08 pilot 95640 read not correct

[dualboot]

Hello everyone, this is my first time trying to read an eeprom. I have an 08 Honda pilot 77960-s9v-A512-C1 when I read using carprog 9.31 it reads all zero`s. After it reads it verifies ok anyone help me out with this. Thanks

[repairmymodule]

Check your connections. How are you reading, with chip removed from board, in an adapter or in circuit?

[dualboot]

Reading in circuit, damn chip is so small is hard to solder on to it. I soldered two wires in the back 4 on the chip.

Sent from my SM-G935V using Tapatalk

[repairmymodule]

Yeah I just did one it's a bitch. But you may have wires in wrong place. They should read fine in circuit

[dualboot]

How did you do it, any pictures?https://uploads.tapatalk-cdn.com/20170428/25fa500c51d97eb0171abb5885a70f42.jpg

Sent from my SM-G935V using Tapatalk

[janushaan]

ouch,, that looks no good,,

you can try this http://www.ebay.com/itm/TSSOP8-spring-loaded-pogo-adapter-for-Carprog-cable-EEPROM-programming/262712675737?_trksid=p2047675.c100011.m1850&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%2 6asc%3D40130%26meid%3De3dbc6eac1f0460fba3cb88be2f2 cecb%26pid%3D100011%26rk%3D2%26rkt%3D3%26sd%3D2618 07833813

or these clips - https://www.amazon.com/Cal-Test-Electronics-CT2848-12-Pieces/dp/B009QBH87M

[dualboot]

My soldering iron needs new tip. Those look great, if I decide to do this for money will definitely buy them.

Sent from my SM-G935V using Tapatalk

[dualboot]

Well I tried reading another chip for a Toyota rav4 and got the same reading. I removed the chip from the board and using the A6 connector I get the 00 readings. It looks like maybe my carprog is no good. I used external power and after numerous no chip detected I got a reading of 00. https://uploads.tapatalk-cdn.com/20170503/d832a421f25d503a29b6cdbedc23c8ba.jpghttps://uploads.tapatalk-cdn.com/20170503/5954cef747b190fa7bb17272eb9d288d.jpghttps://uploads.tapatalk-cdn.com/20170503/bcdd742df6cf1633594272a713e5dd4f.jpg

Sent from my SM-G935V using Tapatalk

[repairmymodule]

Make sure pin 1 one your cable is on pin 1 of the chip.

Also make sure your cable is wired correctly. You can find diagrams for the cable on codecard website. I have found some clone cables are wired wrong

http://www.codecard.lt/carprog/adapters/a4-carprog-eeprom-programming-adapter/prod_54.html

[dualboot]

Thanks for the response, I did verify the connector is wired properly and clipped the chip the right way.

Sent from my SM-G935V using Tapatalk

[borshch]

Clone or original carprog ? Don't forget to attach the eeprom connector board between carprog unit and a4/a6 connector

Sent from my Moto G (4) using Tapatalk

[dualboot]

Clone, I have tried with and without external power and with adapter.https://uploads.tapatalk-cdn.com/20170504/3440561ae039d5436f9bc3805a651b14.jpg

Sent from my SM-G935V using Tapatalk

[borshch]

does it read 0000 for all eeproms or just that one ? If for all, than you probably need carprog repair kit

Sent from my Moto G (4) using Tapatalk

[dualboot]

I have tried on two and get 00. Can you point me to the repair kit? Thanks again

Sent from my SM-G935V using Tapatalk

[borshch]

I have tried on two and get 00. Can you point me to the repair kit? Thanks again

Sent from my SM-G935V using Tapatalk
http://www.codecard.lt/carprog/carprog-repair-kit-4x-74hc125-4x-22uf-capasitors-1x-mcp2515/prod_566.html

Sent from my Moto G (4) using Tapatalk

[borshch]

Look at this on eBay http://www.ebay.com/itm/262933091953



Sent from my Moto G (4) using Tapatalk

[dualboot]

Thanks guys, for all your help. I will post a follow-up after doing the repairs.

Sent from my SM-G935V using Tapatalk

[dualboot]

Hi everyone, I finally did some repairs to my clone and I was able to read and verify a 93c66 for a 09 Rav 4. Denso 89170-0R020, can someone check this file for me and clear if possible so I can finally feel some success. Thanks all

[zckariya70]

Try this.................

[dualboot]

The file you sent me wrote and verified perfectly, Thank you.