Renault Kangoo UCH N2-x76 clone

[JFR-Tuning]

I read herre that posible only change the EEPROM 93C66 to start the Car. But ...

i have the damage ECU ( only Turn light are always blinks) and secocond scrapt ECU N2x76 but Hardware H V5 are little bit other. Second Hand is HV4.7

if i copy the eeprom Car wound Start and After i read the eeprom Alain it shows other dump i have prog and Check.

how is ist posible to clone this UCH. MUST I CHANGE THE MCU?

thnx for help
and all members here stay healthy

[cristinuz]

Swap eeprom,it should work

[JFR-Tuning]

no i do this serval times after that the immo not flash not light on. if i read it again after used first time the dump are not the same i programmed

[Bllinda]

Upload bcm h5w, h4.7w and the file that was in the car

[JFR-Tuning]

Orginal UCG

is
UCH-N2-X76
D V4.61
EEPROM 93C66

second Hand
UCH-N2-X76
H V5.0
EEprom is 93C66

von all i write org Dump in advance als a Dump after Replace the second Hand and read again after conect to the car

[Briankotze]

I have changed this uch many times by just changing eeprom over or copy eeprom data. You either have corrupted eeprom or something else is wrong. Use renault pin extractor , read ori eeprom and extract pin. Then try to program new key to car. You must also just configure uch by telling it what options it has if uch is not from exact same module. Also leave ignition on for 10 mins after eeprom change, switch off and on again. If you here fuel pump running light will be out

[JFR-Tuning]

I have changed this uch many times by just changing eeprom over or copy eeprom data. You either have corrupted eeprom or something else is wrong. Use renault pin extractor , read ori eeprom and extract pin. Then try to program new key to car. You must also just configure uch by telling it what options it has if uch is not from exact same module. Also leave ignition on for 10 mins after eeprom change, switch off and on again. If you here fuel pump running light will be out

yes that’s is the same I do before Aldo some times. In this case it not works only change eeprom. I have 2 second hand UCH and not work. Both do the same with the dum in eeprom. Do you make the change eeprom by kangoo 1,5 DCI ?

i will now make it Verhindern and reprogramm it with pin. I have the pin read by Avdi.

first I test it by 10 min ing on. That I don’t do this.

i will report. All idea are welcome

thnx

[Bllinda]

It is poorly scanned


Orginal UCG

is
UCH-N2-X76
D V4.61
EEPROM 93C66

second Hand
UCH-N2-X76
H V5.0
EEprom is 93C66

von all i write org Dump in advance als a Dump after Replace the second Hand and read again after conect to the car



https://www.digital-kaos.co.uk/forums/images/styles/DarkCore/attach/rar.gif 2. Hand after replace.rar (https://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=701450&d=1584959647) (280 Bytes, 1 views)

[JFR-Tuning]

It is poorly scanned

soory m8 in your cases I have no option to help y ... sorry

[Bllinda]

It is poorly scanned

Your Damp is corrupt


soory m8 in your cases I have no option to help y ... sorry

[JFR-Tuning]

Your Damp is corrupt

please tell me wich dump. there are 3
1. original car starts and run
2. second hand UCH origninal befote copy the org Dump
3. Second hand after prog the org Dump into second hand and make ing on in the car. Than i read it again because car not start also after 10 min ing on

[JFR-Tuning]

must read 93c66 inb 8 bit or 16 bit mode

[Bllinda]

Try .... ....

[JFR-Tuning]

Try .... ....
?
what you mean with

[Bllinda]

Read.mw.c66x8.x16