View Full Version : VW Passat B6 2005 immo login
dilick
22nd January, 2010, 04:09 PM
there is a problem with VW Passat B6 2005 immo login pin. All keys are lost need pin from dump attached of dashboard 24C32.
Thanks in advance
cammy25
22nd January, 2010, 04:16 PM
Do you think you can just add a key? Just without preparing the key with 7bytes of component access data?
Did you try to start the car without tacho? maybe im*o isn't there.
dilick
22nd January, 2010, 05:40 PM
Do you think you can just add a key? Just without preparing the key with 7bytes of component access data?
Did you try to start the car without tacho? maybe im*o isn't there.
yeah I am sure that login is there;
lupu_sandu
22nd January, 2010, 07:49 PM
The login isn't in dash m8.
Is in immobox, steering lock and comfort module (i think is in CAN Gateway also, but i'm not sure).
KM: 98656
marinescuv
22nd January, 2010, 08:01 PM
Dash panel insert with
im*obiliser control unit
and diagnosis interface
(Gateway
The Passat, Model Year 2001
tachonow
22nd January, 2010, 08:05 PM
Dash panel insert with
im*obiliser control unit
and diagnosis interface
(Gateway
if model 2001
Sorry! What about are we talking here?
Dilick if you can make a prepared key or buy one please tell us else that loggin is not usefull.
marinescuv
22nd January, 2010, 08:14 PM
imoo box is board what I said.
tachonow
22nd January, 2010, 08:19 PM
imoo box is board what I said.
Ok mate than give him the loggin . You have the dump.
jimthejock
22nd January, 2010, 10:27 PM
if the pin is in the dash file then the file is wrong as it doesnt calculate at all
i think you are looking in the wrong place
tachonow
22nd January, 2010, 10:43 PM
The easy way to get SKC is to read EDC16 eprom 95320 and post it here.
cammy25
24th January, 2010, 06:58 PM
That guy is asking questions while he knows sure where and what!
rest of you who want to know:
In first 3 pages of transponder the SA (security access bytes) must be pre programmed all 7 bytes else Kessy wont accept trnsponder.
So without prepared transponder Login is useless. Login is in Steering collumn, Kessy and ECU. Other units just have SA as corresponding bytes. In Passat most of time you cant get all 7 bytes out of ECU ,but just 6 bytes and you need 7th byte out of comfort module.
But still you need transponder with blank pages ( so TP23 is useless) and right programmer to write these pages in TP.
PremierD
24th January, 2010, 07:24 PM
Was told this ..about the missing byte mate yesterday .... Thank-you for posting it ....Question ,, Would you get the pin code (which is useless ) by running the dump through ICC...?
cammy25
24th January, 2010, 07:37 PM
Piece of cake to get Login out of kessy or EDC16. PPD and EDC17 is harder. Cant find any algo of login in Tacho. Why should tacho have a login?? in B6 tacho is just a tacho.
Do you see any VIN? compare with Golf 5 older models without micronas internal flash. And use own logics
Tonda
28th February, 2010, 07:38 PM
Is possible find login from 95320 in comfort module from passat with ezs with elmos mcu?
mes_cal
28th February, 2010, 10:49 PM
Elmos MCU - you are founding programmer for this mcu ?
Tonda
1st March, 2010, 05:35 PM
no,I think that login is in eep in comfort module.but i do not decrypt dump for find login :(
cange
2nd February, 2013, 02:22 PM
hi all can someone calculate pin from confort module of passat 3c
ic 95320
ypiter
2nd February, 2013, 02:49 PM
hi all can someone calculate pin from confort module of passat 3c
ic 95320
pin 46290
richard27
2nd February, 2013, 02:49 PM
12342 Let It could not be controlled in another Member
igorr
2nd February, 2013, 04:39 PM
Login: 46290
VIN: WVWZZZxxxxxxx9463
cange
3rd February, 2013, 03:50 PM
thanks m8 pin was 46290 ok
what calculator you used to find it?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.