View Full Version : Immo off for Ford Fiesta 1999 - 25040
ghkarim
23rd May, 2012, 03:12 PM
Hello,
Costomer have original key, Red lamp still ON.
He prefer to turn immo off to forget this problem for ever.
Thank you,
dichar
23rd May, 2012, 04:00 PM
reference ecu is bosch ME7.1 ??
jairpg21
23rd May, 2012, 04:10 PM
can you send a picture of pcb?
ghkarim
23rd May, 2012, 04:21 PM
reference ecu is bosch ME7.1 ??
don't know if it's bosch , no label on ECU exept stiker that I joined.
regards
ghkarim
23rd May, 2012, 04:22 PM
can you send a picture of pcb?
picture joined
jairpg21
23rd May, 2012, 05:36 PM
Try removing this memory, in some ford you can immo off just doing this, please report
ghkarim
23rd May, 2012, 05:43 PM
Try removing this memory, in some ford you can immo off just doing this, please report
will try and report
regards
ghkarim
23rd May, 2012, 09:04 PM
removed mcu but didn't work.
>Thank you for advice,
Still waiting for other solution -))
Dane-Elec
23rd May, 2012, 11:07 PM
removed mcu but didn't work.
>Thank you for advice,
Still waiting for other solution -))
Make a new key,or try to sincronyse again ecu, dash and key, as i know is not possible to make immo off on that type of ecu.
Dane
keygargoil
24th May, 2012, 03:28 AM
is the light on solid when the ignition is on or flashing if it is on solid then either the pats needs initialising or if it has been reset 3 keys need cycling in
micromax
24th May, 2012, 07:43 AM
if you have (ti) texas instruments mcu in plcc try this, work on many variants of EEC-V
ghkarim
24th May, 2012, 09:24 AM
Make a new key,or try to sincronyse again ecu, dash and key, as i know is not possible to make immo off on that type of ecu.
Dane
With wich tool can I resynchronize ECU? Or is there any manual procedure ?
regards
ghkarim
24th May, 2012, 09:25 AM
is the light on solid when the ignition is on or flashing if it is on solid then either the pats needs initialising or if it has been reset 3 keys need cycling in
The light still solid ON when I turn ignition ON.
Can't get comms with tester to reprogram keys.
regards
ghkarim
24th May, 2012, 09:25 AM
if you have (ti) texas instruments mcu in plcc try this, work on many variants of EEC-V
haven't TMS mcu in ECU. :-((
Dane-Elec
24th May, 2012, 10:35 AM
The light still solid ON when I turn ignition ON.
Can't get comms with tester to reprogram keys.
regards
Hi
Use IDS.
Dane
micromax
24th May, 2012, 04:17 PM
sbb can programm key. what is this IC?
ghkarim
24th May, 2012, 05:35 PM
sbb can programm key. what is this IC?
Sbb connect but can't get security access.
Number of key in memory = 0
after read DLC =
ERR9213 :
Key programmed less then minimum required.
Tried to reprogram new keywith SBB but can't get security access after 800s.
regards
yssf
24th May, 2012, 10:27 PM
For ford You'll need outcode to incode to get access to program key.
Find another tool m8,for this fault u can reprogram key and job done
ruscic
22nd June, 2013, 04:46 PM
hello,
is there any solution for this ecu? i have shay eec-v ecu, VS&F-12A650-AKB.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.