PDA

View Full Version : Siemens fenix 3


awautosport
30th July, 2014, 09:34 AM
Hello,


I have a Siemens Fenix ​​3 of a Clio 1.4 that I want to make immobilizer free. Now I read on the forum that mc68xxxxx had to get by on ff things out. Chip empty I have no ability to read, the chip can not I just solder the chip out? Who can help me.


Sorry for my bad english.


regards Alex
metercar
30th July, 2014, 11:08 AM
This file work
metercar
30th July, 2014, 11:27 AM
and connections...
awautosport
30th July, 2014, 05:31 PM
Thanks but i don't have a programmer to read the chip. there is another possibility to empty the chip? I meant if I would let out the chip that would not work? kind regards alex.
lolilocortachispas
30th July, 2014, 07:37 PM
you need program the file, xprog work for this

dont forget cut immo line

luck
awautosport
31st July, 2014, 07:20 AM
Hello the immo line is line 25 ?
Mr BLACK
31st July, 2014, 07:52 AM
no programmer no immo off ...try to buy upa or xprog
awautosport
31st July, 2014, 02:17 PM
Hi I have just ordered a xprog to read him out. However, the chip was not there, but I take the gamble between the chip in the ecu is a mc68hcpe11e1vfn this is the same as a hc11e9?
Zmann
31st July, 2014, 04:02 PM
Practically the same
honingkoning
3rd August, 2014, 06:14 PM
Hi I have just ordered a xprog to read him out. However, the chip was not there, but I take the gamble between the chip in the ecu is a mc68hcpe11e1vfn this is the same as a hc11e9?

You mean no CPU in ecu, buy new ecu from yunkyard.
If you want to read with xprog you need to remove mcu and put in adapter.

Wbr Adam.
awautosport
17th August, 2014, 10:09 PM
Who can tell me how i read with x prog the chip is mc68hcp11e1vfn
honingkoning
17th August, 2014, 10:19 PM
Who can tell me how i read with x prog the chip is mc68hcp11e1vfn

Like i Said, remove from board put in adapter and read.
Was my answer not good enough?
awautosport
18th August, 2014, 06:18 AM
Hello,


the mc68hcp11e1vfn (4E28B) is not in xprog. if I read only as a mc68hc11e9 (4E28B) I get him the error device timeout error is silent. I also tried an external 12v but will not help. what am I doing wrong?
honingkoning
18th August, 2014, 09:30 AM
Hello,


the mc68hcp11e1vfn (4E28B) is not in xprog. if I read only as a mc68hc11e9 (4E28B) I get him the error device timeout error is silent. I also tried an external 12v but will not help. what am I doing wrong?

Read as secured, this is the one under the 4E28B in xprog menu.

Should be ok.
awautosport
18th August, 2014, 03:53 PM
hello even that does not work which adapter should I use and what are the best settings oscilator?
awautosport
19th August, 2014, 03:31 PM
Can nobody help me ?
key4man
19th August, 2014, 05:27 PM
Hello my friend
Here you have another solution without complications:
- If you are able to start the vehicle, Then go to your ecu and cut pin 29
Immobilizer line for 1.4l ECU
(must be done with engine working)
This will remove the immo (But note that if you disconnect the battery immo will return)


- If the car is not starting at all, what needs to be done is to open the key, and read from the board a numbers that you need to send to me and I will turn this numbers to pin code which can be
start the vehicle Using the button lock/unlock.

Good luck