Freelander 2004 mileage correction with upa

[calin_bm]

I want to work on this dash ,the dash has inside MC912,i understand that it can be read/write with upa by solder the 4 points behind the dash,can anyone post a picture to see where is the connection and what pins on Upa must be connected?
Thank you.

[gepakg]

this MCU on freelander always secured,must be desoldered to etl,or UPA hc912 adapter,or in circuit with rosfar!

regards Gepa


I want to work on this dash ,the dash has inside MC912,i understand that it can be read/write with upa by solder the 4 points behind the dash,can anyone post a picture to see where is the connection and what pins on Upa must be connected?
Thank you.

[drpeter]

I want to work on this dash ,the dash has inside MC912,i understand that it can be read/write with upa by solder the 4 points behind the dash,can anyone post a picture to see where is the connection and what pins on Upa must be connected?
Thank you.

Don't have time now to look for UPA pins but here is schematic. I help you later when I have more time

[alldecode]

I have same problem and UPA USB not working with this dash, but year is 2001, it is locked too?

[drpeter]

I have same problem and UPA USB not working with this dash, but year is 2001, it is locked too?


Yes, I don't think you can do this car with UPA you need to program on a certain frequency, Rosfar R260 is the only way.

[gepakg]

also tried with desoldering MCU and read it with UPA hc912 adapter and ETL work fine,but need desoldering..

regards Gepa


Yes, I don't think you can do this car with UPA you need to program on a certain frequency, Rosfar R260 is the only way.

[calin_bm]

yep,desolder,but the real problem is the needles,when you mess with them you will have hard times trying to put them bach in place...

[PremierD]

yep,desolder,but the real problem is the needles,when you mess with them you will have hard times trying to put them bach in place...

Correct me if I'm wrong mate ....2004 in the picture above ...MCU is on the back no need to remove needles ....

[maucontacto]

Hi!!!

And about 912D60 from 2001? UPA, ETL and Rosfar on circuit don?t read.

BR
maucontacto

[maucontacto]

Hi!!!

And about 912D60 from 2001? UPA, ETL and Rosfar on circuit don?t read.

BR
maucontacto

Solved!!
Rosfar and direct connection on pins

[antibisic]

Is it possiblle to read this mcu with X-prog m because in the software is not this mask included only under Hc912D60A 112 pins secured?Regards

[mario313]

Yes, use Xprog-m no problem.

[justy22]

Is the mcu easy to de solder how many pins does it have, anybody have a pic

[PremierD]

Is the mcu easy to de solder how many pins does it have, anybody have a pic

"Hc912D60A 112 pins secured?Regards "

[antibisic]

Yes, use Xprog-m no problem.


But what adapter to use? In clone box is not bdm adapter which has coaxial cable inside or can use normal cable with same pinout?

[mario313]

Use HC12(S) BDM adapter. I have original, but clone Xprog-m have too BDM adapter.

[calin_bm]

correct me if i'm wrong,i think it's the same with the micronas adapter?

[dfi]

correct me if i'm wrong,i think it's the same with the micronas adapter?

Yes, it's the same adapter, but you only need it if processor is secured

[calin_bm]

anyone worked with this metod?any pictures?

[antibisic]

thanks for your reply

[bonux]

Hi, i also confirm that UPA-USB clone works with freelander secured mcu, you just need sorder it on bdm board. No need to remove needles also.

[Meat-Head]

Don't have time now to look for UPA pins but here is schematic. I help you later when I have more time

Did you manage to find them, please?


Hi, i also confirm that UPA-USB clone works with freelander secured mcu, you just need sorder it on bdm board. No need to remove needles also.


Cool, you got the info.

THIS IS A GENUINE JOB - NO ODOMETERS WILL BE INCORRECTED, need to swap out a faulty speedo head.

Does anybody know if plugging in a used speedo will wack out the milage in BCM?

THANKS

Meat (in a pannick)

[smartymarti]

They don't sync with each other mr meaty head , so you'd have to incorrect vcm , but on a 2004 no one is gonna be concerned

[Meat-Head]

incorrect vcm , but on a 2004 no one is gonna be concerned

VCM?

It's a genuine job, i'll plug the 2nd hand set in tomorow see what it says

car is for sale, advertised as whatever.

Just if he new speedo is way out, need to set back to what it is - hear that Justy22 - set back not IN-corrected.

UPA setting? This is secured has does upa sort that?
What settings on xprogm?

Thanks

Meat

[PremierD]

Your ****ed with upa meaty .. unless you bought the adaptor .. it MCU is bdm locked so need to be removed to read ..unless you have r260 or similar ..don't have Xprog so dont know about it

[Meat-Head]

it MCU is bdm locked so need to be removed to read ..unless you have r260 or similar ..


Right, so your saying remove the MCU stick into upa adaptor - (china clone) no idea what they were off hand.

It's a fuel gauge fault - ign on, spins around like a roulette wheel.

Not confident it's more than just the motor, but looks like it a pig of a job to swap over.

Thanks.

[Music73]

what year is meaty.. is it the early 2001 - 2004 or the 2004 - 2006..

[jarecki55]

I make 3 x freelander belong 2 week time. I tray Xprog, UPA and R270. Every time after correction dash go dead, I don't know why but xprog and R270 made by china do errors by writing(verification ok) but dash don't wake up, or problem on fuel gauge. I make backup read flash and eprom, after few attempts dash back to live, but make my mad.
I looking for freelander solution :)

[Music73]

I make 3 x freelander belong 2 week time. I tray Xprog, UPA and R270. Every time after correction dash go dead, I don't know why but xprog and R270 made by china do errors by writing(verification ok) but dash don't wake up, or problem on fuel gauge. I make backup read flash and eprom, after few attempts dash back to live, but make my mad.
I looking for freelander solution :)

I have only done one of these, used a R260 clone (red 9s12) work first time with no errors or removing MCU, Just connected Via BDM Port.

Got mine from banny @ revtronic

[Meat-Head]

2004 - 2006..

2005 same as this thread http://www.digital-kaos.co.uk/forums/f174/landrover-freelander-2005-pinout-283811/#post1643183


, or problem on fuel gauge. read flash and eprom, after few attempts dash back to live, but make my mad.
I looking for freelander solution :)

This is the problem the fuel gauge spins like a roulettre wheel


Ia R260 clone (red 9s12) work first time with no errors or removing MCU, Just connected Via BDM Port.

Got mine from banny @ revtronic


Wicked, how much?

[Music73]

From Greebid ?115 + p&p
cas3 912x 9s12x in circuit programmer (http://www.greebid.com/wholesale/cas3-912x-9s12x-in-circuit-programmer-697.html)

from Banny think it was ?230, but you have somewhere close to speak to if you have a problem.

[Meat-Head]

WICKED, thanks to the kind DK member who IN-corrected this for us.

It was ONE mile less than it should have been, so need to do this:-

The member says it wans't a secured one?

Won't argue, not my money, not my car!

http://www.digital-kaos.co.uk/forums/members/81877-meat-head/albums/testing/5946-edited.jpg

[justy22]

Meaty Thanks for my jump leads special eeprom ones as well, im trying to decide what to get you, any ideas anyone



WICKED, thanks to the kind DK member who IN-corrected this for us.

It was ONE mile less than it should have been, so need to do this:-

The member says it wans't a secured one?

Won't argue, not my money, not my car!

http://www.digital-kaos.co.uk/forums/members/81877-meat-head/albums/testing/5946-edited.jpg

[Meat-Head]

Meaty Thanks for my jump leads special eeprom ones as well, im trying to decide what to get you, any ideas anyone


Err what you on about mate?

[justy22]

Err what you on about mate?

got an early christmas present, set of jump leads with eeproms stuck to them and a to/from on an 24c08 with a message and a further wrapped up was a timerand a aa battery meant to look like a bomb

you and tam must be behind it LOL

[Meat-Head]

got an early christmas present, set of jump leads with eeproms stuck to them and a to/from on an 24c08 with a message and a further wrapped up was a timerand a aa battery meant to look like a bomb

you and tam must be behind it LOL

:roflmao::roflmao: Sorry mate, you lost me there.

Timer, bomb? Is it possable and ONLY a possable, was NOTHING nasty at all, but infact a digital clock off say a freeview arieal. That might have been IN-correct - just needed winding back?

http://www.taiwantrade.com.tw/MAIN//resources/member/1374/productcatalog//f52bd987-6a98-432c-b375-aaec69591c67_p_080328_02555.jpg


Maybee on Xmas Day somebody will start a thread about what presants we got, upload photos. Sadly i'm going to be off-line most of Xmas Day & *HATE* starting new threads.

[PETAR]

Is it possiblle to read this mcu withr270 whit out problem?

[vokinn]

Done one today with rosfar260
couldn't find mcu mask in r270

[PETAR]

ok thanks
what programator can i use for this dash?
i dont have rosfar

[vokinn]

I guess you can use xprog or etl but not sure if you can can read it in circuit wit etl

[PETAR]

wiil work x prog good whit this dash in circuit?
because i heve x prog

[vokinn]

Yes just use rosfar diagram and nyo4 to calculate km from eeprom dump