Renault Clio UCH repair and replacement width new versions

[mexanico1971]

I People
I dont know if exist any thread about UCH repair and replacement
Old versions like Sagem BG or N?1 are not available any more
S? any one knows any source to buy it ?
wicth version is use now for replace old ones


About repair , i see that major problems are solders in PCB parts , not in connectors

http://i65.tinypic.com/244pnd3.jpg



http://i66.tinypic.com/15yaioj.jpg
Newbies , wend you want any pass , send PM to the guy , don"t span the thread

[albertros]

Hi,
BG can be replaced with N2, HG replaced with N3.
N3 will replace N2.
N1 seems to only like N1
Not complete list but a start.

[mexanico1971]

Thank"s for your input
So if BG can be replace width N?2 why does N?2 have delay after turn key off ?
I mean I switch off the key, and take it out of the ignition, and engine only 4 seconds later shot off ?
Any idea ?
I coded UCH width Clip

Thank"s in advance
Brs

[guerraa]

Hi, after UCH replace do a ECM reprograming and all will be ok, dont know why but worked all times for me.

Best regards

[Dunker]

Solder all caps etc. under black 40 pin connector. Solves 99% of UCH faults.

Also, for your own reference, from a good UCH measure all components to PCB GND under the connector and write all values down. Will give you an idea if a component or something connected to it is not right. Will save you hassle of removing connector more than once.

[Louislesinge]

Hi,
What I can tell you is I've change about 50 UCHs in my life, most of them with original parts, and a lot with used parts.
You can allaways change Nx for a same grade or higher (N1 instead of BG, N2 instead of N1 etc).
Another speciall thing is if you got a Clio with engine 1,9 DTI, it needs to be the same UCH because of the antitheft. No other UCHs works for antitheft instead of the original: it happens to me twice ( red light stays on without flashing, it means no comunication UCH=>ECU) and I did not find another solution than removing antitheft from ECU 0 281 010 788 .
I've tested virgin, copying, all desperate things you can do.
I think this kind of ECUs have a special protocol.
Regards,

[Louislesinge]

Hi,
By the way I order an UCH to replace BG P8200065817 G1 V4.1 , the replacement from Renault was 82 00 621 763 written N3 instead of BG.
Regards,

[Louislesinge]

Hi,
For the same UCH BG P8200065817 G1 V4.1 pulled up from recycle.
Antitheft light blinking permantly, does not reconise or even see any key i tryed (tested reset and another antena etc).
Tested continuity beetwen pin8 Black connector 40 ways and SAGEM E34707A OK (near the same connector upper right side, no contact to earth.
Tryed to replace the chip SAGEM E34707A from another working UCH: Now works fine, can learn the keys again, car starts.

If some needs electric diagram:
504253
Regards,

[tomo776]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

[Louislesinge]

Hi tomo,
I'm interested in your investigations, please send PW.
Regards,

[Louislesinge]

Hi,
Ok tomo, i'll try to follow the electronic circuit to understand.
You don't say which problem this change solves: antitheft light staying on or flashing, etc. Those are for me the biggest problems because many times they are sporadic. The last one i save changing SAGEM E34707A, was permanently inoperative, a kind of breakdown easy to fix.
Regards,

[tomo776]

Problems is
Car does not start,electric window problem, lights dont work etc.
Car going crazy and sometimes when you pull wiring of uch car work ok but this fix this errors.
First is sporadic that car does not start and problem with electric in car but then fail to start after some time.

This fix if car start doing this with no reason.
If someone change batery and reverse polarity mix + and - this is not fix for this.
And if some part inside uch is burn for some reason.

[nagyfeco82]

hi
Why i cant download tomo776 post attached links

[ecuelettronica]

non apre il rar file dannegiato

[cemar]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Password please, tank

[karsan]

Password please, tank

[medonline]

Thank"s for your input

[hrmotorsport]

Please pass. Thanks

[MAKS79]

Pass please. Thanks

[alclot]

Hi mate,
Can I have password please?
Thanks in advance ;)

[tomo776]

Please ask pass on pm.

Best regards

[Meat-Head]

Please ask pass on pm.

Best regards

why password stuff?

do you put a padlock on your cat carrier when you take it to the vet?

[bmpedrosa]

Pass please.

[Manuelgb]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards


Friend, can you pass?
, I have one uch has me crazy. Thank you

[mexanico1971]

Ask the guy password by PM , don"t make this pass please thread

[Meat-Head]

Ask the guy password by PM , don"t make this pass please thread

If there was no password, would not infuriate people

PASSSSSSSSSD THANNNKKKSSS

[mexanico1971]

If there was no password, would not infuriate people

PASSSSSSSSSD THANNNKKKSSS


Lot"s of the people who are asking for pass are lechers , I have discus this same years ago !
Its up to each other to decide protect the researching we made , I se very times in Ebay and in other inferior forums solutions that the Old people "Vet and Vip"s " on DK found by sharing know bettwin them .
And people that came here for download must have respect for does o open the way to knowledge.

Best regards and Nice weekend

[Meat-Head]

Yeah, but no matter who asks who and gets pass it's going to end on ebay
which is sort of 'good' as at least you can get the information without having to wait weeks

[chipcarcordoba2]

please... pass, i need view... thanks

[Codekuba]

Please pass :)
Thanks

[puco344]

HI there,

Can somebody help me to solve my UCH clio2 problem? I would pay it via paypal, just PM me. (if you can send me a good UCH for the old one)

My wife has a 2001 16v 75LE 1.2 clio2 and the UCH sometimes stoppes the index blinker. Very dangerous(!), my kids are inside the car.
And sometimes the windscreen wipers stops + I hear many relay clicking sounds from the uch box I guess, like an old tram from nineteens.

My UCH is : G1 V4.1 21 658 964 -5b 26/06/01

Reading your prev posts, I see I can change it with an N1, or N3? (the car has no clima and only the first windows are electricals)

Thanks,

[tomo776]

Did you try my solution?
If you have soldering skils you can do it.
For change uch you must have virgin dump for uch and ecu and renault clip. Or put new used uch and make new keys and make configiration of uch to match you equipment that you have in car.

Regards

[puco344]

Hi, can you send me password to unpack your solution? (i don't know what is it)
What I did today is I resoldered the 40 pin black connector, but got no luck.
When UCH stoppes the wiper, switching on the blinker starts the rear wiper too, all the time despite it is off.

I have OBD immo key overide tool from hickleys.com and I bought some cheep remote controller to control the door lock => I guess my UCH has been in bad condition for years

Can I just replace G1 V4.1 21 658 964 -5b 26/06/01 with a cheap used N2 v4.3 ? My friend is an electrican at Renault saloon in my town, he has tools to reset, copy UCH, and said the new UCH is around 400 british fonts, our car not worth so much.

[carocar]

hi
anybody has pin out for this module ? i resolder everything on the board.
in my case i can reed with immo tool eeprom data over obd but i can´t read the hole car only airbag answer???
car is not starting light window wiper and remote work good. starter only work for 2 sec

[robertpaul]

[QUOTE = tomo776; 3220718] Problemas e o
caminhão Não Iniciar, Problema de Janela Elétrica, Luzes Não funcionam etc.
Carro enlouquecendo e as vezes when rápido Você puxa um Fiação do Trabalho do Carro uch ok, mas ISSO Corrigir ESSES Erros.
O primeiro é esporádico que o carro não inicia e o problema com o carro elétrico, mas depois não se conecta com o impulso de algum tempo.

Esta correção se o carro começa a fazer isso sem motivo.
O trocater de bateria e inverter a polaridade, misture - se.
E se alguma parte do seu interior estiver queimada por algum motivo. [/ QUOTE]

[carmona]

hi tomo please send the passw many thanks

[KISATEC]

Pass please

[PiciGSM]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Hi!Send me a pass pleas!
Thank's!

[einet]

this unit cost 150€ on renault

[Wiggy123]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Hi there. New to the forum. I see this is an old post but I am having the same issue. Has anyone been able to find the solution? Any feed back will be much appreciated. Thanx

[mexanico1971]

Guys !
Don"t ask for pass in the thread
Send PM , to who put the files

Thank"s

[McDowell]

------------------------------

[nemanja12345]

Please pass :)
Thanks

[zefoguete]

pass please. thanks..

[kompleks2]

Hello. Please pass. Thank you very very much.

[neksus]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Hi,
can you give me the pass?
Thanks in advance

[dardoelectro]

Hello, thank you very much for the information, I would like to try your file.
Please send pass.
regards

[TULGEYWOODMAN]

Hi,
BG can be replaced with N2, HG replaced with N3.
N3 will replace N2.
N1 seems to only like N1
Not complete list but a start.
What can replace N3?

[Meat-Head]

What can replace N3?

No idea, use stalk function for “Obdmaster” not sure if was posted online or offline
but he was playing with himself and discovered odd things like no headlights or nor windows

if you cant find excact unit you need, get chepest off ebay and/or
”price up new from dealer” ask for latest part numbers

[garciaefren]

https://renaultmegane19.blogspot.com/2015/11/unidad-control-habitaculo-uch.html

[reprog12]

pass please thank you

[AsteveA]

Hi Tomo,

I am interested in your investigation please could you send PW

Regards

Steve

[zzivo]

Hi,
can you give me the pass?
Thanks in advance

[gentil]

Hi, you can send the password? Thanks

[clinic]

pass please
passe por favor

[volorucinski]

What can replace N3?

Did you tried the opposite? HG and N2?


.
FREE SOLUTION IN POST #50. READ BEFORE ASKING PASS, YOU LAZY PEOPLE! ASK PASSWORDS ONLY IN PM! STOP THIS "PASS PLEASE" SPAM.

[fast7850]

pass please than you

[vinz]

Hi,
can you give me the pass?
Thanks in advance

[bokki]

Please send the passw many thanks

[joaoteixeira]

pass please , thank you

[electro10]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Password please

[race1181]

Password please, tank

[Dede1989]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Hi ! Thanks for your work ! It's possible to have the password ?

Sorry for my bad english i'm from France ;)

Have a nice day

[koranx]

password please

[mince69meat]

Hi.
I found something and repair this uch without them come back to me.
It take me a lot of nerves to find this but I wanna to find what can be done and after that solution I repair more then 10 uch and cars work more then 3 years without problems.
If someone need this ask on pm for password.
I use picture from 1 post of mexanico1971 .
And my picture high res. to see how it`s look after repair.
Soldering is not my best work but in late nihgt hour when I work this can pass.http://www.digital-kaos.co.uk/forums/images/icons/icon7.png

Regards

Password please, interesting

[lidons]

Hi guys, is this solution also repairable for Renault traffic, Nissan Primastar and Opel Vivaro UCHs? I have two with the same problem, fixed light does not blink, the keys recognize it, but it does not have start authorization..

[krug]

Bitte um PM.

[autel15]

thank you should be very nice i you tell me the pass and see the great work

[mexanico1971]

Newbies , wend you want any pass , send PM to the guy , don"t span the thread