Audi A3 8P White cluster

[ilzul]

Hello! I have tried to adapt the mileage on a Audi A3 8P 2009 cluster with abrites clone. Cluster gone black and message with unknown SW version error.
Is there any way to turn them back on with anything?
I have tried also to read before the writing the eeprom but it has been saved as 00 00 00 00.
Rumors says that i have to use carprog to wake them up.

8P0920932C
VDO H03 0990

Thanks!

[wembleyhill]

Hello! I have tried to adapt the mileage on a Audi A3 8P 2009 cluster with abrites clone. Cluster gone black and message with unknown SW version error.
Is there any way to turn them back on with anything?
I have tried also to read before the writing the eeprom but it has been saved as 00 00 00 00.
Rumors says that i have to use carprog to wake them up.

8P0920932C
VDO H03 0990

Thanks!


digiprog 3 will wake it up 100% tested solution

[A3fDevil666]

Read micronas whit x Prog

[ilzul]

I will meet someone in next 3 hours to take a Carprog 8.2 and try to wake it via obd port. Since it communicate with vcds via obd.


Read micronas whit x Prog
Believe I have to do this JTag or I have to take mcu out from motherboard? It would be first time I read a mcu.

I hope it's not really damaged...

[evgeny87]

I will meet someone in next 3 hours to take a Carprog 8.2 and try to wake it via obd port.
i am sceptical about this but share result...

[ilzul]

i am sceptical about this but share result...
As you though, it didn't worked. It doesn't pass the security attempt, but i tried on the obd port and the cluster on car.
I does work only on bench mode?

[evgeny87]

On car, on bench dosent matter.. carprog just cant help here. Read mcu and eep and send me the files. I can help (for free of course)

[ilzul]

I have read the eeprom after i bricked it (because on first attempt I didn't noticed that reading was 00 00 00).
I have uploaded it below, compared to another 24c32 dump it seems to be complete.

Thanks for your interest.
Can anyone share the xprog cdc3217 reading diagram?

Later edit: I finally found the connection diagram on board, hope it is correct, tomorrow I will last try.
Client have ordered an used cluster in order to adapt it on Volkswagen-Service.
876637876638

[ilzul]

hello! i have managed to read the cdc3217g mcu.
Can anyone see if it is repairable?

[evgeny87]

i sent you something...

[catalinosonesti]

I have read the eeprom after i bricked it (because on first attempt I didn't noticed that reading was 00 00 00).
I have uploaded it below, compared to another 24c32 dump it seems to be complete.

Thanks for your interest.
Can anyone share the xprog cdc3217 reading diagram?

Later edit: I finally found the connection diagram on board, hope it is correct, tomorrow I will last try.
Client have ordered an used cluster in order to adapt it on Volkswagen-Service.
876637876638
Hi
This is the procedure with carprog via OBD.https://www.digital-kaos.co.uk/forums/showthread.php/790211-Audi-A3-8p-cluster-change?highlight=carprog+restore+dash
Best regrads

[ilzul]

Every time i tried on the carprog it went to connection error.
I have tried on car and i have made today connector with 3 plus wires, 3 gnd wires, 2 wires of can and same problem, connection error every time.
I try now to write the mcu on JTAG xprog