opel corsa c z14xe engine how to reset and program other ecu

[alhengary]

my car opel corsa engine control module didnt get signal to ignition coil no 1 and injector no 2 i get just ecu from other car same system same part number but how can i reprogram it
thank you

[nicocr]

you must virginize new ecu, and program it with op-com or similar. you must need original pin code and pin code of new ecu (or load virgin dump to new ecu)

[nikostzimis]

with carprog :CODECARD.LT - advanced tools for car electronic repair. (http://www.codecard.lt/)

[alhengary]

you must virginize new ecu, and program it with op-com or similar. you must need original pin code and pin code of new ecu (or load virgin dump to new ecu)
i got used ecu and car pin code and i dont have used ecu pin code and this tipe of ecu doesn't unlock

[philipcoin]

op-com and carprog,
can do this job.
you have to get the pincode of both ecu,you can read pincode with carprog,
and virgin the new one with op-com and program ecu.

[alhengary]

op-com and carprog,
can do this job.
you have to get the pincode of both ecu,you can read pincode with carprog,
and virgin the new one with op-com and program ecu.
please more explane

[philipcoin]

please more explane


do you have op-com and carprog
or which tool are you using to program the ecu.

[alhengary]

do you have op-com and carprog
or which tool are you using to program the ecu.

just original op-com

[credoline]

If you succed to read pin code from used ecu with Carprog, i will explain you what to do.
Without Carprog or pin code from donor ecu, you can not do the job.
If you have in Tripoli Opel service pay to them pin code from VIN, and VIN of donor ecu you can see with OPCOM.

[philipcoin]

just original op-com


you have to get pincode for both ecu.
before you can reset the new ecu.

[philipcoin]

please more explane


these are the steps-
you have to reset the new ecu with its pincode,
you click on program
next-reset ecu you enter the 4digit pincode of the new ecu
after that u click on the reset ecu again
you enter the 4digit pincode for the old ecu.
you go to the immobilizer
click on program
enter 4digit pincode
choose immobilizer output funtion
you are only replacing ecu
so you choose changing of engine control unit.
you are done.

PC.

[credoline]

Its not possible to reset new ecu on car the way you have described !
That is possible on that way when that (new) ecu is in their own car, in another car its not possible that way !
It is also possible, but not on that way!

[philipcoin]

Its not possible to reset new ecu on car the way you have described !
That is possible on that way when that (new) ecu is in their own car, in another car its not possible that way !
It is also possible, but not on that way!

yes mate,
it depends on the type of opel car.
not all opel can be program with this steps
newer opel cars you have reset some modules too.

PC.

[alhengary]

Its not possible to reset new ecu on car the way you have described !
That is possible on that way when that (new) ecu is in their own car, in another car its not possible that way !
It is also possible, but not on that way!
so what ?????

[autoden]

I,m sure you can read pin code with op com on corsa c. Body/ instruments/Special functions then eeprom.
autoden

[credoline]

Yes, and this way he can get pin code from car, but he also need pin code from donor ecu.
And after he get both of pins, if he not want to put new transponder, he also must have programmer to r/w immobilizer

[speedy100]

I need to swap ECU of Corsa C 1.2 with M1.5.5
I have the car's pin code but not the new (used) ECU's.
I have original Carprog but do not see M1.5.5 in its options.
Any ideas how I can read the pin code from this type of ECU?

Thank You for Your time.

Best Regards

[credoline]

In Carprog, ECU/ Opel K line/Bosch ME 1.5.5 ECU or Bosch M1.5.5

[speedy100]

In Carprog, ECU/ Opel K line/Bosch ME 1.5.5 ECU or Bosch M1.5.5

Thank You Credoline!
Unfortunately the Carprog manual for Opel ECUs does not include the pinout for M1.5.5 so i do not know how to connect.
Do You have the pinout for this ECU type?

Best Regards

[deondti]

That ECU should read from the K-Line ( via OBD plug)

[speedy100]

That ECU should read from the K-Line ( via OBD plug)

This is not the car's original ECU i want to read. It is a used ECU i want to virginize so i adapt it on a Corsa C.
Will it read it via OBD just by plugging it on the car and switch ignition on?

B.R.

[deondti]

This is not the car's original ECU i want to read. It is a used ECU i want to virginize so i adapt it on a Corsa C.
Will it read it via OBD just by plugging it on the car and switch ignition on?

B.R.

YES that is correct

[credoline]

"Will it read it via OBD just by plugging it on the car and switch ignition on?"
No, Opel do not work like that.
On Codecard website you have pictures for connection on table, just search for it, its little confused on their pages, but it have.
If you not found i can upload it for you (but i do not support lazy people)

[deondti]

Very interesting statement credoline . I have done many....

[speedy100]

Well guys,

It is truth Credoline that the OPEL manual of Carprog has most ECUs that the hardware supports but not the M1.5.5 so i did not know how to do it on the bench.
It is also truth Deonti that Carprog does read via OBD using adaptor A1 both the original and the new (used) ECUs just by pluging them in. I do not know about other ECUs but the M1.5.5 show no pincode for either one but only 0000 in the pin field. It does show tho the correct VIN of both cars original and donor.

By reseting (Virginising) the new (used) ECU via Carprog I then managed to adapt it to the car via OP_COM by programming it using the original car's pincode.
No other adapting - programming of keys etc. is necessary. The car started right up.

B.R.

[credoline]

Yes, adapting, not ignition on and start, like Fiat or Renault. M 1.5.5 is different type of ecu than others Opel ecus.
Link on codecard:
OPEL login reader from motor hybrid ECU. (http://codecard.lt/carprog/software/opel-login-reader-from-motor-hybrid-ecu-works-with-bosch-me1-5-5-siemens-simtec71-simtec71-1-delco-diesel-delco-multec-/prod_129.html)

[alhengary]

what adapter can i use for my ecu i got car prog and i dont know how to read ecu pin code pleas helphttp://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=292411&stc=1

[philipcoin]

what adapter can i use for my ecu i got car prog and i dont know how to read ecu pin code pleas helphttp://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=292411&stc=1
WORKS BY OBD2 USING CABLE A1,OR REMOVE ECU FROM CAR AND USE CABLE 15.



PC.

[alhengary]

WORKS BY OBD2 USING CABLE A1,OR REMOVE ECU FROM CAR AND USE CABLE 15.



PC.
i used a15 cable but cant read ecu more explane please
tank you

[philipcoin]

i used a15 cable but cant read ecu more explane please
tank you
use A15+CARPROG ADAPTOR

PC

[alhengary]

use A15+CARPROG ADAPTOR

PC
use k-line 0r can ??? my ecu is hsfi 2.1????

[philipcoin]

Use k-line

[philipcoin]

Choose ecu type
And read pincode.

[alhengary]

ecu cant read i connect green wire in pin 54 but ecu not response
regards

[philipcoin]

ecu cant read i connect green wire in pin 54 but ecu not response
regards
THE GREEN WIRE IS THE K-LINE IS NOT PIN 54 IS PIN 5
CHECK PIN CONNECTIONS WELL.

PC

[alhengary]

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=292435&stc=1
THE GREEN WIRE IS THE K-LINE IS NOT PIN 54 IS PIN 5
CHECK PIN CONNECTIONS WELL.

PC
thats what i did if am wrong plz tell me how
thank you

[alfons37]

I have same problem, anyone can tell how i read all dump with carprog?

[Shmortz]

put ECU on car and read via OBD

[alfons37]

OK thanks, so i can read/write full dump with carprog on OBD?


I have opel corsa HSFI-2.1 09353469

[alfons37]

Now i read with carprog via OBD, work very good, read all dump and save. Now i install new (used) ecu to car , and i write back all dump from bad ecu. And i read all dump again and right chassi number and pincode all ok. But when i try start car, car cranking but not start and immo light flashing. I read codes under ecu and it tell p1615 and p1616. And read codes under immo and it tell 0 codes. What is problem? Maybe new ecu is bad....

[iren71]

You need to reset the dashboard, immo and body with your car pass code. only after pulling the pin code of the new ECU, ECU reset with opel com, and only then reprogram all 4 items

[alfons37]

Where can i find car pass, or can i order this on opel with chassi nummer? And must i reprogram dash,immo,body,ecu with new software, i dont understand:)

And i work before on opel and it work , i read and write back and always work , but not on this car..

[iren71]

sometimes happens, try to pin, resetting tool bcm and immo, then connect your new ECU resets the same with the pin of the new ECU, when you reset the car reprograms all with the original pin . for pin code you can ask in dealeship or read from immo box

[alfons37]

I have read ecu with carprog and have pin code, is it same pincode as car pass?

[flyins]

I have read ecu with carprog and have pin code, is it same pincode as car pass?
Corsa c pull pin from dash for car then used ecu carprog for cars ecu, then reset ecu with ecus pin then go to immobiliser and immobiliser function put pin from car in engine ecu, or bring car to manchester and i do for you
also watch in measuring blocks for security wait time!!

[alfons37]

Now all work, problem was no key programmed...

[alhengary]

just program new key with op-com or by immo dump