View Full Version : BMW EWS3.2 problem
Sir Pommes
28th November, 2012, 08:23 PM
Hi,
i have a EWS from a 07/98 E39 520i here on my desk.
Somebody fiddled around with NCS Expert and set the EWS-mode from 3.2 to 3.3 and know the engine cannot start and no EWS-alignment can be carried out.
Can somebody please set the mode back to 3.2 so that i will work with a MS41.0.
regards
SP
clauberty
29th November, 2012, 01:41 AM
did you perform a diag ?
what dtc have on ews and ecu ?
alignment is possible to do from inpa /DIS
what error do you have when you try to do alignment
bram380
29th November, 2012, 02:29 AM
ews with rolling code reset:
Sir Pommes
29th November, 2012, 11:08 AM
ews with rolling code reset:
Hi,
and now its in EWS3.2 mode?
regards
Jan
Sir Pommes
30th November, 2012, 10:15 PM
ews with rolling code reset:
Hi,
unfortunately it does not work. Same as before.
The problem is not the key but the interface between EWS and DME. The communication in EWS3.2 mode is different to EWS3.3, i think you know. The MS41.0 only understand EWS2 and EWS3.2 protocoll. Now the mode is set to EWS3.3 and EWS alignment is not possible.
So i need to set the EWS back to EWS3.2 mode.
Does anybody have an EWS3-dump from a car with MS41.0 (E39, E38)?
i hope somebody can help.
regards
SP
bram380
1st December, 2012, 02:26 AM
please detailed ews part number you need.
Sir Pommes
1st December, 2012, 07:54 AM
please detailed ews part number you need.
Here are the details.
BMW part number 61 35 8 382 453
HW02 SW05
But this part number was used in EWS3.2 and in EWS3.3 cars too, so it will not help to look for a dump.
The dump must be from car a with MS41(6 cylinder) or M5.2 (8 cylinder)
regards
SP
bram380
2nd December, 2012, 04:23 PM
read flash from dme & post here.
Sir Pommes
2nd December, 2012, 04:37 PM
read flash from dme & post here.
The ISN is matching, thats not the problem. GT1 says something like "EWS and DME are not compatible" .
The last option is to remove immobilizer function from DME.
I that what you want to do?
regards
SP
bram380
2nd December, 2012, 05:32 PM
Hi,
i have a EWS from a 07/98 E39 520i here on my desk.
Somebody fiddled around with NCS Expert and set the EWS-mode from 3.2 to 3.3 and know the engine cannot start and no EWS-alignment can be carried out.
Can somebody please set the mode back to 3.2 so that i will work with a MS41.0.
regards
SP
ISN of DME-EWS not same.
ISN EWS is 0D77
ISN DME is 024B
http://www.digital-kaos.co.uk/forums/attachments/f178/159923d1354464857-bmw-dme-ms41-0-immo-off-ms41-5wk90322-528i-org.rar
Sir Pommes
2nd December, 2012, 05:51 PM
ISN of DME-EWS not same.
ISN EWS is 0D77
ISN DME is 024B
http://www.digital-kaos.co.uk/forums/attachments/f178/159923d1354464857-bmw-dme-ms41-0-immo-off-ms41-5wk90322-528i-org.rar
Thats not the file from the 520i. This file has nothing to do with this thread. I checked the ISN from the 520i DME via INPA and its also 0D77. Sorry for the confusion.;-)
regards
SP
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.