bmw E46 immo off 0261208539 and ews 4.3

[vageric]

is it possible to make this ecu immo off?
car is BMW E46 2004
DME 7 541 461
Bosch 0261208539
ews 4.3 (attach dump ews)

car crank but not start

have checked fuses under hood and all is oke!
dtc is ews/dme datastream

isn in ews is A9 64 if im correct!

or maybe can check if ews dump is oke?

[Stelaras26]

vin : WBAEY71060FT11075

isn is indeed A9 64

203121 kms

Upload the ecu file too ;)to check mate :D

[vageric]

i dont see any eprom inside ecu!
you know what eprom is inside?

[Lambda1]

Swap out board and there are mpc, flash... or read via bdm pads.
Post flash.

[Stelaras26]

Its MEV9.2

MPC564 & ext. flash M58BW016

[vageric]

gonna read the flash and get back at your guys.

[vageric]

oke have added reading ecu in post #1

[Lambda1]

okay and what you want? Immo off?
Isnt possible via file or not released free offical.

[vageric]

okay and what you want? Immo off?
Isnt possible via file or not released free offical.

immo off if possible!
otherwise if possible to match ews and ecu so car can start!
im willing to pay for immo off if needed.

[Stelaras26]

Ecu and ews have the same vin same isn.

[adiagnostyka]

Did you try just resynch by inpa launch fvdi or some other tool ??
Like Stelaras26 (https://www.digital-kaos.co.uk/forums/member.php/540356-Stelaras26) said vin and isn are equal in ews and dme. I think synch via obd and drive.

[doctore]

with used ews 3 you will solved problem:)

[vageric]

Did you try just resynch by inpa launch fvdi or some other tool ??
Like Stelaras26 (https://www.digital-kaos.co.uk/forums/member.php/540356-Stelaras26) said vin and isn are equal in ews and dme. I think synch via obd and drive.

yes, i tryed to sync ews and dme but not possible.
i have try with inpa and avdi original and lunch but all failed.
is it possible to sync them outsite the car? on the bench?

is it otherwise possible to make immo off with emu?

[vageric]

is it possible to sync ews and dme trough dump?
if so can someone do it for me?
for testing before go further

[kiszka]

is it possible to sync ews and dme trough dump?
if so can someone do it for me?
for testing before go further
no, it remains only to do ews 3

[Stelaras26]

This dtc is in ews or in ecu??
Check also crankshaft sensor if it reads rpm.
And fuel pump ;)
Just To be sure.

[vageric]

This dtc is in ews or in ecu??
Check also crankshaft sensor if it reads rpm.
And fuel pump ;)
Just To be sure.

have change ews 4.3 with ews3 today and make key but same problem.
car crank but no start. and cant sync ews with dme. i tried today ews3 sync with dme with lunch and get ews not match dme.
if i read ews i get no dtc.
read dme get 2 errors.
2F45 dme: ews data stream
2E95 dme: aternator
by clear dtc, 2E95 get cleared but come back after ignation on/off.

crankshaft sensor been allready replaced.
feul pomp is ok.

[kiszka]

have change ews 4.3 with ews3 today and make key but same problem.
car crank but no start. and cant sync ews with dme. i tried today ews3 sync with dme with lunch and get ews not match dme.
if i read ews i get no dtc.
read dme get 2 errors.
2F45 dme: ews data stream
2E95 dme: aternator
by clear dtc, 2E95 get cleared but come back after ignation on/off.

crankshaft sensor been allready replaced.
feul pomp is ok.
share read eeprom ews

[vageric]

share read eeprom ews

see post #1

[kiszka]

see post #1

eeprom from ews3

[vageric]

eeprom from ews3

added on post #1.
only thing is this is dump is manual gearbox and car is automatic. (dont know if that is a problem)?

[kiszka]

added on post #1.
only thing is this is dump is manual gearbox and car is automatic. (dont know if that is a problem)?
use original keys, do re-synchro
ews and dme
give me a report what and as is
if all is ok press buttons
https://mega.nz/#!xqYkRC5B

[vageric]

use original keys, do re-synchro
ews and dme
give me a report what and as is
if all is ok press buttons
https://mega.nz/#!xqYkRC5B

just went to try your mod file and same problem.
i cant sync ews/dme.
with lunch it give me ews/dme do not fit toghter.
with avdi original it give sync not possible.
car cranck but not start.

[rm23]

did you sort the problem out ?

[kiszka]

just went to try your mod file and same problem.
i cant sync ews/dme.
with lunch it give me ews/dme do not fit toghter.
with avdi original it give sync not possible.
car cranck but not start.
my file is good
problem is that VVDI can't handle bmw, confirmed

[rm23]

I have same problem and same faults in ecu, can't do synchro , original avdi not possible, launch no, pa soft shows after synchro ok but car not start, faults remain ;( any idea? that just happened after flat battery.... is it immo off possible in that ecu ? MEV9.2

[vageric]

Hello, i did not solved the problem.
because client came and sold the car as it is.