NO CA FOUND/FILE TO BIG FIX

[halau]

If you have bought an 800 recently and come against some problems with flashing then this might be the fix for you

I was told my box was 75 bootloader but ok for 72 aswell i tried to flash and got the ' NO CA FOUND '

Some times it would boot up with dreamup in 'serial http mode' but could never find a working IP and failed when trying to flash,

The rest of time it would boot up in dreamup with the 'NO CA FOUND SeCOND STAGE BOOTLOADER' this would allow me to use enforcer but came up against the 'FILE TOO BIG' problem

If you have problems like these try my method below it worked for me

[halau]

Ok with help from Superman at supersatshop this is what i done and it worked

connect dreambox to router
use crossover cable connect router to laptop
open dreamup
connect null modem
connect power to dreambox while holding silver power button till dreamup has fully loaded
find IP of box (i used dcc) mine edded up being a very strang 192.168.1.6
put this in dreamup
open enforcer
load image and flash


I have found the Gemini images are useless as i done all above and it failed to boot up again so best to use another i have nabilosat and all is fine here

Again thanks Superman for your hours of help

[southpaw]

pretty simple fix , mine took best part of an hour using null cable and crossover together , good luck

[bstrandm]

I tried the solution here but still cant get contact

[stef73]

ok guys lets be certain youre using the right image, i.e if its a new dreambox itll be sim 2.01 and you need that gemini inage or what other image you need but it must be for the sim 2.01 i tried without success for a week too and then i realised what i was doing wrong gemini nabilosat and excalibur images now work fine and scan all channels including the hd ones

[sapcons]

Folks, I am lost and about to give up.

After some problems I decided to install a new image. The result was the 'CA no card found' error.

The box doesn't 'stop' and doesn't show a IP.
DreamUp seems to connect, but any SSL file results in a 'file too big' error.

PLEASE HELP.

[toroloco74]

OK...I know this is a very trivial questions but can someone tell me what a null cable is and do I need it if I can connect wireless via my router to my DB? I'm having the same problem but can't figure out how to connect in order to upload a new image. My web interface is not working for some reason. I feel like a moron asking these questions because I am a techie by trade but teh DB has ma at a loss.

[iburger]

I have a dm800 that I am supposed to do development on. I did not know it was a clone. I didn't even know clones existed (it isn't mine, I just have to develop on it). I built a new dreambox image from source last night and flashed it. Now I have the CA not found error. So far I cannot get it to do anything. To make matters worse, I do not have a windows PC either, as I am a linux/python developer by trade.

Seriously beginning to wonder if it cannot be reprogrammed with a flash programmer or something...

Anyway. That is my story, and the first obligatory post before you can see anything. Seems I will be around for a while while building this thing.

[iburger]

Alright, in case someone else passes this way and needs a solution.

The box that you run DreamUP on MUST have a working network connection. Even if you don't use it. This is, strictly speaking, a bug in DreamUP.

I unearthed an old Pentium I in my garage, installed Windows 98 on it, built a null-modem cable from an old modem cable, and immediately got the error: '' is not a valid integer. Finally got tired of transferring files by floppy/cdrom, so I installed an old PCI network card, got the network going, and lo, DreamUP started working. A few tries later, and the dreambox clone successfully claimed the IP configured by DreamUP. Connected to that IP with a web browser, uploaded boot loader version 69, and voila, it boots again.

Now it complains that the hardware could not be verified, on screen. But I do not care too much, for I can telnet to it now, I have a root login, and I know about the linux kernel :-) And I made a copy of the software it came with, which I can write back to /dev/mtdblock/3 if I have to.

[idream]

Worked very well thanks, i found it start flashing 2nd phase nfi automatically after dm800 was rebooted :)

Its good to know there is always a work around to revive

i may try the 2.01 sim in my diablo wifi twinbee socket & see if i can read/write via cas3 programmer

[edensan]

gonna try for sure let you guys know...

it works like a charme!!

lttl ps i dont have the dreamup pc connected to the router..
so this is what i have done..

db on router
0 modem cable
rest like described...
superb!!

[loady]

Is there anyway to erase flash these boxes, i have been trying for weeks now to flash bonesys dump of his 14 day epg gemini image, i can only assume that there is something wrong with the dump because i can flash ANY other image to the box with ANY dm800 compatible version of dreamup....but not his one, i allways get 'invalid image, box will be unusable now' on the web interface or 'invalid image 010!!!' when using dreamup...im pulling my hair out over this but no one seems to be able to offer me an alternative dump of the image.

[umutgenc]

Hi,

I have just joined to forum and trying to see the attachment in first post. But site does not allow me. Can you please describe the step instead of sending screenshots? Thanks

It just appeared after posting one message :)

[hey69]

Is there anyway to erase flash these boxes, i have been trying for weeks now to flash bonesys dump of his 14 day epg gemini image, i can only assume that there is something wrong with the dump because i can flash ANY other image to the box with ANY dm800 compatible version of dreamup....but not his one, i allways get 'invalid image, box will be unusable now' on the web interface or 'invalid image 010!!!' when using dreamup...im pulling my hair out over this but no one seems to be able to offer me an alternative dump of the image.


you sure that image has no faults cause to me it looks like a bad firmware

[Windviper]

Hope to solve this tomorrow. I'm happy to see there are helpful people out there.
New on this!!!

Thanks.

Reeeaaalll Happy.
Everything works.

You find the solution in this:

http://www.digital-kaos.co.uk/forums/downloads/other/8/dreambox-enforcer-990/

I used a twisted serial and port 1 in dreamup

[dream_box]

I still have "file to big" after your procedures!
What can i do?

[John-2k10]

File to big, yay, yippee.. dm800 clone.

My disaster.

Crossed lan cable and working rs232 cable connected.

Using universal dreamup 1.3.3.4 with http and telnet
Status, Box is in networked http mode.
Error No CA found by 2nd stage loader etcetera

Log,
box type DM800
Enabled recovery of bad sectors
No CA found by 2nd stage loader....

Result, have an ip 10.0.0.2, gateway 10.0.0.112 from dreamup and can ping it, have telnet / tftpd and http web with flash uploading.
No ftp service active.

However, web flash 100% and still no go, dreambox display only says error.
Terminal say nand-set-pen, start flashing..., finished.
Also strange, with telnet his advanced setup util, settings are saved because i can see the action in the terminal but it's gone by a dbox restart.

[sat24]

Hi

Unfortunately i am not able to use serial connexion on my DM 800. I tried a lot of Dreamup version without any succes.
Who can give me the right oinout for null modem working with DM 800
Thanks a lot for your help

[John-2k10]

Use two female D9 connectors.
Best way is to keep the cable short,
something like +/- 50 cm/1.62 feet / 19.44 inches.

Connect,
pin 2 to 3
pin 3 to 2
pin 5 to 5

if you prefer a USB rs232 cable search Google, dreambox rs232 usb cable.

[John-2k10]

Other issue,
My experience is that the dreambox (clone) rs232 chip is very fragile.
There nearly no rx/tx security's to the smd chip Sipex SP3243E (R1-in pin 4 and T1-out pin 9), only two smd capacitors, the line of the DB9 rx/tx pins going striate to the chip.
Also the print lines to the chip are very thin.
So, my advice is, be sure to use an rs232 cable with the right connections and never pull it out/in when the box is in on state. .

[sat24]

Hi all

I would like to thank you all. After manufacturing a null modem cable i got my serial connexion working.
I used the enforcer tools and now my DM800 is up again.
Sorry for my english.
Best regards

[gucio13]

Dear team
after I tried to install new image I get also Error: "no ca found".
Then with null modem cable I can't update because: file to big.
Pls help.

Gucio13

[gucio13]

Thanks for all advices.
It works now again.
What I did:
1) made new null modem cabel: only pins 2-3,3-2,5-5,chasis
2) set serial interface on PC:57600,8,no,1,no
3) laptop and db800 with patch cabel to router
4) dreamUP start - mark network and start connect
5) hold power button on db800, then power on (220V)
6) start flash
7) after flashing ready , switch of/on

later I was also able to change image over dcc software (network)

unfortunately my SATA HDD WD3200BEVT will not be recognized
(checked with linux pc - is 100% ok)
but dm800 says : no hd connected

some ideas ?

[romy]

try this
hope it will help

[abualferas]

i have same problem but ethernet cable does not work what ishould do i think i screwed my dm800

[seyal30]

I have tried all the solutions even boght a second DM 800 to try combined solutins but with no luck been tring to see the images to fix "file to big" but got nothing but the restrection of this site coulde any body help please ?
can you send me the IMAGES ?

[ovydik]

And I have the same problem with File to big.
Please help me, guys!

[phara0n]

OPEN DreamUP
CHECK USE NETWORK
PRESS CONNECT
CONNECT ur dreamBox NUll Modem and LAN Cable must be mounted, u will get an IP Adress, after CA 2nd stage not found and nothing happen
Open Browser, be patient it will get a moment to OPEN and then u will have the Upgrade Firmware option available, then flash like before ur DM 800

[Kan-G]

I have flashed with serial Cable using the Tool Universal DreamUp 1.3.3.4 (only this version is working on my Dreambox!)
After you can flash a Dreambox Image but only one with the right Drivers for the Fake DM800!

[عدنان قاروط]

i have the same problem
but i cant do any think
????

[dalton565]

Do you have to have a lan lead connected when using dreambox if your using a serial cable ?

[southpaw]

Do you have to have a lan lead connected when using dreambox if your using a serial cable ?
yes mate , both

[vienn07]

Hi, I need some help. I have downloaded 2nd stage_pack for my dm800 hd clone. Okay first up my connection is usb to rs232 to the dreambox and ethernet cable from my modem to my dreambox. Well i think i did everything right and even enforce the flash but i still am having the File to big error. By the way when i hold the silver button and on the power to my dreambox it states error no ca found. Anyway can please help me out here.

[Bulld0g]

Hi, I need some help. I have downloaded 2nd stage_pack for my dm800 hd clone. Okay first up my connection is usb to rs232 to the dreambox and ethernet cable from my modem to my dreambox. Well i think i did everything right and even enforce the flash but i still am having the File to big error. By the way when i hold the silver button and on the power to my dreambox it states error no ca found. Anyway can please help me out here.
.
Try and get access to a pc with an RS232 port on it. Some people can flash from a laptop using the usb RS232. I have never been able to manage this. Also try it with a crossover cable if you've been using a staight ethernet.

[Mik018]

i have this problem too, only thing is i have null modem cable but when i turn Dm800 it starts uploading flashloader and when its completed,it says "upload completed, waiting for aknolagde", and on dm800s display i get an error msg "Error1: no ca found"
look at www.dm7020.com (http://www.dm7020.com)

I dont get a chance to upload second stage loader to dreambox
what couold I do ?

[Lert]

I tried all the solutions here but not work for my DM800. I used normal LAN cable connect PC to router. Do I need to use crossover cable? Do I also need to use crossover cable connect DB to router?

[jopie]

Hello Satfriends
I have tried to flash my 800Hd and get the error no ac found I have lookt on this board and find a lot to resolve but I have tried everything but cant get a IP adres and with the Dreamup he load all then get again the same error.
Is there sombody can help me with this
Thanks in Advance
Jopie
Spain

[iubito]

Hello

I still get the "File to big!" error....

Please give an idiot recipe... :)

I

[nickneyime]

Hello

I still get the "File to big!" error....

Please give an idiot recipe... :)

I


Yes my brother,

pleace help us

[paul1974]

did any one come up with the fault file to big i ve tried all methods and still not working

can i take my working dm800 and put the sim in there and then flash the bootloader

also is the bootloader on the sim card?

[acimate]

Hi, I need some help. I have downloaded 2nd stage_pack for my dm800 hd clone. Okay first up my connection is usb to rs232 to the dreambox and ethernet cable from my modem to my dreambox. Well i think i did everything right and even enforce the flash but i still am having the File to big error. By the way when i hold the silver button and on the power to my dreambox it states error no ca found. Anyway can please help me out here.


Hi buddy, saw your pm, read this thread,
http://www.digital-kaos.co.uk/forums/f34/fix-no-ca-error-70341/

it will definitely solve as i have tried no only once, but few times. :rock:

[vienn07]

hi buddy, Well i actually tried all method but it didnt work. In the end i send the box back to my supplier and he fix it. hehe

[scannacs]

I also had the "file to big" error.

But I found a way around it.
First of you need the null modem cable and the "broken" box need to be connected to the network.
Second use the patched version of Dreamup included in the zip file in romy's post.
http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/index4.html#post556129

Start the patched DreamUp. Make sure network is checked (enabled) and next push the Connect button.
Then power up your dreambox. Upload should start.
After the upload the "No CA found" message should appear. Don't click OK and no need to start enforcer or DM800_repair.
INSTEAD open a browser and go to the ipnumber of the dreambox (it is on the display of the box)
The bootloader webinterface should appear and you can flash the box from there.

It worked for me, I hope it will work for you too.

Good luck,
Scanner

[johan_s]

Any solution to this? I have tried everything but stills gets: File to big! when I try to flash from DreamUP.

[palmy]

My DB was crashed so badly that it corrupted the bootloader (power on the DB and it displays "error" in less than 1 second. I managed to use RS232/LAN method to revive the bootloader and subsequently my entire box.

http://www.digital-kaos.co.uk/forums/f34/fix-no-ca-error-70341/index2.html#post703161

[alexxx304]

hello people :D
im geniuse;]
you must click extras and make recovery whem recovery endd, have you flash button and you can flas dm800:D
sory but i don'T speak english

[Kango]

hi, newbie here.

Recently just bought two sets of dm800hd-c. Set A comes with working image(Gemini version 5) and auto-keys. Set B only come with working image.
Can i use dreamup V1.3.3.4 to do a backup file for set A, and then flash the file to the set B so that Set B will also has working image (Gemini v5) and auto key?
Or can i use other alternate method to upgrade my set B?

[givaracom]

i have a problem wafter flashing a clone dm 800 error display, cant use rs 232 to flash with dramup

[BM300]

OPEN DreamUP
CHECK USE NETWORK
PRESS CONNECT
CONNECT ur dreamBox NUll Modem and LAN Cable must be mounted, u will get an IP Adress, after CA 2nd stage not found and nothing happen
Open Browser, be patient it will get a moment to OPEN and then u will have the Upgrade Firmware option available, then flash like before ur DM 800

Hello,
I get the IP address but cannot get the browser to logon to DM800 IP no matter how long I wait.
Tried both normal Lan and twisted cable.
Can log on to the web without any problems.

Thanks

[Bulld0g]

Is your firewall turned off ?

[BM300]

Thanks for your help,

Turned the firewall off , allowed the browser to pass the filter.

Still no luck.

Regards

[BM300]

Thanks for all your help and great tips friends.

I used part of every method shown in this thread,
So credit goes to anyone who shared with us his/her experience.

The aim of the exersise is:
A- To get an IP address and load it into the Web Browser
B- To reflash the DM800 with a fresh nfi image or Bootloader.


This is how I got it to work with the clone unit that I have:

1- Connected Null modem Cable (9 pin RS232) to DM800.
2- Start DreamUp.
3- Connect power to DM800 while holding down silver button on DM800.
4- Wait for DreamUp to load.
5- If you get the Error message about no 2ndstage CA found, (repeat the steps 2-4 until you get an IP address on the DM800 screen).
6- I have an 8port switch connected to my router, so all my connection was to the switch instead on the Router.
7- Connect computer to switch using Cross LAN cable.
8- Connect DM800 to switch using normal LAN cable.
9- Power up DM800 while holding down the front silver button until Dream Multimedia or STOP is displayed.
10- Start up your Browser (I used Firefox).
11- Enter the IP address that you got from DM800 into the Browser ( e.g. http://192.168.0.125)
........Wait for the special loading screen to come up.
12- Select firmware upgrade.
13- Select location of the file location that you want load from your computer and click on Flash.
14- Wait for the blue scale to finish loading on your browser.
15- You can restart your DM800
or
16- flash it with a bootloader of your selection then restart DM800.

Good Luck

[hurry]

doesn't work for me

always have message ERR01: NO CA FOUND on my dreambox when i turn power on with RS232 cable plug and dreamup running.

i'd tried the 2nd_stage_pack and when i click on flash, choose my file, i have the File too big message.

Help me please.

[Arraysys]

doesn't work for me

always have message ERR01: NO CA FOUND on my dreambox when i turn power on with RS232 cable plug and dreamup running.

i'd tried the 2nd_stage_pack and when i click on flash, choose my file, i have the File too big message.

Help me please.

"ERR01: NO CA FOUND" tell you that your CLONE box cannot run the original image. You need a NULL Modem and Ethernet cable connected and the Dreamup application running in connecting mode before power on the box. Once the box turn and acknowledge a NULL Modem cable attached you will enter the flashing mode and shouldn't see "ERR01: NO CA FOUND". You will see the "found dm800hd box" at the Dreamup application windows.

CAUTION: Check your cable.
NOTE: You should use a RS232 NULL Modem cable not just RS232 cable. There are different type of RS232 cable.

[Ruszti]

Dm800 clone sim2.01 ss75 is down!
I used repair but can?t flash SSL only whit SS72
Begin to boat and not finish eni ever
Need Help to com up to SS75 or ?
Best regards
Ruszit

[Arraysys]

Dm800 clone sim2.01 ss75 is down!
I used repair but can?t flash SSL only whit SS72
Begin to boat and not finish eni ever
Need Help to com up to SS75 or ?
Best regards
Ruszit

You may try this image, come with SS76C
SGStarhub Digital-Kaos Image - Page 216 (http://www.digital-kaos.co.uk/forums/f34/sgstarhub-digital-kaos-image-39241-post794139/#post794139)

[aleqs]

Information Product Name ??? Booloader version Dreambox Second Stage Loader BUILD #59, built 20080509 Flash Size 64 MB Production Date (YYYY/MM/DD) N/A mID ? Serial Number ? MAC Address ? Printed Serial Number ? That whats shows in the web interface of my box , is it totally ruined ?

[kaka13]

Information Product Name ??? Booloader version Dreambox Second Stage Loader BUILD #59, built 20080509 Flash Size 64 MB Production Date (YYYY/MM/DD) N/A mID ? Serial Number ? MAC Address ? Printed Serial Number ? That whats shows in the web interface of my box , is it totally ruined ?


hi,

just old version flash (2008/2009)

rgd

[halim2731]

Having bad nightmare flashing the clone DM800, I managed to get it done. Using Dreamup version 1.3.3.4, firstly run dreamup, click connect button, connect Rss232 null cable modem to your box, anyway I did connect my network cable also to run together, and at this point connect you dreambox power supply without power on and press power button on your dreambox and on the power supply and wait until half of the green bar on dreamup show and only then you release the power button on the dreambox, and here you can see after finishing the button flash will show, and here you just click flash and locate the nfi file to flash on..here you go, with happy ending.

Note:- At the early stage My dreambox 800hd display error message. and with the above mentioned text I managed to get it done. Please note that do not release the power chrome button on the dreambox until a least half of the green progress bar on the dreamup being done.

[Xelmep]

Dear All,
Please everyone who solve the problem "file to big!" , Please help us how to solve it too, what to do, what to install with dreamup, bootloader or ex. any gemini firmware, or something else ???

Thank you.

[trajceski]

I tried to upgrade my sim1 to ferrari sim but after installation of ss78 my DM800 suffered the same problem of: EFF01 on display;
than no CA found and after using the ex "file to big"


please help!!!

[toninio]

Why can not I have access to those photos: (
I have the same problem because Uploader today to my dreambox 800 hd clone, and an inadequate soft reboot Dreambox Oled display appeared to me 'NO CA FOUND? please some sensible advice, whether it can still be saved :(

[miajdk]

Work perfekt Thank you!
Dm800 clon alive again :-)

[evanjaf]

If you have bought an 800 recently and come against some problems with flashing then this might be the fix for you

I was told my box was 75 bootloader but ok for 72 aswell i tried to flash and got the ' NO CA FOUND '

Some times it would boot up with dreamup in 'serial http mode' but could never find a working IP and failed when trying to flash,

The rest of time it would boot up in dreamup with the 'NO CA FOUND SeCOND STAGE BOOTLOADER' this would allow me to use enforcer but came up against the 'FILE TOO BIG' problem

If you have problems like these try my method below it worked for me
does this method works on win7 64bit via usb converter

[henny58]

sorry for the post in dutch.

pm me for help with the problem and i send you some files like a patched dreamup from forhike that worked for me

[evanjaf]

Am glad this is helping guys here, took me 5 days to crack it lol
i have been trying this for nearly a week now, file to big error is doing my head in, i even reinstall fresh copy of windows no joy @all is there is any other method apart from above to try
many thanks

[evanjaf]

sorry for the post in dutch.

pm me for help with the problem and i send you some files like a patched dreamup from forhike that worked for me
i done bit by bit the above method no joy any thing els you recommend please
thenks

[evanjaf]

Dear All,
Please everyone who solve the problem "file to big!" , Please help us how to solve it too, what to do, what to install with dreamup, bootloader or ex. any gemini firmware, or something else ???

Thank you.
hi did you menage to revive your box

[azizan8]

File too big problem during flashing. Anyone can help?

[azizan8]

I also had the "file to big" error.

But I found a way around it.
First of you need the null modem cable and the "broken" box need to be connected to the network.
Second use the patched version of Dreamup included in the zip file in romy's post.
http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/index4.html#post556129

Start the patched DreamUp. Make sure network is checked (enabled) and next push the Connect button.
Then power up your dreambox. Upload should start.
After the upload the "No CA found" message should appear. Don't click OK and no need to start enforcer or DM800_repair.
INSTEAD open a browser and go to the ipnumber of the dreambox (it is on the display of the box)
The bootloader webinterface should appear and you can flash the box from there.

It worked for me, I hope it will work for you too.

Good luck,
Scanner

The problem is web browser got error when u open it. Once No Ca error, IP didn't shown at Dreambox. Then, there is no way you can flash it. For me, I can connect dreambox using Dreamup however I still cannot open the browser using the IP of dreambox as shown in Dreamup. Now, the bottom line is how to solve the error of "file too big".

[pirx]

starting dream up, connecting power to dreambox, null modem cable in, Lan out, Lan boot unchecked in Dream up,
In info window of Dream up message DM 800 and nothing.
When use flash enforcerer got message file too big. When do this with Lan in and Lan checked in Dream up option nothing.
In browser connection is timed out.
Dreambox display error!
DM is dead - any sugestion?

DM800 HD PVR,
desktop with serial
Lan wired
router

[hengch88]

Start the patched DreamUp ,select entras / recover bad sectors & start DM800_repair

If u can see "bad sectors been marked" . U can flash the image now. Try it.

[azizan8]

Information on Null Modem Cable

Null Modem (http://www.nullmodem.com/NullModem.htm)

[meterizi]

use either null cable and ethernet connection ...

[dave2014]

This problem really stressing me :-( I have the err01 No CA Found)
I have managed to flash a new image several times and still the error occurs, I have also flashed new bootloader and again error occurs, I think I have tried every tut available. Dont know if it makes a difference but this is a new clone I bought with latest M tuner to replace previous dm800 with glitching hd channels, the older dm800 always flashed fine first time

[Arraysys]

This problem really stressing me :-( I have the err01 No CA Found)
I have managed to flash a new image several times and still the error occurs, I have also flashed new bootloader and again error occurs, I think I have tried every tut available. Dont know if it makes a difference but this is a new clone I bought with latest M tuner to replace previous dm800 with glitching hd channels, the older dm800 always flashed fine first time

Are you talking about the new DM800PRO Satellite Receiver which come the Tuner: HIG003 REV:M (HD channel 8PSK/QPSK Symbol rate 1-45M/S)?

For "err01 No CA Found" most likely related to the image software that you are using to flash. Can I ask whether where you get the software image? Was the software being patched for CLONE dm800? Or have you ever try to patch after flashing with original software image.

[dave2014]

Are you talking about the new DM800PRO Satellite Receiver which come the Tuner: HIG003 REV:M (HD channel 8PSK/QPSK Symbol rate 1-45M/S)?

For "err01 No CA Found" most likely related to the image software that you are using to flash. Can I ask whether where you get the software image? Was the software being patched for CLONE dm800? Or have you ever try to patch after flashing with original software image.

Yes it is dm800 satalite with the tuner you refer to Its a clone, i got it from dvbseller), i am not sure if it is a pro as it was just sent out as a direct relacement for my other dm800 which glitched on hd channels. I get my images from dm800sim2.com and yes they are pre patched (I think). I was unsure where to get original images. I just used the images I used on my previous dm800 as they flashed easily on that one with no problems, can pre patched images not be used now as I? This is the image I prefer to use and which I had on previous dm800 UNOFFICIAL DREAM ELITE V.133DV3 PHOENIX EDITION. Can you reccommend a solution


Thanks for your reply

[dave2014]

I have now managed to get it to boot into an image using bl69, if i try any other bootloader I get the no ca error again. Image boots up but when it gets to where the tuner config page should be it gets "system error hardware could not be verified", Please any ideas anyone, i will move this to the correct satallite section, sorry

[Bonesy]

I have now managed to get it to boot into an image using bl69, if i try any other bootloader I get the no ca error again. Image boots up but when it gets to where the tuner config page should be it gets "system error hardware could not be verified", Please any ideas anyone, i will move this to the correct satallite section, sorry



"system error hardware could not be verified", related to the image you putting on have the genuine dreambox plugin installed where it checks if the dreambox is a clone or not.

[dave2014]

I have managed to get box working now with another image, but still my box will not boot up with anything other then bl69 even though originally it had bl76. As for the Genuine Dreambox plugin, this always says "security service not running" even though box is now working, obviously something is a miss or corrupt in my box, i just do not know what :-(

[Persian]

please help to me i have problem file to big!!
i use Enforcer.exe and but not ok!

[dave2014]

When you power up your dreambox and dreamup starts uploading the basic bootloader let the blue progress bar get atleast half way and then press flash, should let you flash whatever image/bootloader you want then. Hope that helps

[mus2007]

my dreambox 800 hd dead. no display, no ip, when i try to flash box is given me FILE TO BIG FIX error. plz help

[dreamteam666]

Thank you but still file to big error I need help thnx

[dreamteam666]

someone can Help pls thank you

[Bulld0g]

Thank you but still file to big error I need help thnx
make sure your flashing the correct bootloader in the image for your box.

[beebee31]

Ok with help from Superman at supersatshop this is what i done and it worked

connect dreambox to router
use crossover cable connect router to laptop
open dreamup
connect null modem
connect power to dreambox while holding silver power button till dreamup has fully loaded
find IP of box (i used dcc) mine edded up being a very strang 192.168.1.6
put this in dreamup
open enforcer
load image and flash


I have found the Gemini images are useless as i done all above and it failed to boot up again so best to use another i have nabilosat and all is fine here

Again thanks Superman for your hours of help

I wish to buy the dm800, and who should i get from and must 1 do anything to it when it arrive in singapore?

[rondiamond]

I had some serious trouble trying to get my dm800 running again with these no ca error & file to big errors.
I had upgraded my sim card to ferrari using the 'free-ferrari-upgrade-1-1.nfi'. This had been working fine for a few weeks, until I flashed the wrong image this is when I first got the 'no ca error'.
I tried flashing all sorts of images and bootloaders but the 'no ca error' wouldnt go away.

In the end I connected via serial and lan cable. Ticked use network in dreamup and flashed the 'free-ferrari-upgrade-1-1.nfi' back to my box, by entering the ip address on the screen of my box and displayed in dreamup int my web browser. At first it hung on dhcp while booting up. i removed the network cable and rebooted. This time it booted up properly, I ran the ferrari upgrade tool from the plugins menu. It said upgrade successful. I now rebooted and could flash a new ferrari image again. Maybe this is of use to somebody

[diviqm]

yesterday i was have success with dead dm800 clone SIM2.01
i use SSL76D-20101219.nfi loader and then without reseting you can load image witch you want.Use second stage pack and full cros RS232 cable.
Both method work well.
The problem with error NO CA found and FILE IS TOO BIG make me crazy all three days .
THE BIG PROBLEM of clone DM800 is simcard holder - there is no good contact with sim.I was press and hold on the simholder and then start dreamup - all errors is go on.Card slot is loose and can not pressed well to contact pins.

[ultrakiasu]

I am assisting my colleague to get his clone DM800HD to work.
Very weird behaviour compared to the other DM800HD i had recovered earlier.

This time, the DreamUP does not response, no detection, no dialog box pop up complaining "No CA..."

Was told he had use DreamUp to replace the shipped TGP firmware with DreamElite sim2.01, and dont like the layout, and flashed some firmware downloaded from OpenPLI, and got stucked since.

Tried the DMM logo clicking fix, Tried Enforcer..
Cant get even an IP at all..

I am totally lost.. anyone able provide a solution?

Thanks in Advance

[abeltcb]

I have similiar problems as you. still not able to solve. I sent back to china for repair due to com port no response.bootloader have not reach the com port state.


I am assisting my colleague to get his clone DM800HD to work.
Very weird behaviour compared to the other DM800HD i had recovered earlier.

This time, the DreamUP does not response, no detection, no dialog box pop up complaining "No CA..."

Was told he had use DreamUp to replace the shipped TGP firmware with DreamElite sim2.01, and dont like the layout, and flashed some firmware downloaded from OpenPLI, and got stucked since.

Tried the DMM logo clicking fix, Tried Enforcer..
Cant get even an IP at all..

I am totally lost.. anyone able provide a solution?

Thanks in Advance

[frevo]

To All, if u having problems file to big the cable is not connected used a good null cable
Yesterday I bought 2 and no one works!! So with dream UP use a good cable!:idea:

[mtv1]

hi m8 what dreamup are you uising try this one Digital Kaos - Downloads - Patched Dreamup (http://www.digital-kaos.co.uk/forums/downloads/other/8/patched-dreamup-1395/) hope this helps :)

[ultrakiasu]

I am assisting my colleague to get his clone DM800HD to work.
Very weird behaviour compared to the other DM800HD i had recovered earlier.

This time, the DreamUP does not response, no detection, no dialog box pop up complaining "No CA..."

Was told he had use DreamUp to replace the shipped TGP firmware with DreamElite sim2.01, and dont like the layout, and flashed some firmware downloaded from OpenPLI, and got stucked since.

Tried the DMM logo clicking fix, Tried Enforcer..
Cant get even an IP at all..

I am totally lost.. anyone able provide a solution?

Thanks in Advance


I found the solution for myself..
Sharing is Caring..

What u need:
1) 1 working DM800HD
2) 1 null modem cable
3) 1 working LAN network link
4) 1 PC

Connect the working DM800HD to DreamUp without the network option.

Once the DM800 detected, wait till the Flash button to be un-greyed.

Unplug the current null modem cable and reconnect to the powered-off faulty set, and plug in the LAN cable.
Plug in the power to the faulty unit.

Wait for 30sec and click flash.
The OLED will display the ** Serial Setup Mode **
And also display the DHCP obtained IP

Use the web interface to flash the patched firmware.

Enjoy!!

Newbies, don't PM me for details, I wont reply.
Just read more on the commonly available steps yourself.

The above procedure is for those who had issue with non-responsive DreamUp recovery.

[stemag]

I have just bought a dm800HD PVR, it locked up on the 3:d day I owned it, and wouldnt boot, so I tried to flash it threw webbrowser.
Now I dont have an IPadress or anything, it just shows the display:"Dream multimedia ->Error! NO CA FOUND, look at www.dm7020.com (http://www.dm7020.com).

I saw this link, and it seems to have the solution for me, but I cant see the Pitures (1.jpg.....) until I registred, so thats wat ave done now.
Sorry my English, I?m from Sweden.

//Steve

[zuu]

Hello, I'm new here and newbie with clone 800

I'm from Georgia and sorry for my English

yesterday become DM800 as gift (used one), with some very slow arabic Gemini on board. Checked the BL version and it was BL73. I have changed the image with this one:

Merlin-2.Excalibur_OE-1.6-dm800-20101010_SIM_BL70_OCP.nfi

After one day testing found some problem with 4-5 DVB-S2 transponders on 9E. via telnet checked again the BL version and it was 76r1.

after image OpenBlackHole DM800 - I have the same problem - "File to Big"

so, which image can I use with my damaged sim?

via WI I have uploaded my old Merlin-2.Excalibur_OE-1.6-dm800-20101010_SIM_BL70_OCP.nfi - NOT WORKING, same error - NO-CA

can someone share BL72 file? (a small file, only bootloader)

[Arraysys]

Hello, I'm new here and newbie with clone 800

I'm from Georgia and sorry for my English

yesterday become DM800 as gift (used one), with some very slow arabic Gemini on board. Checked the BL version and it was BL73. I have changed the image with this one:

Merlin-2.Excalibur_OE-1.6-dm800-20101010_SIM_BL70_OCP.nfi

After one day testing found some problem with 4-5 DVB-S2 transponders on 9E. via telnet checked again the BL version and it was 76r1.

after image OpenBlackHole DM800 - I have the same problem - "File to Big"

so, which image can I use with my damaged sim?

via WI I have uploaded my old Merlin-2.Excalibur_OE-1.6-dm800-20101010_SIM_BL70_OCP.nfi - NOT WORKING, same error - NO-CA

can someone share BL72 file? (a small file, only bootloader)

Try this, is a BL72 image
Hotfile.com: One click file hosting: dm800-NB11EN-sim2.rar (http://hotfile.com/dl/109264453/a9583cd/dm800-NB11EN-sim2.rar.html)

[danielmor]

me too same problem file to big??
please help



I hope I can access the images after this post ;-)

[Arraysys]

me too same problem file to big??
please help

Try to flash with another image. It could be wrong image.

[ultrakiasu]

File too big, usually meant, write access denied.

[miss123456]

DM800 NO CA FOUND/FILE TO BIG FIX (http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/index10.html#post1010089) help me pls!!!!!!!!!!!
sim is a 1.0 and write bootloader 59

[asternight]

I am writing to discuss the same issue, no dreamup be no recovery and gone. Last resort .. I hope
to see the photos.

[asternight]

I am writing to discuss the same issue, no dreamup be no recovery and gone. Last resort .. I hope
to see the photos.

dm 800 pvr sim 2.01

[payos]

Hello I am new to the community, I am interested in how to fix this big omfg problem (the famous no ca found). So I am desperate as you all.
I tryed many combitnation and even if my box respond to the flash and dream up say ok to me I still have the problem :_)
can anyone help :_)

[payos]

Hello people :-)

Good news I found how to flash the pain in the Azz from the famous ca not found (dreambox 800hd pvr)...

You will find on the pages above some patched dream up
and some files that may usefull but for me it work differently... here the story

1)Open dream up

2)you will need a null cable modem and a network connection (rj45 via router in my case).plug the r232 cable

3)connect dream up

4)power on your dreambox 800

5) once you will see that your box is connected you can identify on the boxscreen the ip address

I know even if the network should not work, once you get hooked via the r232 cable(null modem) it will be ok

6) go on a web page and write the IP address

7) MOST IMPORTANT PART...LOOK at THE BOOTLOADER YOU NEED...it's at the end of the text on webpage

in my case it was a #59 so here is the link for an image
Officiel Image ( 500 s / 800 HD ) By soirnet.com (http://forum.soirnet.org/showthread.php?4066-Officiel-Image-%28-500-s-800-HD-%29-By-soirnet.com)

It seem's that even if an image(firmware) is good the bootloader is your viagra

7)Then do the upgrade firmware and flash it

8) A brand new working box


I still need to get used to the cccam and stuff as it's just two days I started playing with dreambox

Hope it will work for you folks and et me know
see ya

[dema2]

Hi dear friend for to solve this error " no ca found" very simple::
use a native rs232 serial port, nullmodem cable
software you find "dream up patched" on google
find and download all second stage for your dream box 800hd clone, you will need to say wath sim card have on board, there is clone like mine that have sim 2.0.1, other with FERRARI CARD, the more older box have sim 2.0.0 or sim 1.0.0, download all second stage ssl 69 to 76d download all for ferrari ssl78f or all that you find, i have more of this pm to me i send, weel now repeir

connect clone dm800 to serial port with null modem cable, dm no connect power
open the soft dream up patched click connet, this ask to you to give on the clone dm 800hd, insert power, wait, soft charge the loader, about 2 minutes, after load the your Second stage no firmware complete, only the your second stage, flash, in about 5 minutes your dm is now in a new life, is ok... for any question ask to me , i do not have experience in chip tuning, i study from now..., but i am in sat from 1998...good work and repair
best regards to all dema2 italy :beer:

[dema2]

Hi dear friend for to solve this error " no ca found" very simple::
use a native rs232 serial port, nullmodem cable
software you find "dream up patched" on google
find and download all second stage for your dream box 800hd clone, you will need to say wath sim card have on board, there is clone like mine that have sim 2.0.1, other with FERRARI CARD, the more older box have sim 2.0.0 or sim 1.0.0, download all second stage ssl 69 to 76d download all for ferrari ssl78f or all that you find, i have more of this pm to me i send, weel now repeir

connect clone dm800 to serial port e null modem cable, dm no connect power
open the soft drean up patched click connet, this ask to you to give on the clone dm 800hd, insert power, wait, soft charge the loader, about 2 minutes, after load the your Second stage no firmware complete, only the your second stage, flash, in about 5 minutes your dm is now in a new life, for any question ask to me , i do not have experience in chip tuning but i am in sat from 1998...good work and repair
best regards to all dema2 italy :beer:

[nemirno oko]

hello I have spent much time reading the forum for
* ERR01: CA NO FOUND
and I have not found an adequate answer in this regard, I hope someone has solved for this. When I turn on the receiver to the mains electric. network connections back of boxes in the same second you turn yellow and green lights for 2 seknde the display appears err01: no ca found. I used all DreamUp did not help. only when I connect dramUP 1.3.3.1. 232 cable message appears 12:12:11 box type: DM800 you can wait a year nothing was happening? I used to post here hipertrminal (c) 2007.2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1:00 BO23456 {}

2ND STAGE OK, build # 76 (20,100,419)

0000 - BCM board setup
00000126,00000126,00000125,00000124,00000123,00000 133 {}
0007 - fp init
0008 - ca init
CA invalid
OLED found!
NO CONFIGURATION DATA PRESENT. STOP.
* ERR01: CA NO FOUND
I hope to have a solution thanks

board REV J
tuner REV K

SIM 2.01

If there is a way help ppppp

[Oshie]

I've got the same problem what is the reason?

[nemirno oko]

There is no reason for this I can not understand that that it will not start DreamUp

[deffc0n]

Problem is Hardware :)

[nemirno oko]

which part should be replaced

[v2vboni]

I need help, my DM800 HD PVR is not booting anymore it just keep showing the NO CA FOUND error.

*The problem, I did flash it with a wrong .nfi or firmware, but before I did that, it was detecting a DM7020 as firmware though my unit shows DM800 HD PVR.

Now, I need to know which firmware or bootloader to use with my clone DM800 HD PVR. Hope you could provide me the files and steps to identify. My SIM inside shows: WT00 3588

[gheribrahim]

pretty simple fix , mine took best part of an hour using null cable and crossover together , good luck

[SGDVB]

Why an hour? If using dreamup + null modem + straight lan should only be less than 5 minutes to flash an image for DM800.


pretty simple fix , mine took best part of an hour using null cable and crossover together , good luck

[aldawsee]

I FOUND SOLUTION FOR ( FILE TOO BIG)
guys use another dreamup software
i used ver 1.3.3.7
u can find it here
http://www.dreambox.it/tools.htm (http://www.dreambox.it/tools.htm)
search for it


ok the steps are as posted befor
1. unplug the dm800 and conected to pc usin serial cable
2.run dreamup new version and click concect and dont close it ever.
3. plug ur dm800 to power now u see flash when it finish ( all slots (green) pring dreamreapir in front of dream up to inable the flash button and then press dream logo so u can flash ur dm with ur boot loader. also kepp dream repair or inforcer running.
4. now u see the screen on ur dm800 showing diffrent signs i saw dhcp...>
5. plug the network caple so the dm800 show u ip on the led screen u can plug it erlier in step 3.
6. use the ip to flash ur dm with an image and now use ur web browser.
then ur dm800 is alive againe

[africatwin]

Hi buddy, saw your pm, read this thread,
http://www.digital-kaos.co.uk/forums/f34/fix-no-ca-error-70341/

it will definitely solve as i have tried no only once, but few times. :rock:

hi Bro, anyway to flash DM800 without having the CA error coming out?

[ultrakiasu]

hi Bro, anyway to flash DM800 without having the CA error coming out?

First, you must understand why the error appear in the first place.

If you bought the original non-cloned DM800, the bootloader is preloaded in the official Enigma2 firmware, and required conditional Access (CA) cards to work. The Dreambox DM800 is protected by a security chip is designed to stop clone builders from selling receivers which can run the enigma based software which runs on these boxes.

Obviously the clone makers had their own SIM cards which make loading of enigma software on their clone sets possible.
Thus there is a need to make the firmware to load drivers for these special SIM card.

As long the firmware u had flashed included the bootloader driver for the matching SIM card (1.0 or 2.01), then you should not have the CA errors.

[arseven]

Me too with same problem.

I appreciate you guys help, since i'm around this subject for many hours and nights.

CA NOT FOUND error appears when i flashed wrong image. After that, following suggestions from here, i tried to flash with null modem and lan cable. The error changed to
LOOK AT WWW. DM7020.COM
CA NOT FOUND

I bought my 800 clone with indication from seller that would have ferrari sim card ssl78f. Now I have some doubts about that since on the clone screen, when in http mode, is shows the message
FERRARI SIM CARD SSL76FF

Also on the webinterface, at the bottom of the screen where firmware upgrade is made, it is written:
Bootloader Version: Dreambox Second Stage Loader BUILD #59, built 20080509


I tried DreamUP_patched_by_forhike_and_natas and many other dreamups, getting error
"No CA found by 2nd stage loader, please contact support at dream-multimedia"
When i tried enforce, flash button is highlighted,I choose image, but I get error FILE TOO BIG
I think this error appears because dreamup disconnects himself.
With these dreamups, i get an ip adress on the screan, what allows me to try webinterface.

By webinterface, Flash runs untill the end (100.00 %) but when i restart clone, the error LOOK AT WWW. DM7020.COM persists on the screen

With dreamup 13.3.3.6 and 1.3.3.7, I don't get error, but after uploading flashloader, it stops in
UPLOAD COMPLETED, WAITING FOR ACKNOWLEDGE
if i force flash with enforce or dm800repair, i get
WAITING CHECKSUM and stops here. With these dreamups, i dont have any ip adress on the scren to try web interface

These is a complete report of what i'm facing...

What am i doing wrong?
The image i'm trying to use is for ssl76

I don't know what to do more

Regards to you all !

[DreamersDVB]

I've done quite a number of DM800 CA ERROR and solved with enforcer or patch dreamup without a problem. Theres 1 one set(DM800)recently i have done everything like what you did,but still fail. Last option what i did was, swap simcard from my working box to the ca error box..And you know what the faulty box start and running again..I just need to either Dreamup v1334 or use lans cable>ip>mozilla>and flash newnigma2 bl82 image..Done as a Happy Man.



Me too with same problem.

I appreciate you guys help, since i'm around this subject for many hours and nights.

CA NOT FOUND error appears when i flashed wrong image. After that, following suggestions from here, i tried to flash with null modem and lan cable. The error changed to
LOOK AT WWW. DM7020.COM
CA NOT FOUND

I bought my 800 clone with indication from seller that would have ferrari sim card ssl78f. Now I have some doubts about that since on the clone screen, when in http mode, is shows the message
FERRARI SIM CARD SSL76FF

Also on the webinterface, at the bottom of the screen where firmware upgrade is made, it is written:
Bootloader Version: Dreambox Second Stage Loader BUILD #59, built 20080509


I tried DreamUP_patched_by_forhike_and_natas and many other dreamups, getting error
"No CA found by 2nd stage loader, please contact support at dream-multimedia"
When i tried enforce, flash button is highlighted,I choose image, but I get error FILE TOO BIG
I think this error appears because dreamup disconnects himself.
With these dreamups, i get an ip adress on the screan, what allows me to try webinterface.

By webinterface, Flash runs untill the end (100.00 %) but when i restart clone, the error LOOK AT WWW. DM7020.COM persists on the screen

With dreamup 13.3.3.6 and 1.3.3.7, I don't get error, but after uploading flashloader, it stops in
UPLOAD COMPLETED, WAITING FOR ACKNOWLEDGE
if i force flash with enforce or dm800repair, i get
WAITING CHECKSUM and stops here. With these dreamups, i dont have any ip adress on the scren to try web interface

These is a complete report of what i'm facing...

What am i doing wrong?
The image i'm trying to use is for ssl76

I don't know what to do more

Regards to you all !

[arseven]

Thanks for your answer.

If i well understand, you put a simcard from a working dreambox to the one with the problem.
Then she started working.
What you done next?

You stay with the dreambox which didnt have the problem sotped because don't have simcard, you bought another simcard, or you manage to use the simcard which was in the broken dreambox?

Just to know what should I do. Maybe I have to buy another simcard, since I don't have any other dreambox.

Someone knows where to buy?

[SGDVB]

The sim 2.01 is not commonly sold as local seller will not get them unless they have very good relationship with their source.

Even that most source in china are basically reseller & not direct distributor or factory. Only those who work with the factory may have chance to get hold of the sim.

I may be wrong as your source could be a big time reseller but to what I know, there are only a few of them.

Even you search on website selling DM box, the assy they sell only the tuner, adapter, remote. Not the sim card.


Thanks for your answer.

If i well understand, you put a simcard from a working dreambox to the one with the problem.
Then she started working.
What you done next?

You stay with the dreambox which didnt have the problem sotped because don't have simcard, you bought another simcard, or you manage to use the simcard which was in the broken dreambox?

Just to know what should I do. Maybe I have to buy another simcard, since I don't have any other dreambox.

Someone knows where to buy?

[SGDVB]

Sorry... I did not see your this post.

You are on ferrari sim? Please note that you can only use ferrari patch image & not the sim2.01 image.

Clone box commonly use sim2.01. Ferrari sim is a total failure which the chinese try to come out to counter sim2.01 but they have fail.

Sim2.01 has been widely known & has it full support by many other in term of patch image.


Me too with same problem.

I appreciate you guys help, since i'm around this subject for many hours and nights.

CA NOT FOUND error appears when i flashed wrong image. After that, following suggestions from here, i tried to flash with null modem and lan cable. The error changed to
LOOK AT WWW. DM7020.COM
CA NOT FOUND

I bought my 800 clone with indication from seller that would have ferrari sim card ssl78f. Now I have some doubts about that since on the clone screen, when in http mode, is shows the message
FERRARI SIM CARD SSL76FF

Also on the webinterface, at the bottom of the screen where firmware upgrade is made, it is written:
Bootloader Version: Dreambox Second Stage Loader BUILD #59, built 20080509


I tried DreamUP_patched_by_forhike_and_natas and many other dreamups, getting error
"No CA found by 2nd stage loader, please contact support at dream-multimedia"
When i tried enforce, flash button is highlighted,I choose image, but I get error FILE TOO BIG
I think this error appears because dreamup disconnects himself.
With these dreamups, i get an ip adress on the screan, what allows me to try webinterface.

By webinterface, Flash runs untill the end (100.00 %) but when i restart clone, the error LOOK AT WWW. DM7020.COM persists on the screen

With dreamup 13.3.3.6 and 1.3.3.7, I don't get error, but after uploading flashloader, it stops in
UPLOAD COMPLETED, WAITING FOR ACKNOWLEDGE
if i force flash with enforce or dm800repair, i get
WAITING CHECKSUM and stops here. With these dreamups, i dont have any ip adress on the scren to try web interface

These is a complete report of what i'm facing...

What am i doing wrong?
The image i'm trying to use is for ssl76

I don't know what to do more

Regards to you all !

[tganet]

I Have same proble, how to resolve this !!


TGAnet

[alexys44]

Hi guys! Same problem with a DM 800hd...i have tried several times Dreamup(2nd_stage_pack_Flicksters Magic Files) all technics and nothing_receiver connected with PC via Serial cable_db9(null modem),network cable to router(anyway no net connection at all_blocked)...Results:ERR01:no CA found!on the box display and"file to big" when trying to flash with Dreamup__seems no comunication between pc_dreamup_and receiver...Please someone help me !!!

[alexys44]

The error came after a webinterface image install image was ok but after the first reboot ,the box displayed the error ! I have tried to install a new image(DreamElite) because the box was very slow and heating to much(i used a cooler against heating_tuner!)...probably because of an old image installed by the seller...Thanks very much for help !Best wishes to all !

[dwrath]

I got a dm800hd. Ran the online upgrade and turned out it was a clone set. Now stuck with said error

[lanimal]

i ve the same problem does any know where to fing second stage uploader in NFI that is no too big to load

thanks
:bawling:




I still have "file to big" after your procedures!
What can i do?

[Lee1501]

FIXED for me !!!! Hi all, I had the file too big error for days, I eventually discovered that the fault was the serial cable I was using. I bought from ebay a NULL MODEM serial cable. (See ebay item 180481856158) With this cable, I didn't even need to use the enforcer program, dreamup worked as expected, it immediately recognised the box, the status bar increased and the flash button became available automatically. This time when I selected the file, it DID NOT report a file too big error. I'm very happy!

by the way. I plugged this cable in to a USB to serial convertor, and flashed with a modern laptop with USB ports only and no serial port.

I hope this helps

[paresh]

Dear folks!

I have a cloned 800 SE and it is now showing this error "R01: NO CA FOUND". Yes I did system update last night and today it is broken (yes my fault and it serves me right!).

So what I have done so far to fix this:
1. Searched on the internet and found these tools and lots of recommended steps
2. Dreamup Tool
3. Downloaded 210-SSL82-LT7-Patched-By-Ferret-dm800se-20000101.nfi
4. Connected the DM800se to my lapton using USB service port behind the DM800se and other end to the laptop USB interface.
5. My Windows 7 detected the new port and installed all the drivers. The device is a Port - Silicon Labs CP210x USB to UART Bridge (COM4)
6. Rebooted Windows 7 machine
7. Switched off DM800se
8. Start Dreamup Tool
9. Click Connect and it connects
10. Ticked Box "Use Network"
11. Local IP (PC) shows my laptop IP address
12. Select one: I have selected my laptop IP address
13. Remote IP (Box): Blank because the existing IP is not even issued to any device!
14. Serial Port: COM4
15. Switch On DM800se
16. DreamUp finds the box and does some flash upload (this takes only 20 seconds or so)
17. It than gives me a message stating "Waiting for Acknowldgement..."
Thats it!
18. I have tried using the Dreamup Force version which enables the Greyed out Flash button etc... but with that I get another message "File too big!"

Ok I give up! **Please can some help me**.

Also some of the blogs mentions Modem Null Cable? Well on 800se you dont have the Modem Null Cable but only service port (USB) connection.:bawling:

[yassinov]

Too much Steps on the classic method !
OptiFlasher make it easy for you !


-Run OptiFlasher
-Click Advanced
-Select Port
-Select Model
-Write Bootloader or Repair NO CA Found
-Do Job


regards , yassinov

[tv 800hd for sg]

How about the problems can be SG DVB PM.

DM800HD DM500C DM500 V Dm800se new configuration***12290;

[flyingp1g]

This d@mn err01 no ca is killing me. I cant get my dm800 to connect for no reason. The serial port is not communicating no matter what. I've tried all version of dreamup patched and not, ive changed 3 different computers, 2 cables (100% sure its null) null/null, null/usb, ive tried them all, also optiflasher,NFC, enforcer, everything.
I think its a faulty rs232 port on dm800, but again not sure.
Is there anyway to get to stop ip mode, jtag or anything???
Please help:saint:

[Decoder]

This d@mn err01 no ca is killing me. I cant get my dm800 to connect for no reason. The serial port is not communicating no matter what. I've tried all version of dreamup patched and not, ive changed 3 different computers, 2 cables (100% sure its null) null/null, null/usb, ive tried them all, also optiflasher,NFC, enforcer, everything.
I think its a faulty rs232 port on dm800, but again not sure.
Is there anyway to get to stop ip mode, jtag or anything???
Please help:saint:

Hi flyingp1g I'm no expert (as you'll see from my posts!!) but are you sure it's null modem - I had same feelings till I went to M*pl*ns and bought what I knew to be a "proper" null modem cable. Was also missled with usb to adapter (didn't know how to tell computer/Dreamup what port it was using) but my new computer has 9 pin port - plugged new cable in and bingo away she went!! Also don't forget you seem to have to have the network cable plugged in when using Dreamup. Hope this gives you some help. Best wishes

[flyingp1g]

Ok this is how i solved the no ca found with my dead rs232 port.:beer:.
I connected a working dm800 with patched dreamup with only serial mode, but on dreambox both serial and lan connected. After dreamup loaded, i unplugged the working dm800 and plugged the broken one with again both serial and lan on dreambox and when it powered up it went in serial mode with ip showing. Then i flashed it with a correct image through web browser (not dreamup anymore) and works great. Serial port still not working so i guess its dead.
Very important dreamup only in serial mode, when i tried it with both serial and ethernet mode it didnt work.
Thanks

[aristote12000]

Help me
My 800hd Is out
When open Dreamup patched and connect I have this message:
FILE To BIG

?????????

[azir2981]

Is it working for all BL59, BL 62 ETC...
thanks

[Ome Merde]

I've got the same problem over here
no matter what I try, the error is back after every reboot
cable is 100% ok

if I bootup (for the use with dreamup), check "use network" I can access the webif. I can flash an (old) image but it hangs at aprox. 45.70%

I've been busy for 5 days now, I'm fed up with it

regards,
merDe

[Ome Merde]

just fixed it !!

what I did (in my case, old dm800hd (sim1(?))

* download dreamup and secondstage-dm800-69.rar which can be found at the following link : http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/index11.html
* connect the box with the crosslinked serial cable and network
* prepare the connection, switch on the box and wait for the error
* a bootloader was uploaded
* close dreamup, power-off the box
* download optiflash 1.0.6 (google) and make a serial connection
* choose "write bootloader", click "do job", follow instructions
* networkcable must be attached, type the ip-address
* choose in the following screen "secondstage-dm800-69.nfi" (downloaded before)
* afther finished, poweroff box, hold button on the box, poweron
* oi, dhcp is working again
* open browser (IE8 in my case), navigate to image to flash. I choose an old ssl69 image, just for testing. GP2 with ssl69 worked for me, can be downloaded at Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/UNBAHBR71Y)
* flash it by the webinterface
* reboot after finishing and grab yourself a cold one

tomorrow I'll try to update to a more recent image. my five days of agony are over so far


merDe

[mete61]

whats the new dreamup 1334 or is dare a new

[Zepic]

Which version of dreamup do you need?

[Mirfa]

Can anybody help me with this error msg "Error1: no ca found? please

[leppard]

flash bootloader then it will be working

[jokkeri77]

just fixed it !!

what I did (in my case, old dm800hd (sim1(?))

* download dreamup and secondstage-dm800-69.rar which can be found at the following link : http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/index11.html
* connect the box with the crosslinked serial cable and network
* prepare the connection, switch on the box and wait for the error
* a bootloader was uploaded
* close dreamup, power-off the box
* download optiflash 1.0.6 (google) and make a serial connection
* choose "write bootloader", click "do job", follow instructions
* networkcable must be attached, type the ip-address
* choose in the following screen "secondstage-dm800-69.nfi" (downloaded before)
* afther finished, poweroff box, hold button on the box, poweron
* oi, dhcp is working again
* open browser (IE8 in my case), navigate to image to flash. I choose an old ssl69 image, just for testing. GP2 with ssl69 worked for me, can be downloaded at Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/UNBAHBR71Y)
* flash it by the webinterface
* reboot after finishing and grab yourself a cold one

tomorrow I'll try to update to a more recent image. my five days of agony are over so far


merDe

Thanks so much for this!!! It helped me revive my DM800 (it says SIM 2.01 at the back).
I had the CA not found error, and couldn't get various versions of Dreamup to work (the patched version said file too big, and 1.3.3.8 got stuck at "upload complete - waiting for acknowledge".
I tried the "Repair" option in the Optiflash tool, but that didn't work (no CA found error after reboot). But the "Write Boot-loader" option in Optiflash has become my hero, was able to flash the SSL-84b from another site, and after reboot, my old image booted fine (btw also the GP2 5.1 bl69). I think I will need to flash another image at some point, but I'm too tired now after ages of troubleshooting.

Hope this helps someone.

[mrwok]

Too much Steps on the classic method !
OptiFlasher make it easy for you !


-Run OptiFlasher
-Click Advanced
-Select Port
-Select Model
-Write Bootloader or Repair NO CA Found
-Do Job


regards , yassinov



i try this one lot of time no START 1.8 had no dm800se ferrari suport "NO ca FOUNDDDDDDDDDD"inside

is there on this planet ONE person who explane THE BIG file bug and lot of people have the same shit!!!!!!!!!!!
dm800 is no problem ca no found because rs232 cable is hard flash(you know) and usb is soft shit.
Is the trick "pc-->rs232 cable--adapter-->mini usb-->dm800se?????????????"Make test please i have not this cable.

THE person who makes my dm800se ferrari alive is "The Besttttttttt"

[mrwok]

good job only works with dm800 ----->Dm800se have mini usb no ca found is then hang on BIG FILE SHIT ssl62,ssl69,ssl enz is too BIG is there one people on this planet its TIME to MAKE this BIG bUG for lot of people FINished

TANKS

good job fixed my no ca!!

[bilon]

Hello, I have a problem with my dreambox 800pro with sim210 (clone)
when i try flash my dreambox, dreamup show me message that file is too big, i try to different bootloaders and ssl and still same message file to big, what am I doing wrong??
Maybe someone can tell me what i need to use, second stage loader or bootloader and which one??
Thanks

[cassano82]

Tnx...I hope to solve with this method ... I have the Dreambox Second Stage Loader BUILD # 59

[mide2008]

i have a clone dm800 hd. Pls how can i determine the sim number on my dm. On opening it up i only saw a plain white sim nothing on it.

[checkersceltic]

hi guys, i have the same problem.
oled display reads no c a found.
so far i have used dreamup then enforcer.

so far i have managed to highlight the flash button but when i try to flash all i get is file to big!!!!!!!

please can anybody help its now been 2 days and about 100 posts read but still cant seem to get a solution
help help help
all the best

[checkersceltic]

hi there i seem to have the same problem as yourself, i have seen your thumbnails but i cant figure out what you did to resolve it. can you please explain what you did to a bnovice like me!!! thanks in advance

[mongje]

also file to big issue
how can i know if i use the right null modem cable?

[khristos]

If you have bought an 800 recently and come against some problems with flashing then this might be the fix for you

I was told my box was 75 bootloader but ok for 72 aswell i tried to flash and got the ' NO CA FOUND '

Some times it would boot up with dreamup in 'serial http mode' but could never find a working IP and failed when trying to flash,

The rest of time it would boot up in dreamup with the 'NO CA FOUND SeCOND STAGE BOOTLOADER' this would allow me to use enforcer but came up against the 'FILE TOO BIG' problem

If you have problems like these try my method below it worked for me

any help?
/10chars

[Jossies]

I have a similair problem.
When starting dreamup and turning on my dm800 clone, nothing happens. Not even the boxes name comes up.
Dm's display says: error01 no ca found and it stays that way.

nullcable is good, used it on a different db.

when using a different debug version it give a hardware break error.

thats all i get.

Can someone explain me if there is anything i can do?

Thx ;)

[mcwago]

DM800HD bl59, no clone -> NO CA FOUND
first repaired over NCF CA repair.
i've uploaded secondstage-dm800-69.nfi from
Index of /diverses/secondstageloader/dm800 (http://www.i-have-a-dreambox.com/diverses/secondstageloader/dm800/) over Optiflasher and now the dm awaiting dhcp :)

[khristos]

Okay I download all the files you guys suggested, also did from several other forums too.

I have the patched dreamup both versions.

I use a com connection and an ethernet to router/ethernet to PC. None of them works

When I start the dreap up, it connects, when I try to flash I always get teh file to big error. I trid several firmwares but no luck still the same message and I dont know what else to do.

DM 800 HD PVR
Version sim 2.0.1

No idea if its clone or not.

Any help what goes wrong here? The file too big is always there and QUITE annoying.

Please help somehow.

[jorgesipp]

hi,

can anyone tell me where to download the enforcer please?

thanks a lot

[stinguss]

thanks but the problem is always there I can't reflash my clone DM800

[timigo]

The same problem, "No CA found by 2nd stage loader + big file", I can't send the image by dreamup and the network is locked, any ideas? Thanks.

[ram3322]

I have the same probleme
Error1 No CA FOUND
DREAMBOX DM800 HD PVR
Help

[DBTraitor]

fix(read here)

DreamOEM - NCF SIM2 V2.1 Updates (http://www.dreamoem.com/content.php?200-NCF-SIM2-V2.1-Updates)

[asus9]

Hi

For those who have problem with the NO CA FOUND problem dont give up on trying. Last few days I was having that problem,I bought a few cables but it doesnt solve the problem

I have tried usb to usb cable, rs232 to usb, rs232 to rs 232 but not to availability. Other than that, I have tried the dreamup, ncf, optiloader software but still cannot detect my dm800hd and I personally recommend to you all to make your own null model cable and find an old pc/laptop that has rs232 port.

The things required to make a null modem cable is by using this diagram (http://digital.natinst.com/public.nsf/$CXIV/ATTACH-AEEE-82HQFA/$FILE/Strait%20Through.jpg). I just need 2 x rs232 connector, wires, solder to make the null cable.

After using the null modem cable, I used ncf software to fix the problem and within a minute the problem is solved

[Manator]

please any sollution? i have no ca../file to big and im not able to use com or network seems to be locked .. any help please?
used all the metods arround and still no luck

i have a dm800hd pvr sim210

please help

M

[Manator]

The same problem, "No CA found by 2nd stage loader + big file", I can't send the image by dreamup and the network is locked, any ideas? Thanks.


hello mate

i have the same problem i cant connect by null cable or network and big file problem ..do you ever fixed the problem?
i have test everything with diferents programs and no luck ..any help would be priciate

BR
M

[atifpervaiz28]

look at www.dm7020.com (http://www.dm7020.com) no ca found error how to fix

[zcchmos]

just using 3 week dm800hd pro having problem on sim card 2.1 pls help me if any options to copy and rewrite simcard. Already confirm this simcard defect after flash no ca found and try another sim to fix on tis box can be dream up.:stupid:

[zcchmos]

Thank for reply,

1.My dm-pro already tried dreamup fail & check null cable ok on my dm500s.
2. Use hyperterminal also no respond.
3. Using good box to broken dm800hd (dreamup enfocer) also stuck no boot. but the sim are diffrent good one sim 2.01
4. If i swap same sim card from good dm pro ver sim 2.1 no problem can dream up.
5. finally find out this sim having a problem and any body can teach me how to recover the sim 2.1 card problem.
6. Confuse..why dm800 dreamup boot on 2nd stage (sim card) and not inside EPROM ic.like dm500s. pls advise.

Thanks,

[redcity82]

Recently brought DM800HD PVR, now the screen show Error- No CA found. Can anyone guide me how to solve this problem?

[ultrakiasu]

Recently brought DM800HD PVR, now the screen show Error- No CA found. Can anyone guide me how to solve this problem?

Did you tried using Google before asking question here?

A simple search using "No CA found" give me so many links to the solution.

[pokolpek]

dm 800 69 secondstage bootloader need...

[ichristos]

let's see if this thing works...


Hope to solve this tomorrow. I'm happy to see there are helpful people out there.
New on this!!!

Thanks.

Reeeaaalll Happy.
Everything works.

You find the solution in this:

Digital Kaos - Downloads - dreambox enforcer (http://www.digital-kaos.co.uk/forums/downloads/other/8/dreambox-enforcer-990/)

I used a twisted serial and port 1 in dreamup

[Boxfresh]

Hope to solve this tomorrow. I'm happy to see there are helpful people out there.
New on this!!!

Thanks.

Reeeaaalll Happy.
Everything works.

You find the solution in this:

Digital Kaos - Downloads - dreambox enforcer (http://www.digital-kaos.co.uk/forums/downloads/other/8/dreambox-enforcer-990/)

I used a twisted serial and port 1 in dreamup

^This is just what I needed. Fixed!

[DBTraitor]

Dreambox NCF Repair Tool SIM2 EDition v2 - YouTube

Download the program here
http://www.digital-kaos.co.uk/forums/downloads/other/8/dreambox-no-ca-found-repair-tool-sim2-edition-v2-5-2061/

[nakno]

still having this problem

[eang18]

still having this problem

Hello,
Could you open the box and take a picture of the box internals and the SIM card (it should be near the antenna). Pm me with the pics hence I can check and advise further.

[DBTraitor]

Digital Kaos - Downloads - Dreambox NO CA FOUND Repair Tool SIM2 EDition V2.5 (http://www.digital-kaos.co.uk/forums/downloads/other/8/dreambox-no-ca-found-repair-tool-sim2-edition-v2-5-2061/)

[hiphin]

I have DM800PRO (clone DM800 HD PVR) with "no ca found".

REV:M printed onboard
SIM is DM800 12422 SIM210

help me, by telling me with what image should I try to flash...

[DBTraitor]

you confirm your box is for SG use?
Over here we only use 800hd-c

anyway, there is a video on top. Have you followed the steps. Have you got your null modem cable?

[hermanmaier]

have the same problem with a box here - dream up is saying waiting for acknowlegde but this shows CA error :-(

[frank087234]

I have DM800PRO (clone DM800 HD PVR) with "no ca found".

REV:M printed onboard
SIM is DM800 12422 SIM210

help me, by telling me with what image should I try to flash...

I got same error after flashing wrong image, sim 2.01 clone
Any ideas?.

[dlegrand]

same problem, thanks

[reddy]

same here, tried flashing for a friend and it shows this fault after flash and i'm sure the image is working as it was a backup from my working SE.

From what i understand, My friend claims that the clone that he just bought came with original Sim, so can use the original image from Dreambox. ( Not sure how true is that??.) Could this be the issue? Not compatible with images suitable only for clones??. i have returned the box to my friend, so cannot test it out now..

[uu161]

same here, tried flashing for a friend and it shows this fault after flash and i'm sure the image is working as it was a backup from my working SE.

From what i understand, My friend claims that the clone that he just bought came with original Sim, so can use the original image from Dreambox. ( Not sure how true is that??.) Could this be the issue? Not compatible with images suitable only for clones??. i have returned the box to my friend, so cannot test it out now..


ur friend are right there is A8P sim original clone sim in market for DM500HD and DM800SE
already out for mths and flashing any original image only
clone image will not work on A8P sim

[reddy]

ur friend are right there is A8P sim original clone sim in market for DM500HD and DM800SE
already out for mths and flashing any original image only
clone image will not work on A8P sim


Alamak, like that jialet, so must now clear the CA fault first , then download original images only to flash in , then put in bouquet.

Then only will be solved right?. Susah lah!!!... Dunno why people want original for??...

[uu161]

Alamak, like that jialet, so must now clear the CA fault first , then download original images only to flash in , then put in bouquet.

Then only will be solved right?. Susah lah!!!... Dunno why people want original for??...

Yes and original image will be better no more green screen issue doing any update

[reddy]

Yes and original image will be better no more green screen issue doing any update

Ok, thanks for advise..
Try to look for original images first.

I hope the web browser methods and dreambox edit do not have any other restrictions surprises later..

Haha!!

[matp123]

Hi All

im losing the will to live. ive trawled through the forum's and im failrly sure ive gone though every page on the internet to no avail

due to stupidity on my part i now have to reflash my dreambox.

i have tried various versions of Dreamup and get as far as flashing the memory. After an hour or so it just sits there saying box is flashing from memory,

when using the 3.2.4 image. ive have tried various others and either get the same message or " Invalid Image "

i get no " all complete " or " ok" messages. i even left it over night. when i disconnect the null modem connection and restart the box it goes straigh back to No CA Found.


im now out of ideas.

Any help much appreciated

[mctouf]

I will try this

[yusufak]

cant seem to find a solution Im stuck with it

[halim23]

here the same problem. Dreamup is not working...

[fayroumf]

what about the dm800se hd come with sim a8p?
is it same as sim 2.0

[niels4545]

thx helped a lot!

[melvillecook]

Hi there, I have a CLONE Dreambox DM800 HD PVR and it has the SIM210, when I turn it on ALL I get on the screen is DREAM MULTIMEDIA -> ERROR! ERR01 NO CA FOUND, I have downloaded and tried dreamup, I have tried to flash it and when I connect the cable and link it to my PC and try and flash it, it says FILE TO BIG. PLEASE HELP, thanks

[Decoder]

Hi melvillecook Think your problem is you've flashed with wrong image (err01 No CA Found) what I have found is make sure you have box connected to internet, computer hard wired (reversed/crossed cable) run latest Dreamup, get box IP address, open browser on computer and then put IP address into address bar and when found (the box) you can Flash correct software. Are you sure 800HD has SIM210 as my 800HD has SIM2.01 and my 800HD se has SIM2.10? Hope this helps and you get it sorted, best wishes

[Decoder]

Hi fayroumf No mate they are not the same SIM. With the A8P SIM you can ONLY use genuine software and the SIM2.10 is for CLONE software ONLY

[Nichola5]

Anyone still here? Im new and I've got problem flashing my dreambox DM 800 HD PVR. It shows Error: no CA found and when I use enforcer, I says file to big :(

[fooklee]

Reboot your PC and connect again