auto com crashed while update need help to reflash again

[fady eid]

i have old gold autocom cdp working great untill i installed the new 2016 version and activated all is okay while i update the tool the software crashed now it show i think bad serial number and cant update fault
my autocom is 2 pcb with bt

[rch11]

And the computer detects it?
Try to update it via WOW.
Wow does it better.

[crouchinggerbil]

i have old gold autocom cdp working great untill i installed the new 2016 version and activated all is okay while i update the tool the software crashed now it show i think bad serial number and cant update fault
my autocom is 2 pcb with bt

You should be able to reflash again. If VCI is red then there is a good chance it will carry on where it left off when you start to flash again. They are pretty hard to kill unless it is a hardware fault.


Your copy of delphi may also be setup for another VCI like 100251. You can edit installation.xml with your VCI serial and you will need Hardware ID to match that serial, then reactivate.

[crouchinggerbil]

And the computer detects it?
Try to update it via WOW.
Wow does it better.

Wow does not do it better actually. If you do through wow it sets device for both wow and delphi. Not a problem if you do not have wow, delphi will still update VCI

[fady eid]

yes pc recognize it ok and also the program delphi or wow detects it but cant update by both wow and delphi and cant show correct firmware now

[fady eid]

while it updating it stopped at 50% now it didnt respond to update just receive msg plug usb or power supply
is there a way to reflash the 29f900 ? or what to do as i think this is possible way now only

[crouchinggerbil]

while it updating it stopped at 50% now it didnt respond to update just receive msg plug usb or power supply
is there a way to reflash the 29f900 ? or what to do as i think this is possible way now only

You can download other firmwares HERE (https://mega.nz/file/z4wxAQgY#NR0gpbD3zOpI8oivdjfvfYgUvi7ebC6_Xdu2ufhK9 8s) , drivers HERE (https://mega.nz/file/6ohynR4K#f4fuLihWgcz9I1k2gH8EP3380xTjaEFsnAsvM078H gA)and HERE (https://mega.nz/file/2gIhDY7Z#KuTQsS6wiY6uXqR6jxJPcyHamKaWX_bVRaeOuaCzN pU)they need to be the same in both delphi and wow so copy firmware folder to wow/ac_diagnosis_module folder.

Update can only be done through USB and not bluetooth.

Try update again with different firmware.

You also need VCI plugged into a car or 12v power supply!

[fady eid]

i will try again to remove the 2016 version and install 2013 and give a try , my questions is how to know my firmware number now after it crashed ?!

[crouchinggerbil]

i will try again to remove the 2016 version and install 2013 and give a try , my questions is how to know my firmware number now after it crashed ?!

Inside delphi firmware folder there is a firm.info file, open it with notepad to check what version you had. If you want i can help you by teamviewer without uninstalling. Send me the details in PM if you want me to help by teamviewer

[fady eid]

hi thank u so much for help i need your help now i think its firmware problem or blacklisted pls check the photos i have tried many pcs , different cables , power suplly

[crouchinggerbil]

hi thank u so much for help i need your help now i think its firmware problem or blacklisted pls check the photos i have tried many pcs , different cables , power suplly

What is the serial for your VCI?

Did you look at installation.xml file to see if they were the same?

[fady eid]

i cant find the installation .xml could u tell me the path of this file

[fady eid]

inside the xml file serial is 100251 what should i do know !?

[crouchinggerbil]

inside the xml file serial is 100251 what should i do know !?

what is the serial of your vci? If you do not know then i cant help you with hardware id.

[fady eid]

i used software to detect the serial it was 30250 many people after my reserch ask to install old version autocom 2011,1 to do update there what is your opinion

[crouchinggerbil]

i used software to detect the serial it was 30250 many people after my reserch ask to install old version autocom 2011,1 to do update there what is your opinion


FOR VCI SERIAL 30250
Edit installation.xml and change serial to 30250 and HardwareID to OLLGDVQTQBLU for (autocom cars) or to KHGYGHIFQSGH for (Delphi cars)
Edit installation.xml and change serial to 30250 and HardwareID to OUHOFPMDXKPU for (autocom trucks) or to MZHAMIZOOSRU for (Delphi trucks)

Then you will need to activate software again.

[fady eid]

after i wrote the serial and hw to installation file the software recognize the tool but test failed and cant update still :S

[crouchinggerbil]

after i wrote the serial and hw to installation file the software recognize the tool but test failed and cant update still :S

Maybe it is time to move on to a newer vci mate ;)

[tango]

your pic with autocom/delphi software is showing serial 20418 ?
so is it this serial or is it really 30250?
you need a stable version of autocom or delphi to do firmware updates (or wow5003 which works better)
if using autocom or delphi best to use 2013.3 and make sure you have the correct instalation.xml file for your serial etc before trying to activate the software
then after all this you can then click update firmware (doesnt matter what firmware is in folder at this time) then all will be ok
if you want newer firmware then copy all firmware files from newer firmware archive to the autocom/delphi firmware folder, replacing all files
then update the firmware again

[tango]

oh and before you ask for newer firmware files (they should be here on forum somewhere) just do all the above first and get your unit working again first

[fady eid]

thank u all problem solved by replacing flash 29f800 with new one then do update all is okay now