Bosch ME 7.1.1 helpME please !!!!!!!!!

[mauronow]

Hello friends! sorry for my bad english...
Please I need your help,

The car is a WV Vento (Jetta) 2.5 170 HP gasoline
I have read the file with galletto obd2, i read as golf 5 ME CAN 7.1.1.
The reading was in 32 minutes, READING OK.
Then I open the Titaniu m.. and detects the driver as I Vento 2.5 170 HP Perfect!
Then edit the file and upload it with galletto also.

-Now the car will not start, just turns but does not start the engine.
-I read with Galleto and gives me the info wrong data in info.
- As I put the ECU in boot mode to enter the file galletto who read the first time?
-The file is 1mb, titanium detected OK!
- I do not find as plug out of the car to enter the file good
Attached photo of the ecu and read the first file of 1 mb.
Can you help please? In the photos of galletto ecu not get this, is not equal to the photo. look good.:banghead::banghead::banghead:
In pinout galletto photos this ECU not there similar.
Thank you!

I hope answers ..

[k0mpresd]

me7 uses k line to flash. not canbus.
you only need 12v, ground, k line connection to ecu. flash in bootmode.
your original read seems bad.

[mauronow]

me7 uses k line to flash. not canbus.
you only need 12v, ground, k line connection to ecu. flash in bootmode.
your original read seems bad.

Thanks, but I have a photo of boot mode.
In galletto photos of cd, are not equal. good look at them.

file that you recorded =?

[k0mpresd]

pins are same as me7.5 bootmode. i have done these 2.5l me7.1.1 ecus before.
here is 150hp file. maybe you can at least recover in bootmode using this file.

[ominimicu]

ARE YOU SURE titanium corrected the checksum??

[filecloud]

Hello
This is ME7.1.1 ST10 ecu!! Will not write over OBD with clone tools. US models have checksum in processor active, so flash + processor must be tuned.
With attempt to OBD write you killed eeprom and maybe processor content.
greetings,
filecloud

[mauronow]

Hi I have 7.1.1 boot mode
Galletto2 reading OK !!
ID OK !

I need to charge an original file with galletto to revive the ecu with galletto
NO I have the full file.

[filecloud]

Hi I have 7.1.1 boot mode
Galletto2 reading OK !!
ID OK !

I need to charge an original file with galletto to revive the ecu with galletto
NO I have the full file.

Your first OBD readout is 100% OK.
greetings,
filecloud

[mauronow]

Your first OBD readout is 100% OK.
greetings,
filecloud

I have but the bad read. only has 1mb. and when I charge it tells me error galletto checsum.
i need original full file .

[filecloud]

I have but the bad read. only has 1mb. and when I charge it tells me error galletto checsum.
i need original full file .

Your flash read is OK!!!!
You need to fix your ST10 processor content and your eeprom...

[mauronow]

Your flash read is OK!!!!
You need to fix your ST10 processor content and your eeprom...

hello I can explain how I do it? please.
I fix the st10f275?
thanks friend!

[filecloud]

hello I can explain how I do it? please.
thanks friend!

You can use Byteshooter ST10 toolbox and ersa/beeprog for the eeprom.

[mauronow]

You can use Byteshooter ST10 toolbox and ersa/beeprog for the eeprom.

I have a g-4x to read. where byteshooter him? is a software?

[rsivan]

Post eeprom I will fix it
st10 no need to be tuned only flash most be

[mauronow]

Post eeprom I will fix it
st10 no need to be tuned only flash most be
thanks
to improve performance need only modify the 29f800bb? or do I have to do a full reading with galletto in bootmode of micro + flash?

[mauronow]

Hello
This is ME7.1.1 ST10 ecu!! Will not write over OBD with clone tools. US models have checksum in processor active, so flash + processor must be tuned.
With attempt to OBD write you killed eeprom and maybe processor content.
greetings,
filecloud
my connection diagram of my picture right? also connects to full bootmode reading?? is right ??

[filecloud]

my connection diagram of my picture right? also connects to full bootmode reading?? is right ??

No! You posted only ME7.1.1 plug pins. Contact your Galletto support for ME7.1.1 ST10 boot wiring diagram and verify that it supports this ecu. Read flash, read processor and read eeprom. You have to solder eeprom for this and read with beeprog.
Post all here.

[Overtune]

Here is connection.
Bild:VAG ME 711CAN 40Mhz Platine1.jpg - OBD-Wiki (http://wiki.obdtuning.com/?title=Bild:VAG_ME_711CAN_40Mhz_Platine1.jpg)

Test with FGTECH bootmode ST10F275. You could also use mpps at bootmode. But i am not if any of these 2 tools give you access to the eeprom.
Not tested myself.