59F decoder tool open project with hex files

[Syria777x]

include hex,diagrams + softwares :elefant:
thanks + rep > = pass : otocheck :02.47-tranquillity:

https://mega.co.nz/#!D4ZU1BqK!Mr6fnDIDM7YkPNPmtQbCXKzb0Ell9k7nZSylvOl SZf8



Please pass

Thanks


Sent from my iPhone using Tapatalk

[danyguit2000]

Hi mates,
Can anyone share the HEX file to this project please, as all links are dead...

Thanks in advance
Please, anyone?

[cp2010]

please here...

[motorbike59]

hi mikroel I need device tell me the price

[XJTAG]

[DEVIS = cp2010; 3476569] s'il vous plaît ici ... [/ DEVIS]


thanks cp2010 your diagram is good, see my pcb i delate 7805 ici and change the relay bye two 12v, is not comply becaue i no find ftdi232 and lm339 ,

for "les dz" can you cal me for this pcb

[XJTAG]

[DEVIS = cp2010; 3476569] s'il vous plaît ici ... [/ DEVIS]

on pdf file , the pic16f876a work good for me tested and 100% work , i change only the fuse code on microchip mplab software

i change lm339d by lm2901d i find it on ecu renault dci 1.5

[mikroel]

This is my version .

Can be used 5VDC or 12VDC relays
Also 5V DC to220 or soic8 voltage regulator

https://uploads.tapatalk-cdn.com/20190130/cb1fd83beccc495723ca7194ec805b41.jpg


Sent from my iPhone using Tapatalk

[giary74]

hello @giary74

the PIC16f876A work for me , the PIC16f876 and PIC16f876A is same but only the bits setings no same

hi xjtag,
I went crazy trying to program PIC 16f876A and not A.
I also bought PICKIT 3 without success ...
For now I have other problems to solve, but this fall I want to try again.
Could you advise me on the right settings? Thank you

[amor89]

hi need to program ftdi ft232rl need help with mprog3.5 it tells me no devices found and when I go see in my pilot I see the signature mr-elettronica-59f-marelli-tuning
Thanks for your help

[kendtamas]

Hi,

I`m make decoder.
Use connect ecu click DATI botton ok.
Read (click LETTURA) ecu correct (IAW59F HW003), and save file.
click IMMO OFF, programme eeprom no error, diagnostic read ecu live data, ecu programmed and lock, dont start possible.
click RIVERGINA, programme eeprom no error, diagnostic read ecu live data, ecu dont relarn state.
click APRI FILE, open file and click PROG, wait ecu connect error message TIME OUT.

see pic.
What is problem?

Read dk arhive.
Write post HW<100 immo off not possible inside MOTOROLA CPU.
HW>100 immo off possible inside ST CPU.
Realy?

This post realy, HW<100 immo off and write ecu flash and eeprom possible other tools?
HW003 write only BDM? (HW<100)

http://www.digital-kaos.co.uk/forums/archive/index.php/t-374440.html


637145637146


Experiences (time out problem) :
Power connection is correct or incorrect.
Incorrect connection board to ecu, change 15 and 30 dot.

BOARD to ECU
pin1 to pin16 (K-line)
pin2 to pin4 (30_+12V)
pin3 to pin17 (15_+12V)
pin4 to pin10 or 34 (31_ground)

ECU differents works software possibility state.
1. ECU coded.
2. ECU virgine (immo code necessary and auto relearn first ingition on! correct immo module works necessary)
3. ECU virgine and immo off (immo code no necessary, but to get immo code automatic relearn!)
4. ECU virgine and immo off and automatic reactivation coded state (same ECU) EEPROM lock necessary, which is difficult to solve.

637462

ECU software change.
For HW303 I tried, it worked there.
If the content is not good, the controller will not restart at the end of the programming and bring the programming to a bad state.
This was the wrong source for me.
The result of the reading is not always successful, but the program does not indicate an error while reading.

637460637461

[Panathaole]

Hi

Do you know we're I can buy a good PCB board , to build the decoder?

[kendtamas]

Yes of course.
Please send PM personal information (name, addresse, phone number and send to you)

637465

[kendtamas]

Have you experienced an ECU reading restart while reading?
Any other bug?
Or, in each case, it reads and writes for the first time, changing state (virgin/immo off).
Other people's experience would be interested in the device.

Why do you need a switch, does anyone know this?
User manual?
Don't anyone know about the issues below?

[mikroel]

https://youtu.be/tmvmvd0HwLo

Sent from my HONOR 8X

[kendtamas]

Ducati ECU reactivating coded.
Later make a video.
Not fix virgin and immo off state :(

Change ECU software? this HW002? ducati ecu.

Power OFF-wait-ON, read state ... ECU coded (ducati)

[crisgsm]

Hi
can someone share original software frome first post?
Thank you!

[crisgsm]

Hi
can someone share original software frome first post?
Thank you!

no one?
please i still needed!

[XJTAG]

[QUOTE = giary74; 3627094] hi xjtag,
I went crazy trying to program PIC 16f876A and not A.
I also bought PICKIT 3 without success ...
For now I have other problems to solve, but this fall I want to try again.
Could you advise me on the right settings? Thank you [/ DEVIS]

hello

@giary74

sorry for this delay , here good file for PIC16F876A without passeword good luck friend

[XJTAG]

hello

need help for this problem , the driver is good installed but "hw:????" no detected

thank you in advane

[crisgsm]

hello

need help for this problem , the driver is good installed but "hw:????" no detected

thank you in advane

check pic ! something is wrong there i think!
you can try first give power to box then conect usb!

[crisgsm]

hello

need help for this problem , the driver is good installed but "hw:????" no detected

thank you in advane

can you share exe please! i need archive with soft!
thank you !

[araby80]

Hello all,

I had made pcb and working good for 59f ecus but it dose not work on fait grand punto with 5SF ecus,

Dose and body had tried to read it with this project?

Thanks

Sent from my AGS-L09 using Tapatalk

[dalisman]

did any one have driver for 64bit ?

[motorbike59]

ciao ho lo stesso problema che hai risolto?

[mikroel]

drivere 32 bits and 64 bits
Thank and rep for pass

[motorbike59]

hi vlada, you posted the drivers 32/64 bit 59f rar you can send me password please thank you in advance.

[Ducabrem]

[QUOTE = mikroel; 3823835] drivere 32 bits y 64 bits
Gracias y representante por pasar [/ QUOTE]
Could you tell me password?
Thanks

[badyl00]

There is no answer about password to driver archive from mikroel. I mod myself original driver for x86 and x64 to get them work on windows 7 and above. Tested 100% working, no password. If not check driver properties in control panel and uncheck "load VCP".

If post helped please thank and rep.

If someone need i have project of PCB (1 layer) with DIP version of microprocessor, just write.

[Dacha]

Hi badyl00

Please send me
(https://www.digital-kaos.co.uk/forums/member.php/130537-badyl00)project of PCB (1 layer) with DIP version of microprocessor and other details for iaw59 decoder.

I thank in advance!

[viktor64]

Hi badyl00
Please send me project of PCB (1 layer) with DIP version of microprocessor and other details for iaw59 decoder.


I thank in advance!

[badyl00]

Here is my project. Use files in thread to program device. Press thank + rep, for pass write PM.

[GHAZI19]

s'il vous plaît passer
Merci

[ruicosta]

when I try to program the pic 16F876A with labtool I received this message, once the programming is finished when I compare the two file written and read I find it different that someone can help me please783500783503

[Panathaole]

What is the point to make all this?
It works better than fvdi?

[ruicosta]

rapport qualité / prix est meilleur
le rapport qualité / prix
Meilleurprice / quality ratio is better

[danizichi]

Hi! I am becoming crazy.
I builded my Decoder, but it not works.
The connection with the pc is okay.
I wire the ecu ad try to read it, but when sw try to read, after many seconds, I get an error. How I can solve it?
I checked the pcb, I make an second decoder but same error.. tried 3 ecu


https://youtu.be/LrDJBwB4nTY?list=WL

[oui]

There is no answer about password to driver archive from mikroel. I mod myself original driver for x86 and x64 to get them work on windows 7 and above. Tested 100% working, no password. If not check driver properties in control panel and uncheck "load VCP".

If post helped please thank and rep.

If someone need i have project of PCB (1 layer) with DIP version of microprocessor, just write.


hi friend

please send me the project of pcb singel layer with dip versionof microprocessor

tankyou in advanced

[oui]

[QUOTE = caliskan71; 2514080] inclure hexadécimal, diagrammes + logiciels :elefant:
merci + rep> = pass: otocheck :02.47-tranquillity:

https://mega.co.nz/#!D4ZU1BqK!Mr6fnDIDM7YkPNPmtQbCXKzb0Ell9k7nZSylvOl SZf8 [/ QUOTE]



please renew the link

[coisasgaragem]

anyone can share the link please?

[PaoloDigital]

Hello Friends.Need Software FIXED all bugs with iaw hw<100 IAW 59F Decoder V5.5 HW3 - Magneti Marelli , M.Tuning , search software v5.5
version with
fixed bug to work on 59f under hardware hw :100 002 , 023 , ecc.. <100.

Please one to post this version software 5,5 for hardware 3 with fixed bug under <100.thanks

[oui]

Please i nedd the PCB (1 layer) with DIP version of microprocessor

[mimielk]

Please renew the link.

[mimielk]

I pressed thank + rep but I didn't get the password.

[Friki86]

Someone send me the file for the realization of the iaw decoder for iaw 59f,
Please.

[pricardof]

link off, please renew

[Friki86]

would you give me an active link where I can download the files, please.

[Friki86]

I need the project for Reading iaw 59 f, please

[iotato]

ciao a tutti l'antivirus mi ha corrotto i file se qualcuno puo ripostarli grazie infinite

[axigenc]

bu ecu nasıl yapılır biri bana yardım etsin

[axigenc]

please someone help me how to make this ecu

[eric paris]

hello,

look if it's ok for you

https://mega.nz/file/9tZlzSDQ#qhyDifhmU0QW97wZWRC5K64jWxIXemtjBwCHeaJYk QU

[rikardo1]

Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very muchHi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very muchHi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much
Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

[rikardo1]

Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much
Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

[rikardo1]

Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much
Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very muchHi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

[rikardo1]

Hi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

errHi everyone, I have the same problem, I bought one and made another, the program doesn't recognize the programmer, it came programmed i 0403 1967, I don't have a hw in the software and it doesn't recognize the programmer, besides, the file it gives doesn't even belong to ft232rl, I would like some help and if someone in forum has the programmer working thank you all very much

[rikardo1]

Hello, I made the Marelli decoder programmer for version 5.5, it seems not functional, I programmed the FT232FL with an otocheck file, it appears nagneti Marelli, I installed the drivers for Win7, FTDI, it seems to be ok, I don't know, I did the programming wrong, so when I turn on the programmer, it doesn't light up the version 5.5 buttons or The relays will be the micro not ok I wish you could help me in advance thank you very much
Hello, I made the Marelli decoder programmer for version 5.5, it seems not functional, I programmed the FT232FL with an otocheck file, it appears nagneti Marelli, I installed the drivers for Win7, FTDI, it seems to be ok, I don't know, I did the programming wrong, so when I turn on the programmer, it doesn't light up the version 5.5 buttons or The relays will be the micro not ok I wish you could help me in advance thank you very much

[rikardo1]

Hi, I already built the decoder but it doesn't work, possibly the program in the pic must not be good, someone who built the programmer and it's working, I programmed everything with Delmemt, who was the person who uploaded the circuit and the program doesn't work, I have the original ft232 I was able to program it and now I have a Marelli magneti but the programmer doesn't communicate with the software my father bought one that is the same as the one I built if there is anyone with a working programmer who can help I would be very grateful, thank you very much

[rikardo1]

Hello everyone, has anyone built a programmer that is working, my father bought one from cartools and it works well, I took advantage of it and read the ft232 with mprog and it has id0403, id 1967, and it works like that, I think, and the project doesn't work, if anyone wants to help, I think The problem must be in the hexadecimal of pic16f876, meaning the programming doesn't work
thank you all

[eric paris]

hello, I'm not going to help you much,
I made this circuit a long time ago with classic components on a bread board and it wasn't very stable in operation,
I have to redo it in cms but I didn't have didn't take the time