Immo Audi A6 with VP44

[panderetamix]

Hi.

I try to coding VP44 with 1957 code and not work. I need immo off of this ECU.

Thanks.

396428

[baltazar3]

Hi.

I try to coding VP44 with 1957 code and not work. I need immo off of this ECU.

Thanks.

396428
VIN : WAUZZZ4B42N013222
KM : 538251
PIN : 1957
Immo status : OFF

[panderetamix]

The car dont Start, ithink need immo off in flash.

Thanks.

[baltazar3]

The car dont Start, ithink need immo off in flash.

Thanks.
Try this...same pass

[panderetamix]

Dont start :(

[baltazar3]

Dont start :(
post DTC from ECU and cluster

[panderetamix]

ECU 00542
Dash 1300, 1304.

[baltazar3]

ECU 00542
Dash 1300, 1304.
00542 - Needle lift Sensor (G80): Open or Short to Plus Possible Symptoms

Malfunction Indicator Light (MIL) ON
Pre-Glow Indicator Light ON

Possible Causes

Wiring and/or Connector(s) from/to Needle lift Sensor (G80) faulty
Needle lift Sensor (G80) faulty

Possible Solutions

Check Wiring and/or Connector(s) from/to Needle lift Sensor (G80)
Check/Replace Needle lift Sensor (G80)

[gokhanusta]

try friend pass pm

[panderetamix]

Dont Start, same error in ECU.

[panderetamix]

00542 - Needle lift Sensor (G80): Open or Short to Plus

Possible Symptoms



Malfunction Indicator Light (MIL) ON
Pre-Glow Indicator Light ON

Possible Causes



Wiring and/or Connector(s) from/to Needle lift Sensor (G80) faulty
Needle lift Sensor (G80) faulty

Possible Solutions



Check Wiring and/or Connector(s) from/to Needle lift Sensor (G80)
Check/Replace Needle lift Sensor (G80)



I've talked to a Bosch Car Service and tell me that this failure does not make the vehicle will not start.

[baltazar3]

You dont have any DTC in Engine ECU tied to IMMO ?
Take a look in measures block ( start enable YES=1,NO=0)
If YES,probably is VP44 pump faulty.Even is immobiliser active car must start for 1 second.

[panderetamix]

VP44 is new but i cant coding.
You know what channel is it?
I do not see any ask that.
The engine always rotates but does not start.
Thank you.

[baltazar3]

VP44 is new but i cant coding.
You know what channel is it?
I do not see any ask that.
The engine always rotates but does not start.
Thank you.

Injection Pump Swapping Prerequisites:



The NEW Injection Pump is installed in the car.
Battery voltage at least 12.5 V.
Make sure to have the Immobilizer PIN, for the Engine Control Unit (ECU).


[Select]
[01 - Engine]


[Login - 11]



4-digit PIN

The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.



[Do it!]


[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]



4-digit PIN

The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.



[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]





Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
Start the Engine to verify the adaptation was successful.

[panderetamix]

I channel 50 always says 32000 and never change.

[baltazar3]

I channel 50 always says 32000 and never change.
32000 is ok....You have to write ori files back and than try to code pump.

[panderetamix]

I write 01957, acept, read again an sais 32000.

[baltazar3]

I write 01957, acept, read again an sais 32000.
After accept code log off from ECU,ignition off for 1 min. and start car.

[imad9255]

hi
Please Help

I am a car technician who has come to us with a car of Audi type A6 1999 2.5 V6 AFB ECU 4B0 907 401 S EPROMM 24C04
There is a problem with the main turbocharger. The turmeric has been replaced by the same engine model but the new car model 2001
Now I can not program Trumpet because I can not get it PIN CODE ECU
The first question is the 1999 Trumpet is the same as the Trumpet 2001. Can we program it?
The second question is whether 1999 programming is the same as the 2001 programming as is evident in this link in Russ Tech
http://wiki.ross-tech.com/wiki/index.php/Immobilizer_III_Injection_Pump_Swapping
I will attach the existing EPROMM file I can get PIN CODE Or is there another way for the 1999 model?
I have two ECU