Lexia 3 XS evolution reflash procedure

[guilhermegti]

Can someone help me with the reflash procedure for PSA XS evolution and the files needed.
I need to use Diagbox above 5.29, my old laptop (windows XP) is burned and the new is windows 7.
I have UPA usb.
thanks.

"sorry about bad english"

[mcgustoo]

Yes o can help first install Diagbox on your pc!

[guilhermegti]

Hi!
thanks for reply.
I already installed diagbox 7.2 on my windows 8 64 bits laptop. The Lexia interface was proprely installed, recognised adn updated to 4.3.0 by diagbox, but i can't connect to any vehicle because my serial number is blacklisted.
I dont know to update and dont have the files for winbound eeprom and fujitsu MCU.
Can you help me with that?

[guilhermegti]

Here are the drivers for lexia 3 VCI all windows 32 and 64 bits included windows 8, tested by me.

189295

[mcgustoo]

Do you have something to read winbond flash?

[guilhermegti]

I have UPA usb. What device should i choose to read winbound?

[Zmann]

There are two things to do to complete the reflashing procedures, Windbond and Fujitsu MCU.

For Windbound you can go with UPA, select EEPROM SPI M25P80 (or M25P40 depends on what is used) and set jumper to 3.3v. Read/write off circuit only and connect as SPI.

For the last needs another tool and the valid data (dump)!

[mcgustoo]

Okay then read this and save to your pc.... In my post about interface fix is dump for winbond. Write this to your flash with upa-usb. Thats all. When you do it let me know how works:)

[Zmann]

And the info seeming lost/hard to find from internet I think. Even it's the driver property but it's an effect from Fujitsu Flash.

http://i262.photobucket.com/albums/ii116/charl_ze/NewandOldFirmware_zpsd9968513.jpg

[smirnoff_rules]

can someone post a step by step and programs with firmware in and external download links . might and will help others

my clones seems to work fine on 7.6 but others are not

[arvedo]

rules very good idea, I have 2 clones and do not work I can give you the solution, please help with step by step to be able to operate thanks DiagBox clone

[guilhermegti]

I found this in a russian website.


189675



189676

189677


189678

189679

[guilhermegti]

189685

189686


This is the procedure to reflash fujitsu MCU and the software, no dumps needed just read edit and reflash
189687

[blacklisted]

any good enough to make pcb from schematics to flash fujitsu

[mcgustoo]

189685

189686


This is the procedure to reflash fujitsu MCU and the software, no dumps needed just read edit and reflash
189687

THATS RIGHT!!!!

[djscotch]

Someone knows any link to buy the programmer compatible with flash kit fujitsu software, i?m not good soldering :)

BR

[blacklisted]

yes i also look for programmer but cannot find cheap

if some one design pcb this will be easy

[arvedo]

hello good afternoon friend can help me how I can connect this thanks

[arvedo]

hello friend could read flash and 25x80 but files are not good can someone help me thanks

[Zmann]

25x80 dump is bad, good dump you can download from a famus thread there in the forum.

your flash dump was started welll and correct but the size is wrong and much smaller than it should be.

[carmelasse]

http://img856.imageshack.us/img856/2609/gl0.png (http://imageshack.us/photo/my-images/856/gl0.png/)What is resistors on this schematic (FlashKit29.rar)? Resistors on pins 11, 14, 15, 16, 17, 18 (74HC245) and pin 10 (MAX232) are 10K ohms; or only 10 ohms????

[carmelasse]

Any help? Nobody build this programmer?

[Zmann]

Never built it but all the resistors must be 10 ohms, 10Kohms are too much to those signals attenuation.

[kuti]

Already did it don't need this 10 om resistors. Works with flashkitprogrammer 2.9 async mode.
There is also need to connect +VCC to 20pin of 74ac245

[carmelasse]

Success!! Programmer build, all sectors of Fujitsu flash dumped, serial number of interface Actia/Lexia changed!! Interface work with Diagbox 7.07!!!!!!!!! (tested on C4 Picasso)

[Henk50]

Ik build this simple SPIPGM programmer for programming the winbond: RayeR's homepage/Programming (http://rayer.g6.cz/programm/programe.htm) It works fine, but you need an old PC with parallel port. The value of the resistors could be critical. I messure the signals, all where about 3.3V, but one, the ACK(MISO) where 4.2V. I put a resistor of 8k2 from pin 2 (DO) to ground, which reduce the voltage to 3.3V.

[racin-snake]

Invalid Request (http://www.digikey.co.uk/product-detail/en/A-SERIAL%20PROGRAMMING%20ADP/865-1113-ND/2499005)

this will do

[Marek_Spy]

Hello
my question is whether or LPT programmer to work? I found a very simple scheme LPT programmer .
RayeR's homepage/Program?tor SPI FlashROM na paraleln? port (http://rayer.g6.cz/elektro/spipgm.htm)

[Marek_Spy]

I program Winbond but nothing change ,

[Zmann]

How did you program it and what the programmer?

[Marek_Spy]

Program Fujitsu flash kit 2,9 and programmer schema and PCB 1:2 scale .

[Zmann]

You asked about Windbond but do not to answer what I asked back so probably you don't know that the programmer you're talking about does not do windbond. It must be done separately by only some programmer and off circuit only with 3.3v supplied.

[Marek_Spy]

No, I programing winbord UPA (3,3 V) programmer but serial number not change and not work with firmware 4.3.0 .
OK programmer work good , but I have not files to change serial number. Now I have good Fujitsu bin

[abdelamjid]

thanks to all

i have an lexia3 with serial ac 965250 the green led on but USB not recognized

plz help me

best regards

[111lisu]

Im find dump SPI

[hicuxh4ker]

will this one run on windows 7 64 bits?

[brchip]

hello good afternoon friend can help me how I can connect this thanks

So, is it possible to do with a JTAG board?

I happen to have one.

[abdelhak]

Program Fujitsu flash kit 2,9 and programmer schema and PCB 1:2 scale .

thanks man