OP-COM SOFTWARE REQUEST

[fantomel]

As you know some time ago i asked for some help and you can see the result in my last post :
https://www.digital-kaos.co.uk/forums/showthread.php/821612-OP-COM-SOFTWARE-REQUEST?p=4058794&viewfull=1#post4058794

Ok, you will wonder why i ask for these installers :)

I plan a little surprise and i would love my surprise to be .... as complete as possible, so because of this i ask for a little support meaningOP-COM or VAUX-COM installed or installer kits Professional or Advanced that are from 2012 UP only English and are not in the list bellow.

Version Firmware Type
131223c_EN 1.59 Professional
131223e_EN 1.60 Advanced
141204d_EN 1.63 Professional
150406d_EN 1.64 Professional
170330a_EN 1.65 Professional
170823c_EN 1.66 Professional
181022a_EN 1.67 Professional



I know for a fact that there are also other versions then these as for example Advanced 161001a, so i am asking for your help ( you can write here or on PM)

[fantomel]

Since yesterday my list of versions that i have is like this:


OP-COM Version Firmware Type


110530a EN 1.44 Advanced
120309c EN 1.45 Professional
121231i EN 1.47 Professional
131223c EN 1.59 Professional
131223e EN 1.60 Advanced
141204d EN 1.63 Professional
150406b EN 1.64 Professional
150406d EN 1.64 Professional
170330a EN 1.65 Professional
170823c EN 1.66 Professional
181022a EN 1.67 Professional


I will take also kits or installed versions from non genuine interfaces that are not in the list and also just in English language.


If someone has Advanced versions newer then 2013 in English please do share :)

[mtechno]

I have op com 2014 but inside folder it has vag com these are instructions with it perhaps you recognize it?
primero instalamos el programa


conectamos el op-com al ordenador para instalar los drivers


abrimos el OCflash y actualizamos el op-com con el firmware 1.59


y por lo ultimo abrimos el software vaux-com (es la version 2012 ...pero esta modificado (actualizado) para 2014)


solo funciona con la version B ( todos los op-com clones China son la version B) agunos modulo mas modernos como immo de la astra J y otros mas de poca importancia FUNCCIONAN solo con la version C y D que de momento no existen como clones


MUY importante..antes de actualizar el op-com es necesario saber que version tenemos asi que abrimos las carcasa del op-com y en la placa base
tiene que estar escrito la V5 si pone V6 no se puede actualizar(es nesesario hacer algunas modificaciones (La V6 mejor no actualizarla sin hacer antes los cambios ...se puede bloquear)

[batrst]

181022a EN 1.67 Professional last one . have a opcom obd v2 tying to find drivers for it an cud it be up dated to work on last version

[Pofi87]

Can i have the 1.67 version please ? Or any what has a Gm Cruze 2.0 diesel in it . Thanks

[Mario6]

Can i have the 1.67 version please ? Or any what has a Gm Cruze 2.0 diesel in it . Thanks

If you have a regular Opcom China clone with FW minimum 1.45 use Vaux Com 120903a. There from 2010 to 2012 is the Chevrolet Cruze engine diagnostics.
2010y-Z20S1
2011y-Z20S1, Z20D1,
2012y-Z20D1.
There is no Chevrolet Cruze diagnostic option on Opcom 170823c FW 1.66. I do not know if 181022a FW 1.67 has the Cruze diagnostic option.

[Pofi87]

Hi. Tried that version (120903a) has cruze in it just its missing that engine file what i need...727161 Can someone give me a good version .Thanks

[Mario6]

Try this version fake Vaux Com 120903a plus 160115a Langdata.

[Pofi87]

Thanks , seems to be good for my job , will have the cruze back on saturday , hopefully now not for time waisting. I will report after i tried on the car.

[Pofi87]

So yesterday tried it , connects to ecu but couldnt read live data parameters etc. Just 3 red lines where the data should be. Whit all year what has it , and every 2.0 diesel. I want to teach up a dpf pressure sensor , and do a regen . But no luck.. tried ( snapon modis ultra, lunch, tech2,multi ecu , opcom, what worked whit it it was a hella diag what done for first so atm sorted . Thanks for the help :D

[Mario6]

It can be like that. I once checked Opel Insignia 2.0 163Ps 2010y and there were also no DPF measuring blocks (- - -). In the near future I will be checking Chevrolet Cruze 2.0 163Ps with the help of Opcom 15EN, 16 Pl, Vaux Com 16EN (HQ clone). If you are interested, I will write if it correctly reads the measured value blocks of the engine and DPF.

EDIT:

I used Opcom 150406d on a Chevrolet Cruze 2012y 2.0 163PS. Only in the motor is it possible to read blocks of measured values and programming. In Other calculators, you can only read and delete error codes.

[maktub]

Can somebody share 181022a_EN 1.67 Professional please? Thanks

[Mario6]

Can somebody share 181022a_EN 1.67 Professional please? Thanks

Here you go.

https://www.digital-kaos.co.uk/forums/showthread.php/700255-Opcom-2018/page6?highlight=opcom

[fogducker]

Can someone share 150406d_EN 1.64 please?

[Mario6]

Can someone share 150406d_EN 1.64 please?

Here you go. SW for HQ Clone.

pass bukiet

[fogducker]

Anyone got any idea why measuring blocks in
170823c_EN 1.66 Professional are empty for Vivaro B 1.6 diesel?

[Mario6]

[QUOTE=fogducker;3993445]Anyone got any idea why measuring blocks in
170823c_EN 1.66 Professional are empty for Vivaro B 1.6 diesel?

Maybe because it's a Renault engine. In Opel Vivaro I (1.9 d) I also didn't see measured value blocks (---) But I don't remember which SW OPCOM I used.

[fantomel]

https://iili.io/fToxkB.md.jpg

If you are curious open and see and you will not be sorry :) I always keep my word.

And a little bit of help to see if your inteface is good or not.

https://i.postimg.cc/dtpzJwXs/Check-FAKE-PIC.png

+ I added down PDF's for CH-CAN modification and also if you like printed boards the project for it.

Enjoy :)
Fantomel

[Mario6]

It works. I checked on Opcom HQ clone with PCB "Opcom New"
Thanks a lot.

[tazz75]

It works for me too...thx again ..you'r great ...

[western6089]

It is a functional solution. Thank you good work.

[alusta]

Hi! mario6. What is Rar pass OC 150406d EN?

[drz]

Works OK! Thanks again

[pepper]

Trying to get uptodate software to read corsa d 1.0 2014 any help?
Thanks

[pepper]

Here you go.
rar password please thanks

[tazz75]

rar password please thanks
Mr pepper 12 years 3 thx..no one thanked you. you ought be ashamed

[pepper]

Mr pepper 12 years 3 thx..no one thanked you. you ought be ashamed

3 years 1116 posts get a life

[bergbahn]

How to Modify Opcom Type B to Type C with CH-CAN Support? | OBDII365.com Official Blog (http://blog.obdii365.com/2020/07/11/modify-opcom-type-b-to-type-c-with-ch-can-support/)

[pepper]

Are the links still available they dont seem to be there?

[Mario6]

Are the links still available they dont seem to be there?

Links 2,3,4 work normally.

[alusta]

Hello.
I wonder for opcom cruze. Previously, 12093 v. I used. There is cruze in 2012, but not after. However, the astra j and cruze of 2013 are very similar. I also want to make some adjustments in this way. I wanted to try the 150406b version to see if there is anything different. But in the first installation, it changed the firmware version and made it 1.45. After that, activation was required. So I asked for help, if I can find the activation code I will continue. The FW update of the opcom plus device I bought from China can be done and V5.

[Mario6]

Hello.
I wonder for opcom cruze. Previously, 12093 v. I used. There is cruze in 2012, but not after. However, the astra j and cruze of 2013 are very similar. I also want to make some adjustments in this way. I wanted to try the 150406b version to see if there is anything different. But in the first installation, it changed the firmware version and made it 1.45. After that, activation was required. So I asked for help, if I can find the activation code I will continue. The FW update of the opcom plus device I bought from China can be done and V5.

Read post # 11.

https://www.digital-kaos.co.uk/forums/showthread.php/821612-OP-COM-SOFTWARE-REQUEST?highlight=opcom

[alusta]

Hi! Mario6. Compatible with 2013 model cruze-astra j. Have you tried in this direction? Because I'm curious, I want to tamper with it. Of course without breaking ...

[Mario6]

Hi! Mario6. Compatible with 2013 model cruze-astra j. Have you tried in this direction? Because I'm curious, I want to tamper with it. Of course without breaking ...

I was only doing diagnostics on my friend's Chevrolet Cruz 2012y 2.0D 163PS.(pictures) I don't have an Opel or a Chevrolet.

[pepper]

No all go to nothing:s:

https://anonfiles.com/n1i0W1E9pb/OP-COM_110530a_EN-Adv_v20830_Free4All_exe

[Mario6]

No all go to nothing:s:

https://anonfiles.com/n1i0W1E9pb/OP-COM_110530a_EN-Adv_v20830_Free4All_exe



Here you are. 3 FANTOMELS link still working.
Just check it carefully.
And have fun.

[alusta]

As you know some time ago i asked for some help and you can see the result in my last post :
https://www.digital-kaos.co.uk/forums/showthread.php/821612-OP-COM-SOFTWARE-REQUEST?p=4058794&viewfull=1#post4058794

Ok, you will wonder why i ask for these installers :)

I plan a little surprise and i would love my surprise to be .... as complete as possible, so because of this i ask for a little support meaningOP-COM or VAUX-COM installed or installer kits Professional or Advanced that are from 2012 UP only English and are not in the list bellow.

Version Firmware Type
131223c_EN 1.59 Professional
131223e_EN 1.60 Advanced
141204d_EN 1.63 Professional
150406d_EN 1.64 Professional
170330a_EN 1.65 Professional
170823c_EN 1.66 Professional
181022a_EN 1.67 Professional



I know for a fact that there are also other versions then these as for example Advanced 161001a, so i am asking for your help ( you can write here or on PM)


Hello Fantomel. I downloaded opcom 16.1001a and Installed it. System: windows 7 32 bit, 4 gb ram Amd processor. During the installation, a window popped up and it was installed automatically without allowing anything else. When I opened the program, it made the FW version from 1.45 to 165. I first entered the 2012 cruze part. There are a lot of options not seen in older versions. I haven't tied in the car yet. I'll try on the car when the weather conditions are right. I am pleased with this state. Thank you to those who contributed.

[pepper]

181022a has upgraded to 1.67 but isasking to activate?

[alusta]

181022a has upgraded to 1.67 but isasking to activate?

Good Morning. 161001a version does not require activation. Suitable for 2017 model vehicles

[leister]

Hi,

Does it really work?
Are these really a genuine professional and advanced versions?
Even professional version from 2020?
Does it work on v5 clone version?
Does it need activation?

I am really surprised here as newer opcom versions (newer than 2016 and every advanced) are not free (as I know),

[Mario6]

Hi,

Does it really work?
Are these really a genuine professional and advanced versions?
Even professional version from 2020?
Does it work on v5 clone version?
Does it need activation?

I am really surprised here as newer opcom versions (newer than 2016 and every advanced) are not free (as I know),

Just try this gift from FANTOMEL and enjoy.

[EduardNN]

Surface mount PCB for OPCOM customization...
transistor bc847

[corsas]

Great post :surprise:

[xJlaIIax]

I cannot download the file in txt format. :(
What am I doing wrong?

[soul87]

Hi, fantomel Thank You very much for this
It works with my v5 cable but I have a question
I have a windows 10 64bit and I found that all versions have a bug, when You start to record live data from measuring blocks program will automaticaly close after 5-10seconds of logging, is there any chance to fix it ???

[xJlaIIax]

Thank you Fantomel.
I was able to download a text file.
I'm Happy! :)

[skycar]

Thank you Fantomel !!!

Great job ...

[fantomel]

Hi, fantomel Thank You very much for this
It works with my v5 cable but I have a question
I have a windows 10 64bit and I found that all versions have a bug, when You start to record live data from measuring blocks program will automaticaly close after 5-10seconds of logging, is there any chance to fix it ???

Inside op-com folder apart from op-com exe you have also LogFileViewer.exe. This file is responsable for live data. Try and put it in compatibility mode and maybe will do the job.

[Lacrooix]

807303807304807305807307807308



Cześć,


Przyjaciele, mam op-com jak poniżej ze zdjęć.


Chciałem zapytać, czy mam odpowiednie urządzenie do konwersji.


W tej chwili działa u mnie program VAUX-COM_120309a + 160115a


Obsługuje samochody do 2016 roku.


Czy mogę skorzystać z przewodnika przyjaciela Fantomela? Jak ktoś może mnie dokładnie pokierować, jak to zrobić?


Pozdrowienia

[Mario6]

Your interface looks like a good Opcom V5. Read "how to use". Install Fantomel software and enjoy.

[Lacrooix]

I installed the software: OP-COM_200603a_EN_Pro_v20830_Free4All


The interface itself has updated to version V01.67


But the problem is that it is not related to the car.


Do I have to do anything after installing the Fantomel program? Any exact instruction? I will be grateful.


USB FTDI 2.8.30.0 drivers are correct?


Thank you very much in advance for your help. greetings

807520807521

[apavlic008]

Thank you Fantomel !!!

[JohnD187]

Thank you Fantomel!

I was able to get the v5 adapter from Ali Express and it updated fine. The only issue is that when programming it gives a "this function is not available" error.

I have tried all the attached versions on windows 7 64bit. It identifies my zafira-b 2013 but no luck trying to enable cruise control.

[Olegs59]

Thank you for the information. I redone my OPCOM NEW, CH-CAN works ,except version 2006003.

[omarzoro]

Thank you Fantomel !!!

[sopido]

Hello everyone!

Is this a good one?
812274 812309

[tottoba]

thank you very much for your work

[Berci18]

Thanks for your sharing :)

[fantomel]

@sopido (https://www.digital-kaos.co.uk/forums/member.php/552562-sopido) Fake pic chip.

[andreobd]

Thank you Fantomel !!!

Great job ...

[ramalho]

Thank you Fantomel !!!

[gdoherty7]

thanks hoping this works for my 64 plate vauxhaul

[abbialy]

Thanks Fantomel, all work well :)

[nightmare1]

Hi Guys,
Maybe someone share
OP-COM 190311a Advanced or
OP-COM 191022a Advanced version?
Working good on HQclone?
Cheers

[paulthejoker]

salve ragazzi ho un clone opcom che dalla foto fantamel sembra buono e non è falso ... comprato su aliexpress .. ho la versione 1.59 per con il software 120309a+131223d che ho vedo errori e alcuni blocchi di misura e nessun blocco di misura motore e altro ancora . .. cosa posso fare per far andare tutto bene? devo aggiornare il firmware? hai firmware e software che funzionano tutti con questo opcom v.5? la mia auto è una opel meriva b anno 2011 A13DTE

foto my driver opcom v5

[/URL]https://i.postimg.cc/Lnpp5kVg/IMG-20200728-023216.jpg (https://postimg.cc/Lnpp5kVg)

https://i.postimg.cc/686xL9g9/IMG-20200728-023254.jpg (https://postimg.cc/686xL9g9)

https://i.postimg.cc/Ln3M1qyC/IMG-20200728-023324.jpg (https://postimg.cc/Ln3M1qyC)

[Mario6]

paulthejoker (https://www.digital-kaos.co.uk/forums/member.php/768181-paulthejoker)


Hi.
Read Fantomel's post number 18 carefully on the page. 2. You have everything there: from manuals to links to his new Opcom software on yandex.
(and english please)

[volodin69]

FANTOMEL IS THE BEST. PUSH THE F*ING BUTTONS FOR THIS MAN. HE GAVE YOU ALL, ON THE PLATE. IF YOU CANNOT HANDLE THE INFO, USE THE SEARCH BUTTON!
And must have V5 version, with ori PIC.

[Mario6]

Mate you are right. I think so too (best regards for FANTOMEL) but everyone started out once and was "green". There were some things he didn't notice.:peaceful:
His version is good V5.

[paulthejoker]

i gave thanks to fantomel but i don't understand which complete software is good to have the engine read in real time and more .. if i have to make changes or not ... my opcom is not HQ but opcom china with real chip..i am to test all these posted? sorry

[volodin69]

I've been testing all. Following his all posts, i have this conclusion. 2016 advanced does all. As original. 2020 proffessional does it all.
Do what you think and test everything, as I did. And... post here,maybe we can all have part of most of the best from our tests. This is all that I want to say. I did my research and posted my conclusion. If you get more of this, just post. Punkt!post edit. Do modify your ori pic opcom to Version C, and all will be good.

[paulthejoker]

thanks you FANTOMEL!!!

[Ser9ei]

Is it a right china's version of the op-com?
The PIC chip is original, and tested.
CAN Transceiver chip is TJA1040 (instead tja1050 as on the V5 version)

op-com_new version:
823875

[Mario6]

Is it a right china's version of the op-com?
The PIC chip is original, and tested.
CAN Transceiver chip is TJA1040 (instead tja1050 as on the V5 version)

op-com_new version:
823875

Hi. Looks like a good "OPCOM NEW" but with the guys from China "you never know". If you can change FW and continue to connect to the car, it's OK.

[fantomel]

These 2 pictures will give u all, related to TJA, l9637.... and so on. I prefer the old ones without standby active, but you can't find them anymore.

https://i.postimg.cc/jqndYMzB/l9637d.jpg
https://i.postimg.cc/C58FCKhw/tja1050.jpg

[Ser9ei]

Thanks, guys, for your feedback!
I tested my OP-COM with the latest software ("OP-COM_200603a") and looks like it work.
Could you please tell, is it possible upgrade my device according to the instructions from the "1.CH-CAN Support(REV.5 ONLY).pdf " manual?

[simple777]

Thank you Fantomel.

Asking for help from anybody.
I've tested different soft versions up to 200603a_EN with op-com downgraded/upgraded from 1.99 -> 1.39 ->1.45->1.67
and had troubles with getting live ECM Measuring Block - parameters:
Motor type: Z18XER
Part Number:55564081 (should be 75.5 with MAP + Air Temp)
SIMTEC75
1) In program I'm getting MAF (Mass Air Flow) with 0 values, instead of MAP (Air Pressure)
2) When press 'Record' button the program crashes all the time (I've read to make LogFileViewer.exe compatible will try, isn't it for Viewing the Logs only ?)

Best regards.

[fantomel]

Thanks, guys, for your feedback!
I tested my OP-COM with the latest software ("OP-COM_200603a") and looks like it work.
Could you please tell, is it possible upgrade my device according to the instructions from the "1.CH-CAN Support(REV.5 ONLY).pdf " manual?

If your device is not a revision 5 PCB then that tutorial does not apply to you.
If you know electronics and circuits then you can study the modification and also the interface diagram and then make a tutorial for other type of interfaces.

[Olegs59]

827628
My opcom_new , the rest as in version 5.0 .
Do not look at the white wire this board repair.

[qwerty1024]

I have a opcom v.5 modified in Type C. I try to work with the program OP-COM_191022a_EN-Adv_v20830_Free4All.exe (190311a_EN-Adv) but it does not connect with any blocks. The program OP-COM_200603a_EN_Pro_v20830_Free4All.exe works well. Does "Advanced" work with Chinese opcom?

[bubimir13]

https://iili.io/fToxkB.md.jpg

If you are curious open and see and you will not be sorry :) I always keep my word.

And a little bit of help to see if your inteface is good or not.

https://i.postimg.cc/dtpzJwXs/Check-FAKE-PIC.png

+ I added down PDF's for CH-CAN modification and also if you like printed boards the project for it.

Enjoy :)
Fantomel


I may be late to the party but thank you for your magnificent work. Works with OPCOM_NEW v1.95 and with both Astra J (in which I programmed Information cluster successfully) and with Insignia B (read and clear deep fault codes).

Hopefully next versions would let us programm the Information cluster and maybe other options on Insignia B and newer models

[SoulSlayerPT]

Thank you fantomel!

[rudoni]

rar парола моля благодаря

[rudoni]

I downloade 150406d_EN 1.64 and asks for my password .pls password.

[Rinoo]

How to download the .txt file?

[Lacrooix]

OP-COM odczyt kodu bezpieczeństwa / przepustki samochodowej / PIN
Jak odczytać kod bezpieczeństwa samochodu?
W załączniku przesyłam zdjęcia jak to wygląda w Astrze J.
Dodam że w Astrze H lub Vectrze C po prostu klikam Security Code i wyskakuje jaki pin jest w aucie.
W Astrze J, kiedy klikam Kod bezpieczeństwa, pojawiają się następujące okna.
Nie wiem dokładnie, co tam kliknąć, żeby przeczytać kod. Czy możesz dać wskazówkę? pozdrowienia

835442835443835444

[cone96]

Anyone know which opcom version to use for CD40 USB? Always got this window(i select cd40 mp3 usb)

837675

[angiorgos]

i do have the 150406b and ask for registration-activation. help please!!!

[Mario6]

i do have the 150406b and ask for registration-activation. help please!!!

If it is Opcom 150406b from Fantomel, install the correct drivers.

[angiorgos]

can you help me pleease with the drivers? i do have from fantomel :)
but what i download is only one .exe. i don't see somewhere drivers

[Mario6]

can you help me pleease with the drivers? i do have from fantomel :)
but what i download is only one .exe. i don't see somewhere drivers

Mate, the drivers are on the "C" drive - x86 program files, in the main Opcom folder. (DRIVER).

Read the software and driver installation instructions.

First Fantomel link.

https://www.digital-kaos.co.uk/forums/showthread.php/821612-OP-COM-SOFTWARE-REQUEST/page2?highlight=opcom

[Nemrod]

Hi, Is it a right china's version of the op-com?

839171 839173

[Nemrod]

Can I downgrade this ver. 1.70 to lower?

[Mario6]

Can I downgrade this ver. 1.70 to lower?

Hi.
Your Opcom PCB looks like a good "Opcom New". D5 and C22 are not visible. It has a real PIC 18F458 at 99%. However, the risk is there.
If you don't take the risk, you won't know. I changed my FW cable from 1.67 to Chinese 1.70 and it works with Fantomel's software.
Unfortunately, I couldn't check on the car because I don't have any Opel.

[Nemrod]

Hi.
Your Opcom PCB looks like a good "Opcom New". D5 and C22 are not visible. It has a real PIC 18F458 at 99%. However, the risk is there.
If you don't take the risk, you won't know. I changed my FW cable from 1.67 to Chinese 1.70 and it works with Fantomel's software.
Unfortunately, I couldn't check on the car because I don't have any Opel.

Ok thank You, I'll try

[ASCM]

Hi i have an opcom 1.39 firmware ori one i tried to use an vaxcom sw with it but when i tried to connect with vaxcom sw tried to update interface itself quickly and i deleted that form but after that i can conect with opcom sw when i try to check fw version show only ??? I writed fw 1.39 with oc flasher sw flashed ok but ahen i trie to check firmware version with opcom sw same thing show only ???(maybe i bricked my opcom with vaxcom sw) does anyone can help me to repair my opcom version 1.39

Sent from my SM-A125F using Tapatalk

[Mario6]

Hi i have an opcom 1.39 firmware ori one i tried to use an vaxcom sw with it but when i tried to connect with vaxcom sw tried to update interface itself quickly and i deleted that form but after that i can conect with opcom sw when i try to check fw version show only ??? I writed fw 1.39 with oc flasher sw flashed ok but ahen i trie to check firmware version with opcom sw same thing show only ???(maybe i bricked my opcom with vaxcom sw) does anyone can help me to repair my opcom version 1.39

Sent from my SM-A125F using Tapatalk


Take pictures of both sides of the interface PCB and post it here. Maybe it has a fake PIC 18F458.

[ASCM]

Take pictures of both sides of the interface PCB and post it here. Maybe it has a fake PIC 18F458.I think its high quality because this tool i bought it in 2010 and it worked perfect until today

Sent from my SM-A125F using Tapatalk

[ASCM]

Take pictures of both sides of the interface PCB and post it here. Maybe it has a fake PIC 18F458.Ok i will open tomorrow and sent photos

Sent from my SM-A125F using Tapatalk

[ASCM]

Here are the photo of my opcomhttps://uploads.tapatalk-cdn.com/20211012/c71cb7500972489cc471a2de6f461ae2.jpghttps://uploads.tapatalk-cdn.com/20211012/a326f1df04d38ba365c2c2fcf90890e3.jpghttps://uploads.tapatalk-cdn.com/20211012/1c6591df1d56677bc1f8dbe0cfa4a1d2.jpghttps://uploads.tapatalk-cdn.com/20211012/ee0422c77419c7ac04ef70bd708eb61a.jpghttps://uploads.tapatalk-cdn.com/20211012/ea8062f8a61b35c1310aeb1c351d05c7.jpg

Sent from my SM-A125F using Tapatalk

[gia]

the links don't work?
I can't download any software.
I have an interface that appears to be a good opcom. with the software they gave me, it gives me "interface communication error or interface not powered from car". how can i solve

[Mario6]

Fantomel's last link with SW still works. (YANDEX yandi)

[gia]

Thank you. maybe I had skipped it. i tried the software but it doesn't connect. searches for the interface and stays there for hours, as in the picturehttps://uploads.tapatalk-cdn.com/20211014/b31d8bdc54ae631b96598b99738d8777.jpg

Inviato dal mio SM-A307FN utilizzando Tapatalk

[volodin69]

Follow all the steps from Fantomels' post and it will work. You have a driver issue. Use CMD uninstall to clear that Vauxcom driver installed earlier, reinstall Fantomel's software and will work ok.

[bar7212345]

Thank you Fantomel

[Nemrod]

845403
Hi, look at the middle foot, is that correct - (not soldering)

[Mario6]

I have two opcoms with PCB "opcom new". One has a connection and the other has no. Both have real PIC 18F458 and FW can be changed. (the one without the housing has no connection. Not working anymore but acted as an HQ clone)
If you don't take the risk, you won't know if he's good.

[Nemrod]

ok thx, maybe I'll try

[nico30]

pass. please OC 150406d EN

[Mario6]

pass. please OC 150406d EN

This software is for HQ clone interface. If you have regular Chinese clone with PIC 18F458 use SW 15xxxxxEN from Fantomel.
The password is in post # 15

[paulthejoker]

hi I downloaded and installed version 16 and the last 20 of fantomel for an opel meriva B engine A13DTE ... I wanted to do a forced regeneration of the dpf but in programming it does not give me the button to do it .. some other button in programming there is like replacing injectors but forced regeneration no ... then it is dimmed and I can't even use OUTPUT TEST..normal? has anyone regenerated with opcom china? is there any other software?

[Mario6]

Once I tried to do a forced regeneration in Opel Corsa D 1.3 DTH 2013. Opcom HQ 160115a PL software. Also, there was no option in "Programing". I was able to burn out the DPF while driving. Regeneration turned on for me 4 or 5 times. I traveled about 40 kilometers during that time. The filling dropped from 200 to 80. I have viewed it in the measured value blocks.

I think the GDS 2 has more possibilities.

[chillaaa3169]

Thank you good work!

[MMK]

Hey


Can anyone confirm if this is the right pic and can this flash.


I would not want to use the included programs because they contain viruses.


Thank you.

[TheSky]

On Ali there is version 1.99, is it good?
Can you recommend a link for a good diagnosis?

[Mario6]

On Ali there is version 1.99, is it good?
Can you recommend a link for a good diagnosis?

Opcoms with Firmware 1.99 have a 99% fake PIC 18F458. A real PIC may have Opcoms with FW 1.70 or 1.95 but not always. You never know what the Chinese seller will ship ..

(I have 2 pcs from the first link but I bought in summer 2021).

When purchasing, please note that SW 200603a or 181022a is made by FANTOMEL and you don't have to pay for them. It is available together with other SWs in this topic .

Check it out here:

[oscarr]

I've tried to use links from 1st page but it looks files has been removed.

Other thing is that somewhere on another thread I've seen that software needs activation for exact interface

To be honest I'm a bit afraid because 1.59 firmware and vauxcom 120309A works, so I was able to set BC in my Corsa.
Thing is that 120309A is slow - I have to wait ages to get program to talk with interface.
Apart of that I feel that in 120309A programming menus are having incorrect options like from other modules. Or sometimes you have just 3 options, but you click next page and then previous, and you suddenly new more options appeared.

So I wonder actually what I need to get never version ? and if will it work better then mentioned vauxcom 120309a?
Is that worth to upgrade if My Cars are Zafira 2004 and Corsa 2011 ?
Thanks :)

[Mario6]

oscarr (https://www.digital-kaos.co.uk/forums/member.php/792811-oscarr)

On page # 2 you have links from Fantomel. One of them (YADI /YANDEX) with Opcom software is still running and includes ADVANCED versions.


If your opcom has FW 1.59 it probably has a fake PIC. If this is the case, after using a newer SW, the FW will be automatically updated and the PIC will be damaged.


The newer Fantomel software is cracked in a similar way to VAUX Com 120309a and on my laptop with WIN OS 8.1 64 bit it works slowly but on the other one with WIN 7 32 bit it is fine.

[oscarr]

I've opened it and there is no D5 and C22 and PCB looks like that:

862874862875

This is auction/seller that I've purchased from:
https://www.ebay.co.uk/itm/154711541759 (https://www.ebay.co.uk/itm/154711541759)

I know you're experienced person, but 1.59 is correct version of opcom firmware.
It was included with vauxcom 120309A in firmwares directory as latest avaiable.
So it is plausible my opcom has correct PIC.

I have also fake pic version of OPCOM and it looks different - the chip has signs of polishing (so was reprinted) and there are D5 and C22.
And indeed it crashed after changing firmware.
Here is photo of fake PCB from aliexpress
862872

PS. I can't find any links on second page - there are PDF files to download only.

[Mario6]

The description provided by the seller shows that the firmware can be changed. .
My Opcom has a PCB like in the first photo, but on the other side there are no electronic components, only soldering.
Just try to use the newer SW Opcom (Fantomel) and you will find out if the seller wrote the truth.


By the way, you will check the operation of two Opcom 11xxxxxEN and 16xxxxxEN ADVANCED SW.
(Download PDF and open. Links are there)

[oscarr]

Great - thanks,

Now I'm trying to follow the guide, and when I try to restore FTDI to file attached to archive I'm getting warning:


File does not match the Device. Should it be programmed anyway?

I'm a bit worried to click yes - so I prefer to ask about that :)

Is there any table which firmware is for which opcom version ?

Is there any most stable/best version ?

Okay. I assumed it don't matter as long as I have backup of my original FTDI.
So I've flashed with 1.67 and it looks it worked but since my laptop has weak battery I'm unable to check in the car without power extension lead.
So will do that tomorrow.

[Mario6]

You do not have to do that . This is the file for Opcom HQ Clone. You possibly need to change drivers, but only if the software asks for activation. Just install newer software and if you want to take the risk, connect the interface to your laptop, then run the software, test and diagnose your chosen car. In case of Opcom 15xxxxxEN your FW 1.59 should automatically change to FW 1.64. (Of course if your PIC is real)
The risk is yours, so have fun.

Opcom 08 2010-FW 1.39
Vauxcom 12, Fake 14,16- FW 1,45
Opcom Advanced 161001a Fw 1.65
Opcom 17xxxxx FW 1,66
Opcom 18, 20xxxx FW 1.67

[oscarr]

So .. I didn't know that Opcom software will update anything and I did use Ocflash and upgraded to 1.67 manually.
Should I downgrade now to let opcom do the thing ?

[oscarr]

I did flash that opcom now 3 times 1.59 -> 1.67 -> 1.41 and back to 1.67
I reverted to 1.41 and used version 15EN by Fantomel to check if there will be any auto firmware update, but it didn't try to do that, so I flashed back to 1.67 manually.
What I've noticed is that latest version by Fantomel (20EN?) has broken "Test Interface" function - it simply don't react (nothing happening when you click on it).

[Mario6]

It means you have an interface with a real PIC 18F458.

For the automatic FW update to take place, you need to do an "interface test" or initiate diagnostics of a module, for example an engine. But since you already have FW 1.67, leave it like that.
(I broke one Opcom with lots of FW changes)


In the software 200603a, the interface checking option does not work.

[oscarr]

Just one more question - do you know if that fake OPCOM from aliexpres can be repaired?
I know that there is proper PIC needed and I need to remove C22 and D5, but some time ago, I've seen somewhere that there is also wire link needed between two points? I had no opcom on that time yet, so I didn't care to save that link.
Another thing is that even if I will fix the hardware - will it work just like that?
I would rather expect I need to flash bootloader to new PIC first. Or maybe there is bootloader by default?

[oscarr]

That was duplicate, please delete.

[Mario6]

You would have to solder a real PIC 18F458, remove D5, C22 and make new connections. Additionally program the PIC using an external programmer. Unfortunately, I also don't have any instructions.

[Achie007]

Thank you fantomel.
Great job hero.

[Achie007]

It works good but i hoped to read the pin from my astra h 1.9cdti unlucky it didnt read it when i try to read the pin from the ecm
it shows me timout occured! and i tried to read it from the display but there it doesnt give me the option to read the pin

[oscarr]

Only very old version of opcom software can read the car PIN from ECU.
It was version 10... or something like that. This means your car may be not supported.

I had similar problem with my Corsa D ecoflex - What helped was cheap CH341A eeprom peogrammer and little tool called OSCR (to be found on this forum I believe).
You need to take off your genuine radio, and open it, you have to get access to eeprom chip - in some models PCB and eeprom is just under the top lid.
In others you need to take CD mechanism off.
You don't need to unsolder the chip - you need just to use crocodile clip with ribbon attached to CH341 (they are sold as set together).
You read your eeprom from radio, and save it as file. You load the file to OSCR and it displays your code (and some other information obtained from radio).

As I remember OSCR you can find with google. I would also suggest you to look for reading PIN from opel radio or something like that. \

For me cost of code extraction was something around 8 quid - not too much, and I have programmer that I can use for other occasions.

[Mario6]

It works good but i hoped to read the pin from my astra h 1.9cdti unlucky it didnt read it when i try to read the pin from the ecm
it shows me timout occured! and i tried to read it from the display but there it doesnt give me the option to read the pin


I read the immo PIN from the engine control unit in Opel Vectra C 1.9 CDTI 150PS (2007y) and Opel Astra G (2002y) 1.8 petrol.


I used Fantomels Opcom 110530a Advanced and 161001a Advanced. I could only do this once. To read the pin again I had to wait some time but I was successful.

[Achie007]

Thanks for the tips guys,i tried 161001a without succes i think i will try 110530a and if that not work i ordered a carprog.

[Gurbettekises]

Thank you Fantomel

[oscarr]

Recently I did try to use Advanced version of OPCOM and I know that Fantomel told users to go every time to settings and set the interface type to B and then go to Diagnostics and try K-line connection, but from some reason interface type selection is gone, and I cant select it. Despite of that, interface seams to react (I hear relay clicks), but second step is also weird - To be honest, I have no idea how to initiate K-like connection, and without that nothing works. Of course version PRO works perfectly - no problems at all.

[prcl]

Hi, been throught 9 pages on forum and can only see schematics on page 2 fron fantomel to alter board. no software or instructions cant fiind.

[Mario6]

Hi, been throught 9 pages on forum and can only see schematics on page 2 fron fantomel to alter board. no software or instructions cant fiind.

Are you sure?

Page # 2
Fantomel wrote:

1) "Click a link and let me know the result.txt"
(yandex link works)

[prcl]

Thanks Mario. I can download the 4 pdf files without problem but clicking on that just keeps taking me back to the log in page

[Deivid Roza]

Sorry for the question but in the face of so many versions and clones. what would currently be the best version to buy with the greatest number of functions and features?

thanks for posting

[hamie55]

Works perfect thanks!!

[chupala]

Thanks,
Got it working, my interface seems to be a good one.
Is there any guide for this ? does it pulls the security pin of the ecu on an astra h ? I have a second hand ecu but don't have the code :S
Cheers

[awesome88]

thanks Fantomel:boxing:

[ibbbo]

Hello to all!

First of all, thanks to Fantomel and everyone else, eager to help people like me :D

Recently, I bought op-com interface - according to Op-com pro it is 1.67 version. With PRO version everything works w/o issues.
But I need "ADVANCED" version, in order to read Security code on my Astra H 2007.
I tried several versions, provided from Fantomel, but in all of them I got one and same error "please connect your interface to the usb port or install the usb driver".
I'm following the steps, but once I change interface to B and go back to "Diagnostics"button, I receive this error, so not even possible to chose car with K-BUS as next steps suggest.
The driver version also says 2.80 so it is not the problem either.

What would be the problem and how to solve it?
I currently cant'open the interface, as it has sticker and warranty will void.

Thanks in advance!

PS: If you know another possibility to found this magical security code? I know I can contact with Official Opel dealer, but it will cost me not small amount of money, moreover if the previous owner changed this code, I will "eat the wood" :)

[Mario6]

Where did you get your interface. From SKLAD66 in Bulgaria?

If so, it is in the HQ Clon version. Fantomel software works with the usual Chinese clone interface, which has a real PIC 18F458. Read the "manual" carefully. There is something like "RESTORE" there. Personally, if the cable is from S66, I would rather buy another good Chinese interface to work with Fantomel software.

[ibbbo]

Hi Mario6, thank you for your answer!
Yes, the interface has been bought from SKLAD66.

So I understood it is not possible to use this one, but another CN version. Okay, I will check CN stores for something cheap :)
Do I need to look for specific data within the description, e.g. to have that PIC 18F458 for example?

[Mario6]

You can probably remake the HQ Clone (S66) interface to Chinese clone. You would have to use the Fantomel file "RESTORE" and OCFlash but there is no guarantee that you will be able to revert back to the HQ version. So you will not be able to use the latest versions of Opcom PRO from S66.

What latest Opcom PRO software does the S66 now offer? (SW 21xxxxxxEN?)

[ibbbo]

The latest version from S66 is 210420b, but it requires registration. That's why I use older one.
I read about the "restore" procedure, but I'm afraid to not brick the interface, as it has warranty.

[Mario6]

The latest version from S66 is 210420b, but it requires registration. That's why I use older one.
I read about the "restore" procedure, but I'm afraid to not brick the interface, as it has warranty.

I bought an Opcom from them 3 years ago when the newest SW was 170823c (also required registration). I asked and they activated me the newer version 181022a for free without any problems. I have provided the purchase date and interface ID.

[ibbbo]

I bought an Opcom from them 3 years ago when the newest SW was 170823c (also required registration). I asked and they activated me the newer version 181022a for free without any problems. I have provided the purchase date and interface ID.

Maybe a bit silly question, but is there any benefit of using most recent software in this case?
I mean, except for extended cars database (but mine is from 2007, so no big deal) is there something as more/ better functionalities for example?

[Mario6]

Opcom Advanced software has more possibilities than PRO. I don't own any Opel, so you'd have to test it yourself. For me it's just a "hobby"

[BLaci85]

Greeting! I want to ask for a download password. Thank you very much!

[Mario6]

Greeting! I want to ask for a download password. Thank you very much!

The password is always the same:

fantomel

[chrisgill]

fantastic brilliant

[Theodoros68]

Hi and thanks ... I need if ok is firmware v 1.65 hex thanks

[Merce101]

Am I missing something? I don't see a link, or an attached file 😭

[sebage]

Yes, you missed it! :)
Read carefully the first post, from the beginning, to understand the purpose of this topic.
Then, access the link to the topic where the download is discussed...

[Jaakko80]

What's the difference in those advanced/professional opcoms.

Still waiting for my HQ clone to arrive so can't try myself.
I have two Insignias and
Wife has K Astra so have been using GDS2+VXDIAG so far but somehow i like opcom more because it has those programming abilities

[gerinemo]

Thank you :-)

[kwat]

hello, could someone make the opcom v1.95 firmware upload

Thanks

[Mario6]

hello, could someone make the opcom v1.95 firmware upload

Thanks

Hi.
What do you need firmware 1.95 for? It's a Chinese trick. Last real FW is 1.67. Changing the FW is only possible if your Opcom has a real PIC 18F458.

[kwat]

has anyone shared a proven FW v1.67 for opcom?
Thanks

[tempra56]

170330a HU 1.65 Professional Does anyone know a link?
Thanks,

[firebroker]

Hello to all,
I have bought an opcom from obd2cartool with real PIC on v1.7. I have downgraded to 1.67 succesfully and I wanted to make a modification to ver.C. When I turned my board on the opposite side I noticed that it looks different from Fantomel guide. see photos. Board is marked as OPCOM_NEW.
Can you advice me please, if it is useless board or can be modified ? and which trace to cut according to manual ?

https://www.obd2cartool.com/index.php?main_page=product_info&cPath=1_3&products_id=1345
948174948175948176
thank you for support

[jusna]

I have v5 interface 2007-12-10
I need software for win10 for opel
Can i have link for download please?
thank you

[jusna]

thank you fantomel

[Ahmet19300]

Opel ve Chevrolet TCU yazılımları varmı sizde

[Sanyamaci]

Thank you :-) OP-COM advanced 161001a functionality is perfect. I have China clone with 1.70 FW (opcom v1.70 newest green PCB board real PIC18F458 FT232RQ support FW flash update).

I hope so the PIC chip is original. I haven't tested it yet. However, it works with the software. (Opel Astra H 2007 - I was able to read useful information, secure code, programming etc…)

In addition, what a plus it is if I use OP-COM after downgrade with original FW?
Is it worth doing the downgrade 1.39 FW, then upgrade to 1.65 FW?

953976 953977

[megaSuperUser]

Got a clone (v1.95) interface
- no D2 and C22
- 2007-12-10
- PIC18F458

looks like I'm ready to go further
VID_0403 PID_6001
Drivers under 2.10.0.0

I'm going to update a FW now. Is the 167firmware.hex the one I need ?

[ballroom]

thanks, it will jelp

[firebroker]

hello,
I am using fantomel's soft and guides on my OPCOM_NEW v1.67
200603a Pro works well, but there is missing "special functions" in engine unit (astra j). Do I need for this advanced version ? but...
191022a Adv is not communicating with car in general, no units are availiable. There is no option to change device Revs...
is there anybody with the same issues ? Can someone help me please ? thank you

[izaac]

thank you vary much

[rudoni]

I have downloaded and installed on Win7 versions 22 and 23 and on launch each asks for activation! Please help! I couldn't handle the activation!

[Ermann]

hi
i want to ask what is the latest opcom version and where can i download it
thanks very much

[lucas39]

please don't forget to say thank you.

[lolful]

Thanks Mario. I can download the 4 pdf files without problem but clicking on that just keeps taking me back to the log in page
Hi, having the same problem here. How did you solve this?

[hARro1]

gone a bit quiet might i liven it up a bit
my 1st opcom, before i knew the story was a china clone fake v1.78,
given the number of opcom versions out there with more comming,
i am thinking about an updated list of pictures to identify real and fake versions.
it should not be a case of luck when buying. we can identify the real ones, let the chinese scamers keep their FAKES. obviously v 1.99 black board is a total FAKE deliberately made to look like a green v1.59 board. a lot of these opcon_new boards v1.70 and v1.95 and those boards labeled v5 with either small or large lettering have NO D5, a v1.95 board even has pads for D5 but NO D5 on the board. a lot have empty C22 pads. one advertises an IRF45K80, No D5??, don't buy.
i must say i like the russian ones, idiag.by
keep up the good work guys
pics i have found some from the forum:

[Pedrom69]

fantomel nie mogę pobrać załącznika

[Pedrom69]

Jakie oprogramowanie do opcom 1.7 z opcją Informacja o pojeździe do Astry J .

[Pedrom69]

Bardzo dobry post , dziękuję. Proszę o opcom do astry j . DZIĘKUJĘ.

[Mario6]

Bardzo dobry post , dziękuję. Proszę o opcom do astry j . DZIĘKUJĘ.

If you have Opcom China with a real PIC 18F458, you can use any software developed by FANTOMEL (Opcom 15, 16, 17, 18, 20.) Everything is on the second page of this topic post no. # 18 link #1. (yandex)
Your FW is 1.70 so check what your Opcom's PCB looks like.
With this FW 1.70 your PIC 18F458 may be fake.
If this is the case, using Fantomels SW will destroy it...
FW 1.70 is a Chinese invention.
The last real FW is 1.67 for SW Opcom 18xxxx, 20xxxx, 21xxxx.

[Krzysq]

Thank you fantomel
Good job, but I have a question whether the modification will unlock access to the functions in OPEL Meriva B 1.7 cdti from 2011.
I can't download the file1. CH-CAN (TYLKO WER. 5).pdf (https://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=783446&d=1612618982) .Thanks in advance for your help

[Tassoss]

Hi friends
I'm new here. I come from Greece.
I have a 2006 Opel Vectra C GTS 1,8.
I try to understand about the OPCOM.
I can't find out which tool and what version, and site i can order to work on my car.
How can i know if the chip PIC18F458 and the other one .... is fake ?
Years ago, i worked well with the VAGS on VW and SEAT.
If anyone, please, can recommend me.

[Mario6]

Hi friends
I'm new here. I come from Greece.
I have a 2006 Opel Vectra C GTS 1,8.
I try to understand about the OPCOM.
I can't find out which tool and what version, and site i can order to work on my car.
How can i know if the chip PIC18F458 and the other one .... is fake ?
Years ago, i worked well with the VAGS on VW and SEAT.
If anyone, please, can recommend me.

Return to post no. #18 page #2 posted by FANTOMEL. Look carefully at the photos and download the attachments.

Your car is old and you will most likely diagnose it even with the lower quality interface FW 1.99 (always a fake PIC) and SW Opcom China 08/2010 or Vauxcom 12xxxxx.


Currently, good quality Opcoms have FW 1.95 on Aliexpress. But buying from the Chinese is like a lottery.

You can also spend a lot more money and buy an Opcom HQ CLONE from SKLAD66 (around 90eur for me) which will work with the new Opcom SWs up to version 22xxxxxEN or DE.

[Tassoss]

Return to post no. #18 page #2 posted by FANTOMEL. Look carefully at the photos and download the attachments.
Your car is old and you will most likely diagnose it even with the lower quality interface FW 1.99 (always a fake PIC) and SW Opcom China 08/2010 or Vauxcom 12xxxxx.
Currently, good quality Opcoms have FW 1.95 on Aliexpress. But buying from the Chinese is like a lottery.

You can also spend a lot more money and buy an Opcom HQ CLONE from SKLAD66 (around 90eur for me) which will work with the new Opcom SWs up to version 22xxxxxEN or DE.

Thanks Mario.
I' ll look and try to understand it.

Just can' t download the attachments.
Seems be disabled

[Tassoss]

Just can' t download the attachments.
Seems be disabled

[Mario6]

Just can' t download the attachments.
Seems be disabled

You are "new" to the forum. Read the "rules" again.
FANTOMEL links work.

read PM


Good luck.

[Tassoss]

Thanks Marios.
Have a happy new year

[Trrrr69]

I don't know if I'm doing something wrong but anonfiles.com seem to by disabled and all the other links are offline except one that asks for credit card info and I don't quite believe that one..

Thanks everyone for any advice and happy new year:santaclaus:

[kosina]

Sziasztok, köszönöm a sok infót.

[Tassoss]

Yes, that's how it seems to me too. Have you already purchased an opcom?

[Tassoss]

Yes, that's how it seems to me too. Have you already purchased an opcom?

[Trrrr69]

Yes, I bought one most likely with fake chip(v1.99 firmware). I'll probably buy another one.

[Tassoss]

Yes, I bought one most likely with fake chip(v1.99 firmware). I'll probably buy another one.

OK, I haven't bought one yet. I'm a bit confused as to which is real and which is fake.
however, I want to order one soon

[Trrrr69]

Well man... Now we can officially say we're dumb:stupido3::stupido3::shakehands:
Yadi.sk link works and there's everything there:palm:

So I downloaded 2019 adv and restore ftdi fron there, installed and flashed my opcom and everything seems to work(will need to try in car too but everything says 1.67).

If anybody is interested I've got mine from here:
https://a.aliexpress.com/_mr74oo0
Option opcom 2021

Sorry to causing fatal facepalm to everyone in this thread.

Happy new year and many brain cells to everyone (mainly me)

[Zeemaister]

Thank You!

[Razor0601]

Well man... Now we can officially say we're dumb:stupido3::stupido3::shakehands:
Yadi.sk link works and there's everything there:palm:

So I downloaded 2019 adv and restore ftdi fron there, installed and flashed my opcom and everything seems to work(will need to try in car too but everything says 1.67).

If anybody is interested I've got mine from here:
https://a.aliexpress.com/_mr74oo0
Option opcom 2021

Sorry to causing fatal facepalm to everyone in this thread.

Happy new year and many brain cells to everyone (mainly me)

I have the same OP-COM like you. Where did you download it? do you have a link?

[Tassoss]

Hello friends
I read a lot of posts here and ended up ordering what seemed to be the best package.
I received this opcom which I am attaching to you in the following documents.
in the ad, as it seems, there is no "D5 and C22" and on the back, the plate writes the date and the version.
In what I received, everything is wrong, even the version in .
unfortunately I placed the order without having an AliExpress account and now I can't locate either the ad or the seller.
Can I work with this opcom? can i install it on win 10 or win 7 only
I would like some help here100686710068681006869

[volodin69]

The answer is clear. Is a bad clone. Use the sw provided by the seller. Other way, you will brick the interface. Drivers are working for win7 and win10 32/64bit.

[Tassoss]

The answer is clear. Is a bad clone. Use the sw provided by the seller. Other way, you will brick the interface. Drivers are working for win7 and win10 32/64bit.

finaly i found the way to contact seller. i m waiting for an answer now
to brick the interface you mean rewire same parts on the board?
i saw same post below here
any way, if seller doesn t anything good, i will search to try it

[volodin69]

Brick comes from real word's sense, literally. Meaning it will block and become useless.

[Tassoss]

Brick comes from real word's sense, literally. Meaning it will block and become useless.

Οk. My English isn't good. I understand you.
Thanks a lot

[Mario6]

Οk. My English isn't good. I understand you.
Thanks a lot

Buddy, read post #182 again carefully and with understanding.

This interface will support your Opel Vectra 2006 but you must use the software: "Opcom China 08.2010" or "Vauxcom 120309a".

[Tassoss]

Buddy, read post #182 again carefully and with understanding.


This interface will support your Opel Vectra 2006 but you must use the software: "Opcom China 08.2010" or "Vauxcom 120309a".

I will read the #182 post, but i can't find the numbers, thanks button, links and photos and others on my mobile device. I will do it an other day on laptop

[Tassoss]

Buddy, read post #182 again carefully and with understanding.

This interface will support your Opel Vectra 2006 but you must use the software: "Opcom China 08.2010" or "Vauxcom 120309a".

Yes, it's SW:"VAUX-COM 120309a+131223d GB". seller sent me cd for it.
If can't return it, i'll try work with this, just only by included cd SW.
Do you Know if works on WIN 10?

[Mario6]

Vauxcom 120309a works on OS WIN 10 64bit but very slowly. Better to use OS WIN 7.
Older "SW Opcom China 082010" runs faster on OS WIN 10.
It's enough for you.

[madrik79]

Guys, i've ordered a new unit as I need to reprogram my IPC panel. Now according to various sites there are 2 variants of Zafira B with no rec in tech2 choosing the wrong variant can cause stuff like rear wipers to not work, So my question is can this software correct this.

[Gordini16V]

Hello everyone, where can i download fantomels software package for opel. Can i have a link for download please?

[capusopp]

Thanks fantomel

I have what seems to be a real pic it came with v1.70 and successfully downgraded to v1.67 an it is still working. I can read everything on my 2005 vectra c but on my astra j all the live data from the ecu can't be read. anyone got any ideas? Should i use a specific version of opcom or i must do the moding?
Thanks a lot!

[Mario6]

Thanks fantomel

I have what seems to be a real pic it came with v1.70 and successfully downgraded to v1.67 an it is still working. I can read everything on my 2005 vectra c but on my astra j all the live data from the ecu can't be read. anyone got any ideas? Should i use a specific version of opcom or i must do the moding?
Thanks a lot!

You can install and test all Fantomels Opcom versions. Then choose the one that is best and meets your expectations. However, you must remember that these are modified versions. Not original.
They can be installed on one laptop. Preferably OS WIN 7 32 bit.

[lololol]

I just bought one AE Opcom that seems to be using v1.70 but every time I try to use record option the software crashes, so I wonder what version addresses this problem. I opened the cable and this is what I found, it shows OPCOM_NEW and no C9 and D5 inside, but still not secure if I could go for 1.67 and if that would correct the problem with the record option. Thanks in advance guys!

1015147

[payomag]

Thank you very much. Wasn't able to download the text file (wanted ADV version), but received your soft with opcom clone...
I have a HQ clone, works ok with 200603a - reading live data, able to program, firmware flash ok etc.
Only thing which doesn't work is SWCAN. I found many posts regarding this on the internet, but no solution.
The relay clicks once when connecting, but not the second time like still waiting for the answer. Do you maybe know what might be the issue? Same problem on fake china clone and 120309a+131223d > Also not reading SWCAN. Ordered opcom from idiag but it will take 4 weeks to come...

[Mario6]

Thank you very much. Wasn't able to download the text file (wanted ADV version), but received your soft with opcom clone...
I have a HQ clone, works ok with 200603a - reading live data, able to program, firmware flash ok etc.
Only thing which doesn't work is SWCAN. I found many posts regarding this on the internet, but no solution.
The relay clicks once when connecting, but not the second time like still waiting for the answer. Do you maybe know what might be the issue? Same problem on fake china clone and 120309a+131223d > Also not reading SWCAN. Ordered opcom from idiag but it will take 4 weeks to come...

View the photo.
The problem may be:
-SW CAN relay
or
- M33897AEF transceiver, (NCV 7356G) .
In my case, replacing the "transceiver" solved the problem.

[prcl]

downloaded these before now its taking is back to the log in page again when clicking the link

[prcl]

have these been updated as a believe last one was about 2017

[Krasdimi]

i cant download fantomels software.... there are no links.... am i doing smthing wrong?

[Gensat24]

Hello. I have an Opel Crossland from 2023. I bought Chinese Op-Com 1.95 and immediately downgraded to version 1.41 using Ocflash. I connected it to the computer, opened the op-com 200603 Fantomel application and it was automatically upgraded to version 1.67. So I connected Op-Com to the car, launched "200603 Fantomel", the interface test was positive, I chose the Crossland X car from 2019 and unfortunately the current modules do not open... read info ... something further and that's it. Sometimes it provides the VIN number and engine type, other times it provides a list of all modules present, but it does not read the information of each module. So nothing can be programmed. I don't understand whether the Chinese device is defective or maybe a different interface is needed for my model. Any suggestions? Thank you




OP-COM Chinese

[pnr2020]

Hi new here where are the links? Are they gone now

[tert05]

Hello friends


Opcom D+ without relay
schematic and board here:


https://www.digital-kaos.co.uk/forums/showthread.php/177036-OP-com-schematic

[IleJomer]

Can some one help me out with firmware 1.67 drivers only?
Thank you in advance.

[FP64]

Tried different versions from Fantomel to install a new DPF on Zafira B 1.7 CDTi from 2011 with Denso ECU. (Thanks Fantomel)
I have a version 5, flashes correctly (now 1.67).
When in programming, I can select the items to program (like km since last DPF install, number of regen since DPF install,...) but I can't input any value for these items.
For most items, this will program the value to zero, but for the counter on regenerations since DPF installed, it comes up with the last value, and I can't change it.
When programming this, it never asks for my car's security key.

Any help most appreciated

Filip