immo off KANGOO SAFIR2

[SIMCAR2]

Hello

I would like know how i can immo off RENAUT KANGOO 1.2L year 1999 with SAFIR2

Thanks

[ggpanos]

Use Sweeper tool. 100% tested.
Check at http://www.digital-kaos.co.uk/forums/f114/tms374-decoder-tool-65582/

[SIMCAR2]

my sweeper don't work
when i clic RUN i must wait the bargraph is red??

[obdmaster]

Renault decoding tool from codecard should do this m8, no need for cutting goo off circuit board just rig up, and wait takes 4hrs of clicky t click though m8

[SIMCAR2]

here the dump 27C512:

RapidShare: 1-CLICK Web hosting - Easy Filehosting (http://rapidshare.com/files/352565783/KANGOO.ORI.html)

[SIMCAR2]

could you give me modif file

[SIMCAR2]

I TRY again with tms374 decoder but not result.

some question:

I must power ecu with 9V or 12V is good?
For 27C512 pin reset is 22 or 23?

Thanks

[SIMCAR2]

I test at 9V don't work........

I would like test this tool
It is good tool????

Universal decoding tool for Renault fuel injection ECU (http://www.codecard.lt/immo/renault/universal-decoding-tool-for-renault-fuel-injection-ecu/prod_24.html)

Thanks

[obdmaster]

I test at 9V don't work........

I would like test this tool
It is good tool????

Universal decoding tool for Renault fuel injection ECU (http://www.codecard.lt/im*o/renault/universal-decoding-tool-for-renault-fuel-injection-ecu/prod_24.html)

Thanks

Yes m8, i have that. Do safir2 all the time takes 4hrs m8, fenix 5 1hr 40. Its a good tool very handy

[SIMCAR2]

My ecu is SAFIR2 with 55 pins.
It is good for this
There isn't this model in doc.

Thanks

[obdmaster]

Safir2 are usually 35 pins m8,are you sure its 55 pin?



Here are picture of safir2 pins, 55 pins are usually fenix 5 m8

[SIMCAR2]

It's sure my SAFIR2 are 55 pin.

This car have AC (climat).

I would be sure before buy tool.

Thanks

[MOBILTRONIC]

Try with this info.

[SIMCAR2]

What it is frequency min and max.

I can try with sweep fonction genenator?

[MOBILTRONIC]

With the oscillator I did a lot of ECU SAFIR 2.How turn potentiometer thus changing the frequency can be seen on one of the LED diods.All connections as instructions from a with SWEEPER when the ECU is connected to the vehicle, then turn the potentiometer to lower higher frequency and you hear injectors or one of the relay is then decoded ECU.Before that,cut wire from the im*o-ecu.

[SIMCAR2]

I have a generator, you think i can use it?
If yes give me frequency min / max

[sato-bmw]

solution in pm
Greetings

[SIMCAR2]

I must cut im*o line?
before or after?

[MOBILTRONIC]

Please,post read slowly and wright.I think,post that I was well expressed in it and what to do with all instructions from Tiny Sweeper.

[vevepatronu]

Please,post read slowly and wright.I think,post that I was well expressed in it and what to do with all instructions from Tiny Sweeper.


how much time will take you to decode the safir ecu with your solution m8?

[SIMCAR2]

solution in pm
Greetings

THANKS

Your soluce work weel........


KANGOO 1.2L WITH CLIM
SAFIR2 PACKAGE 55 PINS WITH 27C512

1? CUT IMMO LINE
2? 27C512 TO THE BRIDGE BETWEEN MASS (pin 16) AND THE PIN 22 OR 23 FOR 5 SECOND
IN MY CASE PIN 22 AND I HAVE DONE THE PRIMER BETWEEN 16 AND 22 PIN TO HEAR THE INJECTOR AND PUMP OPERATION
3? DISCONNECT THE BATTERY TO ERASE THE FAULTS OF THE CAR CAN NOT CLEAR WITH THE DIAG

THANKS EVERYBODY

[thunder2]

thanks good solucion

[rwgodoy]

See the PDF procedure
by myself, but it is in portuguese
make shorts in pin of flash memory. and cut pins of immo.
it is not dangerous.