nissan primera 2002 Immo

[HITECH]

Nissan primera 2002 Immo car was right wheel and after steering was change to left wheel car can't start, attached is the picture of my immobilizer.I connected SBB and car asking for pin code to program.any help

SIEMENS

28590 C9965
MADE IN MEXICO


5WK4 8043


20474A


thanks in advance

[__nero__]

foto BCM and VIN

[HITECH]

what i posted is what? i have 2 images with the details below?where can i locate BCM and VIN?

[HITECH]

foto BCM and VIN
Please explain further,what is BCM what is VIN,I'm new in this business can you please direct me where to locate BCM and VIN?
thank you

[achaccha]

You need to publish the reading of the memory of the BCM. The BCM is a module that is a little more arriva of the accelerator pedal. changed as rudder may have changed their ubicacion.desarme the dashboard. regards

[HITECH]

Yes i understand,but where is the BCM located in the car?

[electrones]

Hi friend

BCM :
1-behind the glove box,
2-unscrew the upper 3 screws
3-unscrew the botton 2 screws
4-pull out the glove box
5- release latches and pull out the immo
good luck

But before that,look below to see if you have a larger box with three plugs, your box immobeliser and central locking.
post photo of this

[HITECH]

Hi friend

BCM :
1-behind the glove box,
2-unscrew the upper 3 screws
3-unscrew the botton 2 screws
4-pull out the glove box
5- release latches and pull out the immo
good luck

But before that,look below to see if you have a larger box with three plugs, your box immobeliser and central locking.
post photo of this

Thank you brother,can you get me example of some writings i may find on the immobilizer box?

[electrones]

Hi friend

Your BCM is a black box, see attached image, these are examples of bcn nissan take a careful look

[HITECH]

Hi friend

Your BCM is a black box, see attached image, these are examples of bcn nissan take a careful look


Ok have Black box immo with 3 socket,attached is the image,BCM black box

[achaccha]

Hello Friend tested the generic code 5523?
good luck

[HITECH]

Hello Friend tested the generic code 5523?
good luck

yes this codes was tested already but no luck friend

[HITECH]

Any other solution friends?

[HITECH]

When i read key with ZED-BULL below is the info

ID : A3EB4A14
MODE : LOCKED
CHIP : PCF7936

TYPE : 46 CRYPT PHILIPS

How to get pin code for this car please

[__nero__]

VIN number
SJN..............
?

[__nero__]

VIN isn't in BCM
VIN is an incipient number of the bodywork from SJN
he consists of 17 signs

[HITECH]

SJNBBAP12U0019429

THANK YOU

[__nero__]

PIN 2795 PIN

[HITECH]

Tested say invalid pin, any idea?

[bluedid]

the pin is 100% good check fuses-plugs and make a diagnosis and give the PXXXX (eg p1610 p1614...) codes you will found

[HITECH]

I get this code p1610 immobilizer and other code but i don't actually remember,but will go to car branch and get that too

[HITECH]

Fault codes

Vehicle: Nissan - Primera P12 [02-06] - 2002
P1612 - Immobilizer
P0113 - Intake air temperature sensor
P1610 - Immobilizer
Fuel/Ignition (QG18 - Engine - MT/AT)
DTC Description

If you erase fault codes P1612 will clear but other 2 code will never clear,I also find out immobilizer signal light on dashboard not powering,if immo connected or not connect the immobilize key sign on dashboard not show,always off,even if you try to start car immobilizer light never blink,always off

Hope with this info you can help me solve my problem
Note : i gave the BCM image to a friend he gave me the same code 2795

[__nero__]

on 99% the guilty is BCM - exchange BCM

[HITECH]

There is one things i have notice,if you connect immo to car this IC inside immo keep heating.
TLE
4269GM
0139

Any idea about this?

where is trasceiver ?

[bluedid]

P0113 air temperature sensor Intake air temperature sensor circuit high input an excessively high voltage from the sensor is sent to ECM.
and the other P1610 p1612 is immo problem.
wrong connection problem check plugs again , some can put in wrong position....

[HITECH]

P0113 air temperature sensor Intake air temperature sensor circuit high input an excessively high voltage from the sensor is sent to ECM.
and the other P1610 p1612 is immo problem.
wrong connection problem check plugs again , some can put in wrong position....


P0113 air temperature sensor Intake air temperature sensor circuit high input an excessively high voltage from the sensor is sent to ECM.?

1 : ECM or BCM which?

2 : and the other P1610 p1612 is immo problem.
wrong connection problem check plugs again , some can put in wrong position....

Which plugs do you suspect most? can you guess,may be i can explain further to my technician.

[HITECH]

I'm sorry to delay the reply of this post,After fixing new immobilizer,i manage to read the pin code of the new immobilizer,i used the sbb to program the car and car was able to start. thank you for the good support