peugeot 207 electric steering

[djcooper]

hello


I have a problem on a peugeot 207 in electric power steering.
When I connect the cable obd says it has internal error.
Someone can help me? Anyone have a virgin dump?

eprom : 95160
ref: 6700002168
q003ta0772ze 9z14
jtekt corporation

[diag1001]

hi this is the problem your derection does not work or what?
this is not working you not break your head this is a problem of transistor was bursting in moteure jai deja vue plusur times on the same car

[djcooper]

The steering do not work. Where is the trans?stor? Do you repair it?

[diag1001]

hi here is the photo transistor you find one or two bursting

[djcooper]

I find no such transistor
the electric power steering is in this photo

[Meat-Head]

how cool is that
l
ooking at the photos bet it was a pig to get to bits.

looking at that then gues the blown fet is on the back side of that 'spiky' heatsink.

[sdipi]

Hello
I'm in the same situation. I don't understand what are the transistor burned.
Are on this card? in the attached picture.

387689387690
Thank you.

[juan andres]

Hello
I'm in the same situation. I don't understand what are the transistor burned.
Are on this card? in the attached picture.

387689387690
Thank you.Hi, need solution? Thanks

Enviado desde mi XT1580 mediante Tapatalk

[Rui Ferreira]

resold the processors and gets the problem solved

[juan andres]

resold the processors and gets the problem solvedit does not work, any suggestions

Enviado desde mi XT1580 mediante Tapatalk

[juan andres]

resold the processors and gets the problem solvedSoldedhttps://uploads.tapatalk-cdn.com/20171122/afcf01cb2f342e60f7bbf9f08770df9b.jpg

Enviado desde mi XT1580 mediante Tapatalk

[starkindustries]

Hello, I am trying to solve this problem, I have the C1414 fault code. Changing the micropocessor worked? or do we have to change the transistors?Greetings.
Hello, I am trying to solve this problem, I have the C1414 fault code. Changing the micropocessor worked? or do we have to change the transistors?Greetings.

[starkindustries]

Hello, I am trying to solve this problem, I have the C1414 fault code. Changing the micropocessor worked? or do we have to change the transistors?
Greetings.

[Sauro1978]

C1414 is a problem of driver brushless motor.
you have to reball driver that are vs pink square in the dissipator side

[starkindustries]

Please, could you indicate where exactly the driver is that I have to change for error c1414,
Thank you,

[starkindustries]

Does anyone have any solution for error c1414?
I already change the micro for a new one and the error continues.
Please someone who has the solution, I have 2 modules to repair.

[electronikars]

Does anyone have any solution for error c1414?
I already change the micro for a new one and the error continues.
Please someone who has the solution, I have 2 modules to repair.

Hello you can contact me @my nick +.es, we can repair those modules for you.

Regards!

[starkindustries]

I also work in electronics. Could you help me to repair it please? I do not realize that part of the plate was burned. Check all the components and do not find anything. If you could give me a help I would appreciate it.

[Meat-Head]

Hello you can contact me @my nick +.es, we can repair those modules for you.

Regards!

Welcome to dk, the worlds best SHARING website
please spill the beans, on this subject, there will be other threads that make your eyes light up

fair exchange is no robbery

[Victor Lisnik]

Ola! Amigo! Eu tenho mesma problema com Peugeot 207 direção eléctrica não funciona. Queria saber se vose já resolveu problema da placa electrónica?

[manakov]

También tengo un problema. C1414 reemplazó los transistores de potencia 160N04, reemplazó 2 chips de controlador TLE7188F, el problema persiste, ¿qué cambiar para resolver este problema?

[juan andres]

También tengo un problema. C1414 reemplazó los transistores de potencia 160N04, reemplazó 2 chips de controlador TLE7188F, el problema persiste, ¿qué cambiar para resolver este problema?Hola, lograste solución? Estoy con el mismo problema

Enviado desde mi moto g(8) power mediante Tapatalk

[fra69]

hi for error code p0606 someone have solution?

[rafal]

hi for error code p0606 someone have solution?

check wirings from PAS to BSI.............
also poor battery can make this dtc

[Meat-Head]

Use different scan tool as well

[fra69]

check wirings from PAS to BSI.............
also poor battery can make this dtc
i see thet many rapair center can repair this fault on eps motor.
i check if there are somting wrong but i can't found it

[fra69]

i clearind board from protective film end reweld all connection ecu work.
p0606 clered and don't coming back

[momotcho]

i clearind board from protective film end reweld all connection ecu work.
p0606 clered and don't coming back

Hello fra69,
Did you disassemble all boards into the module (communication / interconnection / power) or only the top board (communication) ?
I have also a failing power steering on my 207 with P0606 fault.
I would like to find the root cause and give the info to the community
It seems that this module has a hidden defect that has never been corrected by the manufacturer. I suspect that issue is coming from power board (under the interconnection board) because we can observe a burned area around the big inductor at the entrance of the +12V. I'll post picture later ...

[fra69]

Hello fra69,
Did you disassemble all boards into the module (communication / interconnection / power) or only the top board (communication) ?
I have also a failing power steering on my 207 with P0606 fault.
I would like to find the root cause and give the info to the community
It seems that this module has a hidden defect that has never been corrected by the manufacturer. I suspect that issue is coming from power board (under the interconnection board) because we can observe a burned area around the big inductor at the entrance of the +12V. I'll post picture later ...

hi only remove comunication board on photo.
i rework all solder connection mcu included.
"burned area" it's normal because it's near a connection thet are soldering by high voltage

[momotcho]

Thank you for your reply.
I'll rework the communication board as you preconize.
I disassembled the other boards (translation board and power board). It's very difficult to disassemble them because they are soldered by spot welding.
Nothing seems wrong at this stage...
838564

[momotcho]

Hi all,
Come back with good news.
I reworked the communication board by resoldering all components to be sure that I didn't miss something.
Reassembled all boards in the electric steering, and put it in the car.
I cleared the P0606 error code.
My electric steering is working like a charm since more than 1 month !

Like third party companies are able to repair the electric steering within 24 to 48h, I'm now pretty sure that they don't dissamble all boards. I suspect that every time, it's due to an electric problem on communication board that is pretty easy to remove... (board on top).
From my point of view, the problem is coming from a bad soldering process on the TLE7188F (3 phases bridge driver). I observed that solderings on pins were not correctly flowed with pin and crack was probably formed with time (heat, vibrations, ...).
After reworking, these solders were well hooked to pins.
I put pictures for comparison and also the potential root cause.
Good luck if you decide to rework this electric steering :very_drunk:
853075
853076
Thanks again to Fra69 for his inputs.
And no thank you to Peugeot that has never seriously considered this problem and waited for customers to have a problem before changing one by one the EPS!

[mante]

Hello!
unsolder and resolder TLE7188F cured dtc C1414, everything works like charm. Anyway ori solder looks like a sh1t :)
Thank you :)

[robertocarlos75]

Good work.I have the same problem.Resoldering is the solution.First clean the gel with nitro.

[mclennan118]

I can confirm as well that reflowing the top circuit board cured our C1414 as well.
Thank you to all for help on this topic.

[pgt09dz]

help me
I have problem in my 207 Peugeot exactly c1414

[PremierD]

follow the top post ................

[pgt09dz]

follow the top post ................Brother could you help me for this problem c1414 . And I find this also .
So send me how to repair. Thank you https://uploads.tapatalk-cdn.com/20230514/172e42ae2f687ec570df6ed1305b638d.jpghttps://uploads.tapatalk-cdn.com/20230514/73cc48119d4fcab3bdece2354f62e450.jpghttps://uploads.tapatalk-cdn.com/20230514/50ddf314b8e0fd0b7862e7fbb55c6f4b.jpg

Envoyé de mon SM-G532F en utilisant Tapatalk

[Jview]

Hi all,
Come back with good news.
I reworked the communication board by resoldering all components to be sure that I didn't miss something.
Reassembled all boards in the electric steering, and put it in the car.
I cleared the P0606 error code.
My electric steering is working like a charm since more than 1 month !

Like third party companies are able to repair the electric steering within 24 to 48h, I'm now pretty sure that they don't dissamble all boards. I suspect that every time, it's due to an electric problem on communication board that is pretty easy to remove... (board on top).
From my point of view, the problem is coming from a bad soldering process on the TLE7188F (3 phases bridge driver). I observed that solderings on pins were not correctly flowed with pin and crack was probably formed with time (heat, vibrations, ...).
After reworking, these solders were well hooked to pins.
I put pictures for comparison and also the potential root cause.
Good luck if you decide to rework this electric steering :very_drunk:
853075
853076
Thanks again to Fra69 for his inputs.
And no thank you to Peugeot that has never seriously considered this problem and waited for customers to have a problem before changing one by one the EPS!

Thank you for sharing

[Valentin01]

What a great solution is this. Saves a lot of money! And is absolutely not difficult :redface-new:

[PACEVE]

I confirm, just re-solder the TLE7188F (3-Phase Bridge Driver IC). Its legs de-weld due to the high heating of the Choke inductor next to it.

Eu confirmo, basta soldar novamente o TLE7188F (3-Phase Bridge Driver IC). Suas pernas são des-soldadas devido ao alto aquecimento do indutor Choke próximo a ele.

Block Diagram of Driver Stages including Short Circuit Detection

Thank you for the informations

[batru]

1072751Peugeot 207 get code U1313 ( DAE no communication with ABS or ESP ), dashboard cluster steering wheel warning light on. I have different steering motor board (mitsubishi JQ331B15004A).Somebody have this problem with this type steering motor and how to fix it?

[firebladerr]

hi some problem here...did you fix it?




Brother could you help me for this problem c1414 . And I find this also .
So send me how to repair. Thank you https://uploads.tapatalk-cdn.com/20230514/172e42ae2f687ec570df6ed1305b638d.jpghttps://uploads.tapatalk-cdn.com/20230514/73cc48119d4fcab3bdece2354f62e450.jpghttps://uploads.tapatalk-cdn.com/20230514/50ddf314b8e0fd0b7862e7fbb55c6f4b.jpg

Envoyé de mon SM-G532F en utilisant Tapatalk