VW PASSAT '13 immo info MED17.5.6 07906055CR

[dd1]

HI everyone, i have a 2013 vw passat, with MED17.5.6 and i need to get the immo info, CS pin mac. i read the eep and posting it here. someone has changed the cluster and now the car wont start. i am new to this kind of issue. what needs to be done start this car?? thank you in advance.

[dd1]

anyone??????

[DOUGLASDL]

friend posted image of ECU and EPROM and micro

[DOUGLASDL]

file micro y eprom

[dd1]

thank you, here are the files

[dd1]

just to mention, the cluster was changed on this car. what is the correct way of fixing the issue. i cant access the MED17.5.6 for mac cs pin. if you have a good procedure to adapt the cluster to this car. someone has done a work on the cluster. it wont show the immo issue in the cluster. but the engine control module has a key blocked. thank in advance

[DOUGLASDL]

eprom reading is not good

[dtip]

is it USA passat ? B6/B7 is with immo in CCM not in cluster. Maybe if US version, if not then you have other problem

[dd1]

even the one above also not good??? i have 2 eeps here. one is from the beginning

[dd1]

yes, it is a USA.

[dd1]

is it USA passat ? B6/B7 is with immo in CCM not in cluster. Maybe if US version, if not then you have other problem

That is strange. this is what happened. before i got the car, they had swapped the cluster, since it had some issues. now, someone had swapped the eep on that cluster. and the cluster wont show the immobilizer displayed on the display. they have 5 clusters on hand. they mixed them up. how can i know which one is the original?

[dd1]

C an anyone help me here please?

[DOUGLASDL]

file off post result

[dd1]

thank you so much for your help. your file worked like a charm. can i ask you favor? someone helped me with the another vw jetta, it is a me7.5, i did an engine control module swap, the DK member helped me with the IMMO issue, but now i have the p0606 fault code and p0030 also, this code was there before, so i want do a DTC REMOVE. can you help me with this? thank you in advance

[DOUGLASDL]

[QUOTE = dd1; 3507168] muito obrigado pela sua ajuda. seu arquivo funcionou como um encanto. Posso lhe pedir um favor? alguém me ajudou com o outro vw jetta, é um me7.5, eu fiz um swap de módulo de controle do motor, o membro DK me ajudou com o problema IMMO, mas agora eu tenho o código de falha p0606 e p0030 também, esse código estava lá antes, então eu quero fazer um DTC REMOVE. Você pode me ajudar com isto? agradeço antecipadamente [/ QUOTE]


Yes friend sends a picture of the ecu and the original files

[dd1]

ok, you need the micro or eep or both????? remember i dont have the original ME, it has been swapped, the car starts ok but i have those 2 codes. CHECK ENGIE is on. i want them deleted. guide me friend..............

[DOUGLASDL]

[QUOTE = dd1; 3507187] ok, você precisa do micro ou eep ou ambos ????? lembre-se que eu não tenho o original ME, ele foi trocado, o carro começa ok, mas eu tenho esses 2 códigos. CHECK ENGIE está ativado. Eu quero que eles sejam apagados. guie-me amigo .............. [/ QUOTE]


reading micro and EPROM and confirms ECU image

[dd1]

hi, here are both

[dd1]

photo of the ecu

[nokwueze]

here is your file

[dd1]

hi and thank you NOKWUEZE, my issue is the fault codes, the car starts, someone had already immo it off for me. the only problem was that i had 2 fault codes in the engine control module. i needed DTC REMOVE. sorry about this brother

[DOUGLASDL]

record this file friend

[dd1]

hi, now is this the eeprom or micro??? sorry i am new to this. thank you

[DOUGLASDL]

micro file

[dd1]

[QUOTE = dd1; 3507168] muito obrigado pela sua ajuda. seu arquivo funcionou como um encanto. Posso lhe pedir um favor? alguém me ajudou com o outro vw jetta, é um me7.5, eu fiz um swap de módulo de controle do motor, o membro DK me ajudou com o problema IMMO, mas agora eu tenho o código de falha p0606 e p0030 também, esse código estava lá antes, então eu quero fazer um DTC REMOVE. Você pode me ajudar com isto? agradeço antecipadamente [/ QUOTE]


Yes friend sends a picture of the ecu and the original files

now the only thing i am stuck with is that the ABS / TRACTION light blinking on the cluster, fault code is for coding error. this happened right after cluster swapping took place. Since i have repaired the original cluster, i wonder why is it giving the error code? can you guys help me out with this issue???? the long coding is all 000000000000000. thank you in advance

[DOUGLASDL]

friend the error code disappeared with my edit in file

[dd1]

friend the error code disappeared with my edit in file

The abs fault code says "abs not coded" and the long coding is all 000000000000000000000. I need to recode the abs.

[DOUGLASDL]

LONG CODING

[dd1]

No, it is not your problem. Somehow the abs loses the long coding if you try another cluster. But I have repaired the original cluster now and need to decide abs also