PDA

View Full Version : easytronic opel corsa c



rafal
6th April, 2017, 07:51 PM
hi all.
I have problem with gearbox easytronic MTAF13 corsa C engine Z10XE.
Fault codes: P1710 , P1711 , P1712
I have done:
1) new clutch set
2) all procedures by op-com
F on dashboard is flashing only on 4th and 5th gear.

tomo776
9th April, 2017, 09:47 PM
Maybe you have corrupted 24C16 in easytronic.
You can try to write this file change vin with op com and try.

441909

Regards

Brolk
9th April, 2017, 09:52 PM
hi

P1710-ERROR DE VELOCIDAD DE RUEDA
P1711-NO SIGNAL F / L
P1712-NO SIGNAL F / R

Brolk..

vladanr
10th April, 2017, 10:47 AM
In relay/fusebox in engine compartment you have two modules (like bigger relay ) it is converters foe right and left wheels speed.check them and clean wheels ring where speed sensors reading ,thats is your problem.

rafal
11th April, 2017, 10:27 AM
thank you for replay.
these corsa is with abs so in fusebox i have empty spaces for relays

adiagnostyka
11th April, 2017, 06:35 PM
When i have simular problem with easytronic in corsa c i have problem with bigger motor on gear selector. Brash replace solve my problem

rafal
11th April, 2017, 07:21 PM
i will check tomorrow

cd345
2nd February, 2018, 08:37 AM
Hello,

i hAve the same Problem with P1711, 1712, 1710.
no comiunication with from ESP 8.0 to MTA. The sensors work for ESP 8.0 but not for MTA
MTA works in 2 gear. F in Display. car starts and drive only in 1 and 2 gear.

i have OP com. How can i conekt the snsors to ESP?

Regards

Markus

mikeanthony
29th May, 2018, 12:55 PM
i have exactly the same issues

d.zio
17th June, 2018, 08:47 PM
hello
any solution these codes?
corsa c z13dt
car doesnt start N flashes and when i attempt to start F flahes
faults p1710 p1711 p1712
sensors work ok to wheels
abs communication ok
engine fault SVS from auto trans required

any help appreciated

sergei5005
14th February, 2020, 09:54 PM
Hello . someone find solution for P1710-P1711-P1712 . Tree codes appear simultaneously and with or without moving. Any help please ???? The car is one Corsa C 1.8 with Easytronic gearbox and ABS .
THANKSSS !!!!!!

rafal
14th February, 2020, 10:35 PM
Hello . someone find solution for P1710-P1711-P1712 . Tree codes appear simultaneously and with or without moving. Any help please ???? The car is one Corsa C 1.8 with Easytronic gearbox and ABS .
THANKSSS !!!!!!

I solved problem by new motors of gears

sergei5005
14th February, 2020, 10:46 PM
Thank you for you reply. Im have this problem with the car in moving or without moving. And fails appear simultaneusly. THANKSSS !!!

sergei5005
24th March, 2020, 12:18 PM
Hi friend. "I solved problem by new motors of gears"
You make reference an the 2 motors in gearbox(robot) or Easytronic module with clutch actuator motor ???
Im have this problem now.
Ignition swicht is turn ON ever N is flasher. With ignition swicht is ON the scan tool (OP-com and other scan is same results) not response from easytronic diagnostic. But push brake and inmediatly scan tool show diagnostic,ever P1710-P1711-P1712. Sound like as before push brake the easytonic not found and not receive data bus from ABS module. After push brake easytronic response. For start car ever need push the brake before ignition swicht turn ON.So N in display flashing 3 time and next N is permanent. Tha car start. First turn ON ignition swicht and after push brake ever show F in display and the car not star.Strange fail. Any experience??? THANKSSS!!!!!!

rafal
24th March, 2020, 12:31 PM
https://workshop-manuals.com/vauxhall/corsa-c/k__clutch_and_transmission/manual_transmission_front_wheel_drive/manual_transmission_f_10/f_13/f_15/f_17_easytronic_f_13/f_17/m_20/other_information/required_commissioning_routines_for_the_easytronic _system_for_service/repair_work/

read all here.................no comm - number 5 of manual

Andr33iy98
10th September, 2020, 12:13 PM
Easytronic module with clutch actuator motor you means this by new motors of gears ?

Andr33iy98
10th September, 2020, 02:10 PM
How you guys resolved this ? I have the same dtcs

rafal
10th September, 2020, 03:43 PM
i solved when i mounted new gears motors..............

Andr33iy98
10th September, 2020, 04:14 PM
You post the code of the products ? Or something like a pictures, a location, it is hard to repair it? I hear that you can just replace the brushes and you are good to go. I am not sure.
Any help will be good
Thanks

Andr33iy98
11th September, 2020, 09:43 AM
New gear motors can you give me a code about this product ? They are expensive ? Need programming after replacement ?

Andr33iy98
19th September, 2020, 08:50 PM
hi all.
I have problem with gearbox easytronic MTAF13 corsa C engine Z10XE.
Fault codes: P1710 , P1711 , P1712
I have done:
1) new clutch set
2) all procedures by op-com
F on dashboard is flashing only on 4th and 5th gear.


On vauxcom I read 107 km/h when I am full-stopped, AT input/output speed(automatic transmission) and also Front left/right wheel sensor is showing 0 rpm, all of them.
Coud be cranckshaft position sensor ? No error related to this sensor but I read that this is the one responsable to this anomaly of changing gears.
IF it is CPS how to test it with a multimeter ? It has 3 pins.