2-28-2e-plug-296869/ also tspanel here.................................also tsmedia..................................... use vucc and ftp them to the tmp folder then install them using menu addons manually install ipk packages once you install autobouquets press green button press menu go to local area selection put in hd area you are in then press green to install takes a wee while to do but it puts all the channels in the same numbers as sky you will need to register with the forums to download the stuff


Do not post links to other forums with similar content

[Pillhead]

thanks i was trying to get rats updaters working for his bouquet and picons like i have on my dm800.

How ever all the link you just sent me install but auto bouquet just green screens when i try and update:( any ideas?

I was going to set up cross epg to my usb stick and picons on there, and i think some one mentioned putting a swap file partition or something on there?

Be nice to get it all going tonight but im getting tired now:(

Also be nice to get IPTV updater working as well but alas that wont install either

[bighun]

you will get iptv in tsmedia when installing autobouquets have you done a scan for channels if you have press up arrow then yellow select bskyb press ok then try installing autobouquets

[digicon]

The TSmedia plugin can be found on this very forum: http://www.digital-kaos.co.uk/forums/f207/tsmedia-enigma2-plugin-332694/ without having to link to others

[Pillhead]

IPTV updater is far superior and has a much better selection and adds them to your bouquet. How ever i cant get that to work or Autobouquets....

For now ive given up and will carry on trying tomorrow:)

[Pillhead]

Woke up this morning and box wouldnt turn on. had to un plug it from mains and back in again.

Hope it was just a one off .

[bighun]

i leave my box on 24/7 not caused any problems with heat

[Pillhead]

well i turned mine upside down and the heatsink was cool to the touch with the factory fan.

how ever turned the other way it was scorching, although my dm800 tuner is like that after 5 mins:D

I might try and mod it im not sure yet i just want to find a stable image where the plug ins that i want will run, mainly rats bouquet updater,rats picons updater and IPTV updater. OH and iplayer and itv player which run lovely on my DM800

[Pillhead]

My box seems fine when im using it but i turn it to standby some times it wont restart or when i come back to it it has crashed and needs to be unplugged and back in again before it will work.

Also the remote is very sluggish until a few mins after the image has booted?

Not sure whats going on as nothing has happened when im actually using the thing.

[lombard]

anyone ordered the ibox 2 yet ? thanks

[djrikstar]

Has anyone had the issue with the box not flashing its just a blue light and no display tried different images but just turns from red when i switch on, then straight to blue and does nothing. I have a m8 who has same issue. Anyone know of a fix or the right software to use on them to flash via serial? As tried many times to do with a usb it as if it doesn't recognize the usb no purple light

[digicon]

Has anyone had the issue with the box not flashing its just a blue light and no display tried different images but just turns from red when i switch on, then straight to blue and does nothing. I have a m8 who has same issue. Anyone know of a fix or the right software to use on them to flash via serial? As tried many times to do with a usb it as if it doesn't recognize the usb no purple light

Have you tried any different USB sticks just in case the one your using the box does not like

[Pillhead]

Im using a vix image now and its been stable for a few days. when it works its lightening fast! only thing id be happier with is a cool running box and a proper sub forum for cloud ibox with images and plug ins rather than keep trying ones from a vu solo which a lot of dont work.

[MENTE SICULA]

if someone want try... this is the last
Vu+ Solo : BlackHole 2.0.7 Ferrari V3 by Toysoft (https://mega.co.nz/#!OFNhUDII!W5a30kZu4leOZLQak2BsBG2NNnwS3rQjntUflKF zFCM)

Blue Menu fix, use Ferrari Addon Manager,

1) Go to FAM Plugin on BlackHole 2.x.x

http://www.8a8f8.com/gallery/4/full/11836.jpg

2) Select Fix

http://www.8a8f8.com/gallery/4/full/11837.jpg

TS

[lombard]

Im using a vix image now and its been stable for a few days. when it works its lightening fast! only thing id be happier with is a cool running box and a proper sub forum for cloud ibox with images and plug ins rather than keep trying ones from a vu solo which a lot of dont work.

the thing is it is a clone of vu solo , the newer updates of images dont work, as vu have updated the drivers to stop working on clones, just stick to slightly older images or get patched , i have had no issues plugins working , if it works on vu solo it will work on these

[bighun]

i am using a cloud ibox and have just put the new blackhole 2.0.7 by ferrari and it is working perfectly

[dale1983]

I'm currently using vix and has been running perfectly for the past 4 weeks. Plugins etc all work great :)

[Pillhead]

sent you another email dale:)

[lombard]

I'm currently using vix and has been running perfectly for the past 4 weeks. Plugins etc all work great :)

what build of vix 3.0 ? tried few different builds, never used to last after 1 day of use, other hand openpli 3.0 had no issues , rock solid and stable

Thanks

[Pillhead]

ill go through the settings and see if i can see.

[Pillhead]

from webif



Software


Kernel version:
3.1.1


Firmware version:
3.0


Gui version:
2012-08-14

[lombard]

from webif



Software


Kernel version:
3.1.1


Firmware version:
3.0


Gui version:
2012-08-14



Hi, that doesnt give anything

Menu button, Information , About, Look for Build ??? this tells you what build of vix 3.0 your using

i had enough of this box anyway, got it working stable on openpli 3.0 and sold it , so doesnt matter about info mate

[dale1983]

pm me your email lombard and i will send you the vix 3.0 back up image im currently using

[lombard]

pm me your email lombard and i will send you the vix 3.0 back up image im currently using

its ok mate, i have since sold it, i have the ibox 2 on order now , 500mhz , 1gb flash, 1gb ram, no heat issues, takes latest vix 3.0 build , openpli 4.0, cant wait to try it

[MENTE SICULA]

..i have since sold it, i have the ibox 2 on order now , 500mhz , 1gb flash, 1gb ram...

where you buy it?
tnx

[bighun]

both myself and lombard bought our cloud ibox2 here Cloud Ibox 2 600mhz Linux Os Full Hd With Iptv Support 3d Wifi Satellite Tv Receiver For Christmas Day Gift - Buy Cloud Ibox 2 600mhz,Cloud Iboxii 2 Iptv Support 3d Wifi Satellite Tv,Cloud Ibox Ii Linux Os Full Hd With Iptv Product on Alibaba.com (http://www.alibaba.com/product-gs/1331880932/cloud_ibox_2_600Mhz_linux_os.html)

[thebox]

Anyone posted any backups ?thanks

[Pillhead]

both myself and lombard bought our cloud ibox2 here Cloud Ibox 2 600mhz Linux Os Full Hd With Iptv Support 3d Wifi Satellite Tv Receiver For Christmas Day Gift - Buy Cloud Ibox 2 600mhz,Cloud Iboxii 2 Iptv Support 3d Wifi Satellite Tv,Cloud Ibox Ii Linux Os Full Hd With Iptv Product on Alibaba.com (http://www.alibaba.com/product-gs/1331880932/cloud_ibox_2_600Mhz_linux_os.html)


looks very cheap, i might go for one myself:) do you just message the people and they get back to you?ive never bought like this before.

[bighun]

yes lily airsat gives you an email address to make your paypal payment to once that is done you message her through alibaba and give her your email and home address also your paypal transaction id

[kkkklaur]

New model Cloud ibox 2 search in GOOGLE toolbar.................... L&W Aliexpress

[Pillhead]

would love to know what these are like!!??

[lombard]

i should get mine on tuesday if all goes well, i think people will start getting these over next week, then can start to play with them :)

[bighun]

my box left hong kong last night with a bit of luck it should be with me next tuesday or wednesday then the fun will start it is coming with dhl is that the same as you lombard

[lombard]

my box left hong kong last night with a bit of luck it should be with me next tuesday or wednesday then the fun will start it is coming with dhl is that the same as you lombard

Hi, no mines with fedex even though i requested DHL but tracking says should get on tuesday, also i dont know if image will use the full flash avalible or ram, as its based on the xp1000 receiever , it uses its images and that box is lower ram and flash, also its not 600mhz its 501mhz

[kkkklaur]

Is time to open new topic --CLOUD IBOX 2 ENIGMA 2 CLONE--- for not mixed answers with cloud ibox solo clone.

I open topic.....................................

This receiver successfully enthusiasts and users on the new topic

[bighun]

my box is out for delivery todaY I will keep you posted how it goes

[vipersvcd]

Hi all ,. can you please explain what Images are you installing to this Box (Cloud IBOX2 600MHZ) and where to download ?
In this video Cloud Ibox 2 HD Sat Receiver auf VU+ Solo Basis - Test Review (german/deutsch) - YouTube (http://www.youtube.com/watch?v=ROlFVY5h5v4) the person is running BlackHole , but someone here said it can not install black hole because it just for VU , can I download original images or do I need speciial patched images ?
Can I download directly from here......................................... ?
Should I choose VU+ Solo or OCTAGON-SF8-HD-XP1000?
I found this site but its quite empty :.....................................

Also which chip will better for streaming with TSMEDIA ,does one chip offer better GSTreamer video decoding codec support with over the other ?

Thanks ,

[lombard]

Hi all ,. can you please explain what Images are you installing to this Box (Cloud IBOX2 600MHZ) and where to download ?
In this video Cloud Ibox 2 HD Sat Receiver auf VU+ Solo Basis - Test Review (german/deutsch) - YouTube (http://www.youtube.com/watch?v=ROlFVY5h5v4) the person is running BlackHole , but someone here said it can not install black hole because it just for VU , can I download original images or do I need speciial patched images ?
Can I download directly from here........................ ?
Should I choose VU+ Solo or OCTAGON-SF8-HD-XP1000?
I found this site but its quite empty :........................................

Also which chip will better for streaming with TSMEDIA ,does one chip offer better GSTreamer video decoding codec support with over the other ?

Thanks ,

that video is a clone of a vu solo in a shell looking like a dm800se, so yes it will take blackhole images, as vu solo does

[vipersvcd]

That is clearly an ibox2 in a dreambox case.

[tappy]

I've had my Cloud iBox (original) for 4 weeks now and I'm chuffed with it.

I replaced the fan with this as it was too noisy: Mini Kaze, 40mm x 10mm Quiet Cooling Fan (http://www.quietpc.com/mini-kaze)

I removed the card reader and shorted pins 5 and 6 with a HDD jumper (http://www.ebay.co.uk/itm/2-Pin-HDD-Jumpers-Fits-Maxtor-Samsung-CD-DVD-HDD-IDE-/160762022860?pt=UK_Computing_Other_Computing_Netwo rking&hash=item256e29cbcc). I found that if you don't do this, you'll see a lot of crashes.

I leave the lid on but keep the box upside down. It runs cool and silent.

I'm running VIX 3.0.761 VU+ Ferrari V3a and it never crashes. I leave it on 24/7.

I've got lots of plugins installed (cacheflush, mediapanel, tsmedia) and all work without any issues. I've also installed the MetrixHD skin and that works and looks great.

I've setup a swap file to help but I'm not sure it's needed.

I paid ?60 for my box and it's an absolute bargain.

[MENTE SICULA]

... I removed the card reader and shorted pins 5 and 6 with a HDD jumper (http://www.ebay.co.uk/itm/2-Pin-HDD-Jumpers-Fits-Maxtor-Samsung-CD-DVD-HDD-IDE-/160762022860?pt=UK_Computing_Other_Computing_Netwo rking&hash=item256e29cbcc). I found that if you don't do this, you'll see a lot of crashes. .. can you post a photo of this? tnx


Is time to open new topic --CLOUD IBOX 2 ENIGMA 2 CLONE--- for not mixed answers with cloud ibox solo clone.

I open topic.....................................

This receiver successfully enthusiasts and users on the new topic

where is?

[bodyzlam]

Anyone use Cocobox M3(cloud ibox upgraded with metalbox bigger size and no more heat problem,seller said)?

Does anyone have some information about it? I google it but I found not much :(


(sorry my english)

[tappy]

can you post a photo of this? tnx
http://i40.tinypic.com/2iustb9.jpg

[armstrongstreener]

Anyone wanting to update to my patched openpli 4.0 image. http://www.digital-kaos.co.uk/forums/f187/vu-solo-cloud-ibox-openpli-4-0-patched-v3-safe-backup-382361/#post2150394

[gregorke]

Hiya,


Unable to update via dcc please and u give mr login details, this image looks really good though!

[armstrongstreener]

update via usb. login details:

user: root
pass: blank

enjoy and leave feedback thanks

[kkkklaur]

that video is a clone of a vu solo in a shell looking like a dm800se, so yes it will take blackhole images, as vu solo does

IS a clone a VU +SOLO (CLOUD IBOX )

NOT A CLOUD IBOX 2 (motherboard)

use a metal case and a big fan to a Dreambox 500hd

Receiver made a SHENZEN HUAZART .....CHINA

A good idea for a few dollars difference is not significant and better cooling, and better design.

[kkkklaur]

http://i40.tinypic.com/2iustb9.jpg
To remove noise can enter the supply fan with a resistance value between 60 ohm/3w.......100ohm/3w by cooler large cooler if they put 100 s ohm/3w if is small and if put a lower value is by sounding cooler so just be warm seams are isolated do not contact any one component on the board. Noise is unnoticeable and decreases fan wear

[Pillhead]

anyone cloud i box 2's turned up yet?

[Fuse100A]

I removed the card reader and shorted pins 5 and 6 with a HDD jumper (http://www.ebay.co.uk/itm/2-Pin-HDD-Jumpers-Fits-Maxtor-Samsung-CD-DVD-HDD-IDE-/160762022860?pt=UK_Computing_Other_Computing_Netwo rking&hash=item256e29cbcc). I found that if you don't do this, you'll see a lot of crashes.
What kind of crashes you say? He goes to Green screen (crashes of Enigma) or unstable work of softcam?
I removed the card reader but pins still unlocked. It works fine (Cloud Ibox+OpenPLi 4 ferrari v3a+upgrades up to this day from OpenPLi feed). But sometimes have to restart a softcam(mgcamd1.38c). May be a shorted pins (5 and 6) is solve my problem?
Thanks!
P.S.: What is the name of security chip? In the picture is difficult to see its name... STM8510 or...? Or take his picture in macro-mode, please. Thanks!

[kkkklaur]

What kind of crashes you say? He goes to Green screen (crashes of Enigma) or unstable work of softcam?
I removed the card reader but pins still unlocked. It works fine (Cloud Ibox+OpenPLi 4 ferrari v3a+upgrades up to this day from OpenPLi feed). But sometimes have to restart a softcam(mgcamd1.38c). May be a shorted pins (5 and 6) is solve my problem?
Thanks!
P.S.: What is the name of security chip? In the picture is difficult to see its name... STM8510 or...? Or take his picture in macro-mode, please. Thanks!


Use image open AAF 12 08 2013 install TSpanel plugin remove unecesary plugin install plugin "CACHEFLUSH" look---- AFTER RUN CACHE FLUSH plugin it most you have 20-30 % free memory
use cccam 2.3.0

op

for SD TELEVISION (OLD TUBE TV) is must install only SD SKIN i use MAGIC SD skin for SD TV

use only skin for our resolution TV SD, XD, ..HD

Skin size: SD: 720x576px - XD: 1024x720px - HD: 1280x720px

For edit and remove unnecesary chanelor or sattelite channel use DogSettings 1.6.0.0 ( download source dreambox.it) search in Tools menu

[scottyboyz]

anyone cloud i box 2's turned up yet?

My cloud ibox 2 arrived and its not based on the VU+ solo. It seems cloud ibox 2 is max digital xp1000 clone. It comes with openpli 4.0 pre installed and updates seem to work. Pretty impressed with it to be honest. Much better design than the cloud ibox1.

I will say this though before someone else tries it. It wont accept any PLI / VIX images from there website so im guessing some clone patched images will arrive soon. I flashing various images and it just bricks the box with red light. Luckily i saved my original firmware and just reflashed it back.

Thought i would just give the heads up before many more try updating it to vix or some other xp1000 firmware.

[brommapojkar]

Mini Vu + solo, stopping at a red light, what do I need to do to get thego ig?ng.Hj?lp me please. sorry google translate:joyous:

[cormacodonnell]

My cloud ibox 2 arrived and its not based on the VU+ solo. It seems cloud ibox 2 is max digital xp1000 clone. It comes with openpli 4.0 pre installed and updates seem to work. Pretty impressed with it to be honest. Much better design than the cloud ibox1.

I will say this though before someone else tries it. It wont accept any PLI / VIX images from there website so im guessing some clone patched images will arrive soon. I flashing various images and it just bricks the box with red light. Luckily i saved my original firmware and just reflashed it back.

Thought i would just give the heads up before many more try updating it to vix or some other xp1000 firmware.


i got a 3.0.600 openvix image running on it with cccam - small issue with updating bouquets through dreambox editor though....also Dont know if the image is patched in any way - can get it from cloud-ibox2 dot com

[kkkklaur]

can you post a photo of this? tnx



where is?

Moderators close topic cloud ibox 2 because exist a post

[kkkklaur]

Today post a diference in a ORIGINAL CLOUD IBOX 1 and CLONE CLOUD IBOX 1



cloud ibox 1 is not ferrari clone receiver

for original receiver security chip is erased and has no oval metal piece next chip

http://imageshack.com/a/img22/3121/nem4.jpg

CLOUD IBOX 1 new image software

OPEN PLI 4 beta with password cracker plugin:

http://www.fileshare.ro/e30025282

http://www.datafilehost.com/d/4bf9a7a1

how to install
after instal software go to plugin>software manger>plugins >install extension>
restart GUI
Go to plugins" John the ripper" remove pasword

after go to DCC and after the COMPLETE conection FTP AND TELNET use pasword ..... dreambox..... and ......good luck
-------------------------------------------------------------------------------------------------------------------
For the future use FERRARI Vu+ Solo software the V2a or V3a modified images,for cloud ibox 1

Edit channel or download new bouquet or sattelite use EDITOR DOG SETTINGS 1.6.0.0
http://www.datafilehost.com/d/31a599be

[kazaaman]

anyone cloud i box 2's turned up yet?

I have 10 of these, all flashed with vix software & worked ok but had 2 switched off picture after 20 minutes though blue light stays on so a bit of investigation, have sold 4 of them so far & have 1 at home, all hooked up to 1tb ext hard drives & working rock solid, more stable than vu+ duo 3.2's at the moment.

[djpopeye1971]

how do i add mgcamd to it

[kkkklaur]

new image by gaga24

BlackHole-2.0.7.1-vusolo_usb_Ferrari_V3a.zip

http://www.easybytez.com/l2mu0c7lo0nu

What is New;

NEW NEW NEW Cross Epg 0.7 version by Andyblac
Update skin MX S Line
Update Open Webif
Update Vuplus-blindscan
Add support for ssh108 automatic scan
Update transtreamproxy
Update driver 20131106
Fix HDMI hotplug in standby(proc entry is also added)
Support DVB-T2 automatic scan(uno, ultimo, duo2)
Improve transcoding(duo2, solo2)
Add dst_apply proc entry
Increase demux number to 9(duo2, solo2, ultimo)
Support blindscan in all slots(ultimo, duo2)
Update driver 20131108
Support play/pause key of new Duo2 RC(solo/duo/uno/ultimo)
Update languages: da, fr, no, ru.

Don't forget to apply BH fix 2.x.x from Ferrari Addons Manager

[Pillhead]

new image by gaga24

BlackHole-2.0.7.1-vusolo_usb_Ferrari_V3a.zip

Download Black Hole vusolo usb Ferrari V3a zip (http://www.easybytez.com/l2mu0c7lo0nu)

What is New;

NEW NEW NEW Cross Epg 0.7 version by Andyblac
Update skin MX S Line
Update Open Webif
Update Vuplus-blindscan
Add support for ssh108 automatic scan
Update transtreamproxy
Update driver 20131106
Fix HDMI hotplug in standby(proc entry is also added)
Support DVB-T2 automatic scan(uno, ultimo, duo2)
Improve transcoding(duo2, solo2)
Add dst_apply proc entry
Increase demux number to 9(duo2, solo2, ultimo)
Support blindscan in all slots(ultimo, duo2)
Update driver 20131108
Support play/pause key of new Duo2 RC(solo/duo/uno/ultimo)
Update languages: da, fr, no, ru.

Don't forget to apply BH fix 2.x.x from Ferrari Addons Manager


is that for ibox one or ibox two? and is it easy to backup the image i already have and it generally runs like a dream

[digicon]

is that for ibox one or ibox two? and is it easy to backup the image i already have and it generally runs like a dream


That Image will be for the original iBox seeing as it is a Backup of Blackhole which will not run on the iBox2

[Siguiente]

Hello.

I have a problem with my cloud ibox. Tuner seems to be broken. It has signal, but it appears me at 0%. First time it happened, I changed the image and it was solved, but now it does not work with any image.

any ideas?

[johannst]

I just got my mini vu solo cloud ibox (http://www.st-box.com/index.php/mini-vu-solo-cloud-ibox-satellite-receiver.html) from china. I love it. The advice i got from this forum really helps. I turned it upside down and removed the CI. It stays cool and healthy. It came with black hole and i changed to openPLI 4.0. The price i paid for this stuff is about 1/9 of other boxes doing the same. ABSELOUT BARGAIN. I wach every channel on my ipad and i just love it. Thank you guys for a good forum.

[roadie]

Hi. Guys, I have bought one of these.. but I am struggling to use it, can anyone help?

[daviddrf]

Hi, I bought one one month ago and 'm very happy with it but I have two doubts:
?Is the clone's IR remote able to work as an universal remote like the original one and being able to control other TVs introducing its code?
?How can I make an image flash backup if this receiver is a clone and not original? I tried with BackupSuite but it tells me there's a problem with the kernel dump or someting like that...
Thank you and see you soon.

[imran999]

Which is the better box, looking for fast channel switching, and a good EPG.

I have ordered a skybox f5s to play with and looking to get a 2nd box for my parents. It needs to be easy to use with a simple interface.

Identified Cloud IBOX or the IBOX2...which is better?

Also seen this, Cloud ibox vu mini, is this the same as the ibox with a different name or different? High Quality Cloud ibox Enigma 3 Mini VU+ Solo Mini Vu+Solo DVB-S2 IPTV+Youtobe Streaming Channels Satellite Receiver (http://www.st-box.com/index.php/mini-vu-solo-cloud-ibox-satellite-receiver.html)

Also there now seems to be a v3 vu+ solo box...any idea what this is?

[kkkklaur]

CLOUD IBOX 1

latest softwares working all version

search with google

Ferrari_VU_Solo_download

open first link in rank and good luck
-------------------------------------------------------------------------------------

PLUGIN PACK ENIGMA 2

(inside is TSPANEL, TSMEDIA, CLARMEM, CLONE FERRARI ADDONS MANGER)

http://www.datafilehost.com/d/19d70df2

[billalahmed]

which vix version do you recommend? im using 3.0.708 but it freezes when epg updates automatically in the morning.

[lombard]

which vix version do you recommend? im using 3.0.708 but it freezes when epg updates automatically in the morning.

epg works fine for me, i use xmltv-importer to download epg

[billalahmed]

epg works fine for me, i use xmltv-importer to download epg

which version of vix u using? are you using vix 3.0.708?

[kkkklaur]

which version of vix u using? are you using vix 3.0.708?

VU+ Solo OpenVIX-3.0.664 Backup By Ten Below

[billalahmed]

VU+ Solo OpenVIX-3.0.664 Backup By Ten Below

??? is 3.0.664 working without any epg update problems

[kkkklaur]

For work without epg update problems is need to do a swap to a external USB stick and use plugin CLEARMEM or CACHE FLUSH for increase the memory space
try PERSIAN EMPIRE image

[billalahmed]

For work without epg update problems is need to do a swap to a external USB stick and use plugin CLEARMEM or CACHE FLUSH for increase the memory space
try PERSIAN EMPIRE image

Thanks, i'll try getting that plugin to see if that works.

[kkkklaur]

Last OPENAAF image (open pli core) software CLOUD IBOX 1
December 2013
work updates online


Download OPENAAF GOLD EDITION.rar (http://www.datafilehost.com/d/1adc692c)

Channel,satellite EDITOR

http://www.datafilehost.com/d/31a599be

Image is ready for use (BACKUP) have inside TSPANEL.TSMEDIA,FERRARI ADDONS MANAGER,WEATHER,CACHE FLUSH,
have ALL sattelites and bouqets inside xml files updated dec 2113, skin for SD (old TV) and HD TV
c........g folder is in etc

ALL information is only for educational use and Viewing Pay TV without a valid subscription is illegal !

[daviddrf]

Hello, one question. How can I do a flash backup image of this clone? See you soon.

[andyd123]

It will dpend which image you use but generally you can use a plugin called backup suite to backup.

[carbandit]

:joyous:Last OPENAAF image (open pli core) software CLOUD IBOX 1
December 2013
work updates online


Download OPENAAF GOLD EDITION.rar

Image is ready for use (BACKUP) have inside TSPANEL.TSMEDIA,FERRARI ADDONS MANAGER,WEATHER,CACHE FLUSH,
have ALL sattelites and bouqets inside xml files updated dec 2113, skin for SD (old TV) and HD TV
c........g folder is in etc

put in this to my box and works great but cant get my epg to show ..any ideas guys in what im doing wrong ...many kind regards and all the best for xmas


edit got it sorted

[kkkklaur]

clear mem with CACHE FLUSH PRESS BLUE BUTTON ( CLEAR)

for use EPG for many channnel need to use swap partition to external usb stick because EPG consume memory for all software images an for all types receiver, and is posible to freeze software is not a bug is a memoy hardware capabilities for this receiver....

[daviddrf]

It will dpend which image you use but generally you can use a plugin called backup suite to backup.
Thank you very much! It worked fine with the last BackupSuite version from the last page of this post: BackupSuite - [EN] Enduser support - Forums (http://openpli.org/forums/topic/21460-backupsuite/)
Now I would like to know if the remote control of this clone is universal and if is it able to control your TV like the original one because I tried to configure it as an universal remote but I wasn't able to. Thank you again and goodbye!

[andyd123]

As far as I know these remotes only control the box nothing else.

[kkkklaur]

Cloud ibox 1 (VU Solo clone) era finish appear new chinese clone
Vu Duo Mini (X DUO)

Prcessor 405Mhz MIPS (1CORE) ,HDD sata ,PIP, Dreambox metal case with big fan,exteral power supply

[redondo5]

Well i finally got a fracture fan installed and put vix CE image on... And it rock solid and running relatively cool. Got 16gb tiny flash stick sandisk for ?7 and setup picons and epg on it.

Now to see what this duo mini is ...

[daviddrf]

Holly sh...hotFree ship VU Solo2 Satellite HD Receiver-in Satellite TV Receiver from Consumer Electronics on Aliexpress.com (http://www.aliexpress.com/item/hotFree-ship-VU-Solo2-Satellite-HD-Receiver/1601496675.html)

[spycrab101]

Holly sh...hotFree ship VU Solo2 Satellite HD Receiver-in Satellite TV Receiver from Consumer Electronics on Aliexpress.com (http://www.aliexpress.com/item/hotFree-ship-VU-Solo2-Satellite-HD-Receiver/1601496675.html)

No feedback And stolen pictures, seems like a scam to me.

[daviddrf]

No feedback And stolen pictures, seems like a scam to me.

It could be...yes...

[spycrab101]

I won't be the one taking a punt :p maybe someone could ask him to send pictures of the motherboard or something.

[redondo5]

Definitely a scam... Steer clear.

[carbandit]

check out his name ...nic i am :eviltongue: mabye chinese yoda

[RealtimeX]

I wonder how risky it actually is dealing with seemingly shoddy sellers? Isn't Aliexpress's escrow payment system supposed to protect the buyer from scams?

[daviddrf]

check out his name ...nic i am :eviltongue: mabye chinese yoda

Haha, chinese yoda lol...

[spzjulien]

new image by gaga24

BlackHole-2.0.7.1-vusolo_usb_Ferrari_V3a.zip

Download Black Hole vusolo usb Ferrari V3a zip (http://www.easybytez.com/l2mu0c7lo0nu)

What is New;

NEW NEW NEW Cross Epg 0.7 version by Andyblac
Update skin MX S Line
Update Open Webif
Update Vuplus-blindscan
Add support for ssh108 automatic scan
Update transtreamproxy
Update driver 20131106
Fix HDMI hotplug in standby(proc entry is also added)
Support DVB-T2 automatic scan(uno, ultimo, duo2)
Improve transcoding(duo2, solo2)
Add dst_apply proc entry
Increase demux number to 9(duo2, solo2, ultimo)
Support blindscan in all slots(ultimo, duo2)
Update driver 20131108
Support play/pause key of new Duo2 RC(solo/duo/uno/ultimo)
Update languages: da, fr, no, ru.

Don't forget to apply BH fix 2.x.x from Ferrari Addons Manager


this image is working great on my icloud box 1 .... best image so far

[spzjulien]

ah i talk too fast i have freezing with my icloud box ..... with BlackHole-2.0.7.1-vusolo_usb_Ferrari_V3a


now im testing BlackHole-2.0.8-vusolo_usb_Ferrari_V3.zip - 55.4 MB (http://uptobox.com/dl5ht7og87h9)



it seem problem gone with 2.0.8 no freeze since 6h running, instead of 2.0.7 was keeping freezing a lot

very happy and nice new skin and other new stuff on 2.0.8

[kkkklaur]

Soon....Air digital SHENZEN made this......

CLOUD-IBOX 3
FEATURES: -
• Linux Operating System
• Multimedia plug-in supported
• HDMI up to 1080p
• 1 x Smartcard-Reader
• 2 x USB2.0
• USB WiFi internal (optional)
• 100 Mbit Ethernet Interface
• Advanced EPG (Electronic Program Guide)
• Full automatic service scan
• Various OSD skins supported
• Cool silent fanless running
• Low deep-standby power consumption under 1 W
Specification: -
• HDTV Receiver MHEG-2/4 H. 264
• 3D Ready
• CPU500 MHz BCM MIPS Precessor Linux OS
• Excellent sound quality in Dolby Digital
• 2x TUNERS DVB-S/S2+T2/C Sat Tuner built-in
• HDMI Connection
• Scart Connection
• USB PVR Support of external HDD (HDD Optional)
• 1xCardreader
• 2x USB 2.0
• Ethernet access 10/100 Mbit
• 512MB Flash / 512MB DDR3
• USB Port for adding PVR funtions and more...
• Timeshift
• Electronic TV programmes ( EPG )
• Parental Control
• Plugin Service
• OSD into many languages and graphics (Skins)
• Webinterface, WEB Remotcontrol
• DISEqC 1.0, 1.1, 1.2, 1.3 and USAL's
• External power supply12V 3A
Supported by OpenPLi, OpenATV and the ViX Team, including free iptv streaming, american, brazil, arabic, Russian, Asian,english movie, live sports streaming.

[oribman]

Hi, I purchased today a Cloud Ibox from a chinese supplier, and I started reading about the chip version and other related things, but the more I read the more I got confused about this chip version. For example these two posts seem contradicting:
http://www.digital-kaos.co.uk/forums/f184/openbox-s6000hd-upgrade-guide-sharing-setting-up-guide-338992/#post_message_1972118
http://www.digital-kaos.co.uk/forums/f184/openbox-s6000hd-upgrade-guide-sharing-setting-up-guide-338992/#post_message_1987335
I want to know if Cloud Iboxes or Openbox s6000 HDs do have a ferrari chip or whatever it's called at all and if yes how to tell which version they have?

[spzjulien]

Soon....Air digital SHENZEN made this......

CLOUD-IBOX 3
FEATURES: -
• Linux Operating System
• Multimedia plug-in supported
• HDMI up to 1080p
• 1 x Smartcard-Reader
• 2 x USB2.0
• USB WiFi internal (optional)
• 100 Mbit Ethernet Interface
• Advanced EPG (Electronic Program Guide)
• Full automatic service scan
• Various OSD skins supported
• Cool silent fanless running
• Low deep-standby power consumption under 1 W
Specification: -
• HDTV Receiver MHEG-2/4 H. 264
• 3D Ready
• CPU500 MHz BCM MIPS Precessor Linux OS
• Excellent sound quality in Dolby Digital
• 2x TUNERS DVB-S/S2+T2/C Sat Tuner built-in
• HDMI Connection
• Scart Connection
• USB PVR Support of external HDD (HDD Optional)
• 1xCardreader
• 2x USB 2.0
• Ethernet access 10/100 Mbit
• 512MB Flash / 512MB DDR3
• USB Port for adding PVR funtions and more...
• Timeshift
• Electronic TV programmes ( EPG )
• Parental Control
• Plugin Service
• OSD into many languages and graphics (Skins)
• Webinterface, WEB Remotcontrol
• DISEqC 1.0, 1.1, 1.2, 1.3 and USAL's
• External power supply12V 3A
Supported by OpenPLi, OpenATV and the ViX Team, including free iptv streaming, american, brazil, arabic, Russian, Asian,english movie, live sports streaming.


since i order icloud ibox 2 from them, got so much trouble, i will never order again from them, since they dont care abt customer support ... and dont answer mail, when they got money from you ....

[kkkklaur]

since i order icloud ibox 2 from them, got so much trouble, i will never order again from them, since they dont care abt customer support ... and dont answer mail, when they got money from you ....



sellers with good rating is

aliexpress site search

yojia
l&w

Shenzhen Air Digital makes motherboards for planting that has automatic line and receivers and parts and make the rest of the poor vendors with small shops that put pictures of the factory in Shenzen factories to see what her clients and the receiver marked "AIR" others give their own reviews on the Chinese all over the world ..... looking good rating and sales stores over 1000 pcs ...

[spzjulien]

they suxx ... and for sure u work for them
they sell unfinished products with false info like the icloud ibox 2 ... i order one ... they say smartreader was include and 2 usb, there was no smartreader and only one usb, and i dont talk abt 600mhz CPU... and other fake info, i conttact them explain them that i need smartreader, they ingnore me, and now they start selling icloud ibox 3, so funny.......they are liar stay away from them ... you can find better seller for same price in aliexpress

i RE-sold my icloud box 2, it was not good unfinished product

[digicon]

they suxx ... and for sure u work for them
they sell unfinished products with false info like the icloud ibox 2 ... i order one ... they say smartreader was include and 2 usb, there was no smartreader and only one usb, and i dont talk abt 600mhz CPU... and other fake info, i conttact them explain them that i need smartreader, they ingnore me, and now they start selling icloud ibox 3, so funny.......they are liar stay away from them ... you can find better seller for same price in aliexpress

i RE-sold my icloud box 2, it was not good unfinished product


As with any Cloned product since the start of the Fake rolex many years ago you pay your money and you take a chance, If you want peace of mind then you buy Original products only with warranty and dealer support

[spzjulien]

As with any Cloned product since the start of the Fake rolex many years ago you pay your money and you take a chance, If you want peace of mind then you buy Original products only with warranty and dealer support

or u can buy from another trusted dealer on aliexpress ... but not this one

[spzjulien]

ah i talk too fast i have freezing with my icloud box ..... with BlackHole-2.0.7.1-vusolo_usb_Ferrari_V3a


now im testing BlackHole-2.0.8-vusolo_usb_Ferrari_V3.zip - 55.4 MB (http://uptobox.com/dl5ht7og87h9)



it seem problem gone with 2.0.8 no freeze since 6h running, instead of 2.0.7 was keeping freezing a lot

very happy and nice new skin and other new stuff on 2.0.8


new update after fews days testing 2.0.8 working great, only had one freeze when my cardreader was disconnected, since i reconnect it ... no more freeze, and the box keeping cool and not warm .... best rom so far for me ....

[skybandit]

Has anyone tried one of these?

What's the buold quality like. Being sold on flea bay as a solo clone enigma 2 receiver.

Linux Receiver | eBay (http://www.ebay.co.uk/itm/Enigma-2-receiver-vu-solo-dreambox-linux-satellite-receiver-/330842324905?_trksid=p2047675.m2109&_trkparms=aid%3D555001%26algo%3DPW.CURRENT%26ao%3D 1%26asc%3D29%26meid%3D4218117357060531737%26pid%3D 100010%26prg%3D1013%26rk%3D3%26sd%3D190772217912%2 6)

I've been using one of these, although branded as an Openbox S6000HD, but sounds identical, for several months....

It works fine, although my only problem is getting to know how to use it, ie understanding Enigma2, Blackhole and how to set it up properly to view the channels I want to watch. Still struggling to understand how to use things like satellites.xml and bouqutes etc...

[digicon]

I've been using one of these, although branded as an Openbox S6000HD, but sounds identical, for several months....

It works fine, although my only problem is getting to know how to use it, ie understanding Enigma2, Blackhole and how to set it up properly to view the channels I want to watch. Still struggling to understand how to use things like satellites.xml and bouqutes etc...

Then your first stop on this forum is to read the very informative Guides in the Enigma2 section as well as a few of the dreambox guides as they all apply

[Pillhead]

new update after fews days testing 2.0.8 working great, only had one freeze when my cardreader was disconnected, since i reconnect it ... no more freeze, and the box keeping cool and not warm .... best rom so far for me ....


if you disconnect the card reader you have to short out some pins on the board with a HDD jumper but i cant remember which ones! it was on here some where

[Pillhead]

to remove card reader safely (no freeze software) conect pin 5 and 6 ( numbering from any ditch 10-pin edge)motherboard card reader conector with a HDD jumper, CLOUD IBOX work no freeze only with fan to a chipset cooler best image no freeze and stable is OPENAAF(OPEN ATV) Ver 20130812 not new because new image interrogate MAC and black screen

this is the good image software stable ,and no freeze

openatv-3.0-vusolo-20130812_usb.zip

download here

DepositFiles (http://dfiles.eu/files/qevo1ql8l)

after instal the image download ccam (inside software conect to server and install) after instal ok and install c lines conect with ftp and instal in folder usr/keys/ccam.cfg


This information is only for educational use not use for view TV PROVIDER.
A good day...

im trying it now..................i counter from the bottom of the connector...........ie the pin nearest the outside of the case is no1..............

cheers

[Pillhead]

new update after fews days testing 2.0.8 working great, only had one freeze when my cardreader was disconnected, since i reconnect it ... no more freeze, and the box keeping cool and not warm .... best rom so far for me ....


short pins 5 and 6 out mate with a HDD jumper............

[Blitz101]

Guys i downloaded epg by mistake to internal flash! Is there a way to remove it?

[digicon]

Guys i downloaded epg by mistake to internal flash! Is there a way to remove it?


FTP over to the Box and you should see the File in with the other folders just delete from there

[Blitz101]

Thanks! Any idea the exact name if the file? Should I just delete it?

[digicon]

simple really the one that's called epg.dat

[Blitz101]

Ok thanks!! Will that then free a lot of memory?

[digicon]

Ok thanks!! Will that then free a lot of memory?


It will only free up what ever size the actual epg.dat is, your better storing the EPG on an external USB drive.

[ajax2061]

seams the ibox 3 is going to be a clone of the Xpeed lx2 without the VFD display

[blue boy]

Hi
I have a cloudIbox 2 with a fault and I am sending it back to the uk seller, he has advised that I should replace it with the first Cloud I box , he reckons that they are more stable, the heat issues are fixed and they can run any image, can anyone tell me if it is true that I can run any image on this box? I particularly liked the Vix 308 image that I had on faulty CloudIbox 2 that is to be returned.
Thanks for your help.

[singingshiver]

Hi
I have a cloudIbox 2 with a fault and I am sending it back to the uk seller, he has advised that I should replace it with the first Cloud I box , he reckons that they are more stable, the heat issues are fixed and they can run any image, can anyone tell me if it is true that I can run any image on this box? I particularly liked the Vix 308 image that I had on faulty CloudIbox 2 that is to be returned.
Thanks for your help.

I am running Vix 308 on an original Cloud Ibox without any issues for the last 2 weeks. Great box and image. I stayed away from the Cloud Ibox 2 as I read there were issues and a new main board was being introduced to correct the issues.

[Blitz101]

Anybody got latest vix 3.0 808 working image for this box they could pm me? Thanks:-)

[Blitz101]

Guys ,I have a problem with 2 New cloud iboxes both came with open pli, No matter what image i try and use they just wont show a pic after blue light flashes after the flashing process is finished! any ideas??? think ive tried both versions of chip now?? so im stuck!!!!!

[Pillhead]

Guys ,I have a problem with 2 New cloud iboxes both came with open pli, No matter what image i try and use they just wont show a pic after blue light flashes after the flashing process is finished! any ideas??? think ive tried both versions of chip now?? so im stuck!!!!!

have you tried other images.?

[Blitz101]

Yes! Tried a lot now!

[tkm18]

Yes! Tried a lot now!


Any joy with this, got two doing the same, tv is picking up a signal, but stays blank.

Tried numerous images, and cant update the chip, doesnty seem to find the box, using the cables and adaptor i used on my duo.

Nightmre.

[spzjulien]

latest image for cloud ibox

BlackHole-2.0.9-vusolo_usb_Ferrari_V3



OpenPLi-4.0-beta-vusolo-20140118_usb_Ferrari_V3a

[tkm18]

latest image for cloud ibox

BlackHole-2.0.9-vusolo_usb_Ferrari_V3



OpenPLi-4.0-beta-vusolo-20140118_usb_Ferrari_V3a


Any idea why some iboxs arent taking images properly, as in blank screens?

[spzjulien]

i just install blackhole 2.0.9 on my 2 X cloud ibox (chip v3) and not black screen so far ...... image working great

[dynomikered]

Hi do i need a boot file with the blackhole image as im getting the dreaded black screen after downloadin black hole 2.0.9
Thanks
Mike

[emad13]

hi guys thanks for this fantastic review of cloud ibox, unfortunately I also purchased one of these cloud ibox when I thought I was getting my self a genuine one.

I need help with installing TSmedia onit

am new when it come to this, so please take it easy and use words that will make sense to a newbie.

cheers
EMAD

[tnastar]

where can i download blackhole 2.0.9 for cloud ibox2

[bighun]

you will get it here Updates Cloud-Ibox Series - Index of: home/ (http://www.cloud-ibox.net/)

[ffgmat]

hi.
When I Disconnect the card reader my cloid ibox image is frozen from time to time (30min-1h). if anyone has soft that does not have such problem please give me know, I preferred openpli.Thanks

[xtsx]

IIRC you need to put a jumper between the middle two pins i.e. 5&6 on the port you removed the card reader from. I'm sure its out there on the web somewhere.