Audi S3 8V1 - 300HP VR File

[DJSNAKE2]

Hello everyone,

I have an Audi S3 8V from 2013, engine code : CJXC with 300HP EU Spec

I would need VR File from it, please :D

VIN nr.: WAUZZZ8V4EA105902
Engine: 2.0l R4 TFSI
HW Ver.: 06K907425A
SW upg.: 8V0906259 0006
Installation: SC1.1 CB.00.00.Y0 C01.00 SC1

Many thanks guys!

Have a nice day

[tyzyano]

Here is ORI file from Disport
8V0906259 0006

[DJSNAKE2]

Here is ORI file from Disport
8V0906259 0006

Many thanks bro!! I will try later today :)

[tyzyano]

Pay attention to correct file, not the same for all tool, if you send me your read I back to stock it or if you want do your self, restore part from hex 40000 to A8620 of my file

[DJSNAKE2]

Pay attention to correct file, not the same for all tool, if you send me your read I back to stock it or if you want do your self, restore part from hex 40000 to A8620 of my file

Well, it's the good file size & region data since I have another ORI file from another S3 same year/engine but different SN.

If anyone is willing to share their file too so I can compare, it will be very much appreciated :)

[tyzyano]

Well, it's the good file size & region data since I have another ORI file from another S3 same year/engine but different SN.

If anyone is willing to share their file too so I can compare, it will be very much appreciated :)

What tool you use to flash?


Inviato dal mio iPhone utilizzando Tapatalk

[DJSNAKE2]

What tool you use to flash?


Inviato dal mio iPhone utilizzando Tapatalk

KessV2 Clone 5.017

[DJSNAKE2]

Update :


I decided to buy the Tactrix OpenPort 2.0 and use VW_Flash (on Github)
It's faster to write (approx 20sec) instead of full write with KessV2 clone (15 min) and you can also log the car via live data.

You still need ORI file to use it. (VW Flashdaten for official software update on VAG cars)

VW_Flash can do Simos 12, 12.1, 18.1 etc aswell as TCU (DQ250 DSG6 for me) :)

[carmageddon]

is possible to use on windows? how to do setup?

[DJSNAKE2]

is possible to use on windows? how to do setup?

I'm using Windows 10, there's a tutorial on the Github page for Windows installation !
You need the Tactrix interface to use the software.

[carmageddon]

i have tactrix genuine…but i understand nothing about how to do to run under window this software…want you explain please?

[crouchinggerbil]

i have tactrix genuine…but i understand nothing about how to do to run under window this software…want you explain please?

Tactrix original is not all that great, there are better passthru vcis out there.

It will work on almost any j2534 passthru vci that supports the STMIN_TX IOCTL.

Download the release version with the gui https://github.com/bri3d/VW_Flash/releases/download/v0.6.0/VW_Flash_GUI_v0.6.0.zip

[DJSNAKE2]

i have tactrix genuine…but i understand nothing about how to do to run under window this software…want you explain please?

Looks like crouchinggerbil answered faster than me :)


Tactrix original is not all that great, there are better passthru vcis out there.

It will work on almost any j2534 passthru vci that supports the STMIN_TX IOCTL.

Download the release version with the gui https://github.com/bri3d/VW_Flash/releases/download/v0.6.0/VW_Flash_GUI_v0.6.0.zip

Anyways, I have Ali version of Tactrix and no issues at all, I don't know if genuine is good or not

You just gotta download the zip file and put everything in a folder and just run the software, then you follow the tutorial here (https://github.com/bri3d/VW_Flash/blob/master/docs/windows.md)

[carmageddon]

ok....all clear....one question, have you tried on windows 7 if this software is working? i tried on w7 and w10 but work only under w10

[carmageddon]

Update :


I decided to buy the Tactrix OpenPort 2.0 and use VW_Flash (on Github)
It's faster to write (approx 20sec) instead of full write with KessV2 clone (15 min) and you can also log the car via live data.

You still need ORI file to use it. (VW Flashdaten for official software update on VAG cars)

VW_Flash can do Simos 12, 12.1, 18.1 etc aswell as TCU (DQ250 DSG6 for me) :)


now...where you start to flash car? need frf to unlock ecu? the checksum is automatic during writing? please, can you explain step by step how you do writing? thanks

[carmageddon]

sorry i see now the tutorial on github, the only thing that i dont understand is checksum.....is automatic during writing by the tool?

[DJSNAKE2]

now...where you start to flash car? need frf to unlock ecu? the checksum is automatic during writing? please, can you explain step by step how you do writing? thanks

So basically, you can't read that ECU anyways, you gotta make a "Virtual Read" file yourself using the software.
Then, you unlock the ECU, that what's taking long time

Finally, when you done that (including writing back original file), when you use the software, you should only use Calibration Flash Unlocked since it's only writing the modified part of file in the ECU!

For example, you have a .TXT file in your PC, you wanna change a sentence in the .TXT file, instead of rewriting the whole file with your edit, you just edit the sentence :)

[carmageddon]

ok, thanks....and for the checksum correction? the tool made correction during writing?

[DJSNAKE2]

ok, thanks....and for the checksum correction? the tool made correction during writing?

Checksum should be automatic when writing using Calibration Flash Unlocked, otherwise, you can just fully write your original file and bring back the ECU to locked mode like nothing happened.
Simos ECU's can't be bricked, they're smart enough to get it back in working state!