VAG-COM/VCDS EVERYTHING

[Roma77]

Wich hardware type is this interface.
https://www.obd2cartool.com/atmega162-vag-com-178-vagcom-178-full-active-enfr-vag-hex-can-crack-cable-p-1516?zenid=m9sgic1oflh6tdilehb116vdh7
HW 0x44 .

[Dynamicdk]

I just bought this USBISP burner, but which pins should I use to program my Hex-V2

[bmw318isblack]

@Dynamicdk: Did you check it first with HWType, maybe the bootloader is enabled?

[flavyus1987]

Check the pins with multimeter or solder 4 wires directly on pins of Atmega.

[alexm1]

I just bought this USBISP burner, but which pins should I use to program my Hex-V2Here you have -hex v2- pinout header.
For usbasp use googlehttps://uploads.tapatalk-cdn.com/20191004/001ff9bae865ada56ff135ca20d4de87.jpg

[flavyus1987]

I have one dead vcds clone hex v2.after changed LM2940 and 2x9241A it came to life with k1 k2 ok, but CAN line is dead.
LM2940 is very very hot after a few seconds.
What's the problem? i don't want to change CAN controlers if LM2940 will be so hot again.

[AleksBas]

Does anyone have a JED file for the ATF HW 46?

[Msmax]

I have one dead vcds clone hex v2.after changed LM2940 and 2x9241A it came to life with k1 k2 ok, but CAN line is dead.
LM2940 is very very hot after a few seconds.
What's the problem? i don't want to change CAN controlers if LM2940 will be so hot again.

Did you test it in a car with CAN bus system?
If the interface is only connected to power (+12V and GND) then the CAN bus is always shown as faulty.

[flavyus1987]

Yes, tested on car, passat b6.
I had change MPC2515 too, same result.i don't have a TJA1050 and quatz.but i think, is to much to work.
It is better to buy a new one.

[Msmax]

Yes, tested on car, passat b6.
I had change MPC2515 too, same result.i don't have a TJA1050 and quatz.but i think, is to much to work.
It is better to buy a new one.

Check what voltage levels you have on your CAN pins and chip power pins...
you can always buy another one...

[bmw318isblack]

The LM2940 is nothing else then the LM7805 (and they can get quite hot :) ).
I would check the voltage around LM2940 (Vin and Vout) and the capacitors around it.
If nothing fund then hook up an ammeter to power supply of the VCDS and
take one chip after another down until you see an drop on the ammeter ==> thats the defect chip.



If you cant find anything after an hour or so keep it as spare and order a new one.

Can't loose nothing ^^.

[flavyus1987]

10x all of you.
I found, in my mistery box two echivalent for tja1050: vn7342 & mpc2551. I'll try with one of them, it is the last chance.
However, original is Ata6551, only speed is different.

[flavyus1987]

Changed Ata with mpc2551 and LM is cold, but CAN still not ready, hmmm....

[hid3]

This CAN Not Ready issue is becoming a sickness... Could you please continue testing until you find a solution?
Hot LM2940 usually means some component is draining lots of power = shorted. In your case it looks like it was either ATA or MPC2551.
Can you check all the tracks on the PCB related to CAN so that the continuity exists on all of them and none of them is burnt or broken?

[flavyus1987]

It is alive now, uhhh...
Change ATA with NV7342, and finally works.
To many components changed, and a lot of time...
And LM have normal temperature.

[hid3]

So what was the faulty compenent you replaced and it started to work? ATA6561?

[flavyus1987]

This hardware was ~~~~ed on a NON VAG car.
Changed LM2940 and Si9241 to have K1 & K2 ok, but LM was to hot and CAN not ready. and after that changed MPC2515, and LM temperature become normally but CAN still not ready.
Finally changed ATA with NV7342 and resistor 120ohm between canL & canH and everything is ok.
Maybe it had old problems, many burned pieces.

[bmw318isblack]

Did you use it on a truck with 24V? IMHO it should make no difference to use the interface on an other car (without haveing the benefits of vcds).

[flavyus1987]

I don't know it's not mine.it is of a friend, nobody try to repair this so hard, because is bad for business.spend a lot of time for nothing, and changed pieces cost almost like new one.
But how i said, i think this had old problems , and now was the end of the line.

[Frederic CM]

Hi there, which is the better HW version : 44 or 46 ?
(VAG COM 18.9 VAGCOM 18.9.0 HEX V2 Interface USB pour VW AUDI Skoda Seat VAG 18.9 multi-langue ATMEGA162 + 16V8 + FT232RQ)

[bmw318isblack]

Hi Ferderic,

IMHO the 0x46 HEX V2, better chip set and volatage regulator dont up heat that much.
And not really a big difference in price, if you use forum vip offer :) !

[alexm1]

If you have the "chance" to buy a cable with this kind of FTDI- with that signature on it- you better think twice because will last about 2-3 times of use and than he "dies".

I will post some pics with both sides and on the rigth/down side an OEM FTDI (I hope). https://uploads.tapatalk-cdn.com/20191007/21058feae348fc2bb345aca3d27d11c5.jpghttps://uploads.tapatalk-cdn.com/20191007/a81f4e7a288e5637b1c349c700c70146.jpg

[bmw318isblack]

What so special about them? Pulled parts?

[alexm1]

Those 3 pcs FT232RL(probablly fake) was replaced because those cables worked only about 5 times and than on Dev. Manager shows Unkonwn Device.

Every piece has same/Identical hand signature on it, the ideea is to not buy a cable with this type of FTDI, I hope I was clear enougth this time.

[Roma77]

quotes : The driver writes zeros to the internal EEPROM of the chip at the address 0x002 (which is just the PID of the device), and writes such a code at 0x03e so that the CRC (located at 0x03f) matches. On the original chip, these operations do not lead to anything, because its EEPROM has a 32-bit organization. When writing a word with an even address, it only buffers, and when writing a word at an odd address, two words are recorded at once. A fake chip records each word, so its PID spoils (it becomes 0x0000). Therefore, the fake chip is normally detected during the first connection (as long as the data in the EEPROM is correct), and after reconnecting it is no longer detected
656866

[liviudiaconu]

As i remember, what you wrote is from that perriod when Microsoft and FTDI destroyed FT clones. But this not happend for now.

Which application used in that screens?

[njoythegame]

As i remember, what you wrote is from that perriod when Microsoft and FTDI destroyed FT clones. But this not happend for now.

Which application used in that screens?

Download it here: http://www.leoniv.diod.club/articles/ft232rl/ft232rl.html at the bottom of the page.

[liviudiaconu]

Can't download. Tried on three browsers: IE, Chr, Mozz

[alexm1]

Link from the cloud for the ftester.657185

[liviudiaconu]

quotes : The driver writes zeros to the internal EEPROM of the chip at the address 0x002 (which is just the PID of the device), and writes such a code at 0x03e so that the CRC (located at 0x03f) matches. On the original chip, these operations do not lead to anything, because its EEPROM has a 32-bit organization. When writing a word with an even address, it only buffers, and when writing a word at an odd address, two words are recorded at once. A fake chip records each word, so its PID spoils (it becomes 0x0000). Therefore, the fake chip is normally detected during the first connection (as long as the data in the EEPROM is correct), and after reconnecting it is no longer detected
656866

You or another saw this situation VID_0403&PID_0000? Asking because i saw 2-3 times this. But this combination was generated by V(D$ itself, damage AT eeprom and FTDI eeprom. Old versions and before 2.08 FT driver. The rest of times i saw "Not recognized" VID_0000&PID_0000. And this is because of bad China clone FTDI defective after few use, one of +/-/D+/D- desoldered or interrupt, "STC" or "AES" defective, etc.

[Roma77]

You or another saw this situation VID_0403&PID_0000? Asking because i saw 2-3 times this. But this combination was generated by V(D$ itself, damage AT eeprom and FTDI eeprom. Old versions and before 2.08 FT driver. The rest of times i saw "Not recognized" VID_0000&PID_0000. And this is because of bad China clone FTDI defective after few use, one of +/-/D+/D- desoldered or interrupt, "STC" or "AES" defective, etc.
This is just information and a program that can be used to verify a supplier should not be taken as a panacea for problems. It will be useful to someone, and someone will ruin their scanner, but it was not my fault that I did not put the program in the public domain.

[liviudiaconu]

You understud me wrong. Maybe my english is bad.
I only asked statistics how many times you saw the situation "0403/0000". I'm not saying that application is not useful.
And I said that I only saw 2-3 times that situation but created by "V (D $ .exe", not the driver, sometimes that VID / PID being different (5211/0000, etc).
Most "0000 0000" are due to poorly made FTDI clones.
I did not bring any reproach to anyone. Sorry the date meant something else.

[Roma77]

You understud me wrong. Maybe my english is bad.
I only asked statistics how many times you saw the situation "0403/0000". I'm not saying that application is not useful.
And I said that I only saw 2-3 times that situation but created by "V (D $ .exe", not the driver, sometimes that VID / PID being different (5211/0000, etc).
Most "0000 0000" are due to poorly made FTDI clones.
I did not bring any reproach to anyone. Sorry the date meant something else.
You have nothing to apologize for, our translations into English incorrectly convey thoughts to each other, everything is ok. “0000 0000” is a very bad clone and needs to be replaced; do I often encounter such situations? Yes often, because I myself do them for myself and experiments. All is well, friend, do not apologize, you know that I am very nice to you.

[hid3]

Actually V (D $'s driver is nothing more than a customised FTDI driver. We all know the German man and his philosophy, so... No surprise at all :)

[jakuza]

Does anyone have a JED file for the ATF HW 46?

Thanks to Elektrik and his hard work for couple weeks on this - yes there is.
It is on this thread, I mean about 100 pages before, so just use search.

[sorinc98]

i have a vcds 18.9 cable . at start works ok, but now i m just getting an error " too many communication errors " i try reinstall but nothing work, what i can do ??

[alexm1]

What you see on "About"? License Status is Invalid or Valid?

[sorinc98]

the cable does not connect to the car and idk why, i try different car but nothing chagen. first work about 5-6 times and now no chance to get it. i try reinstall but no succes658862 this say when i connect just the cable to pc but when i connect to the658863

[alexm1]

Share some pics with both sides of PCB. Pics should be taken close to the pcb and with good resolution.

[Fabio89]

Guys

Anyone know why clone version still doesn't work on New Polo MQB ? It works on Tiguan Mk2, New Jetta GLI 2019, Golf mk7,5 but in New Polo shows messagen of "old interface".

[Domi]

only V2 interface Genuine suport UDS protocol

[FastFast]

Where can I download the HEX-V2 scheme? Or differences from V1.

[azza2]

Loader v9.2 released! It improves compatibility with non English versions and VCDS 19.6.0 version.


http://ge.tt/6I9tkOx2
https://www101.zippyshare.com/v/biPvu9Lt/file.html
https://www.sendspace.com/file/5qr55f
https://uptobox.com/l96rbs2lo9h6


Kolimer ......
Thank Kolimer very much.


I used VCDS 17.1.3 English before. It seems like cable version was 1.96, I am not sure.


Few days ago, I checked cable with the tools and flashed it.
Then I installed VCDS 19.6.1 ZHS downloaded from official website.
It's working fine when I am doing autoscan twice and enter ABS module, clearing fault code.


I got "communitation error" few times when I was clearing fault code in ABS module and entering the module last night. This error appeared when I was trying 19.6.1 ENG first last night.
Then I used ZHS back, no error at my same operation. But, I got the error with ZHS too after that. It's not appeared everytime, occasional. I can use 19.6.1 ZHS to do something successfully still.


Another question btw.
Since I upgraded my Instruments to "L5K D92 087 3" from "5KD 920 870", and upgraded VCDS 10.6.4 to 11.11 12.12 17.1.3, I got a popup message "no rod file found" which is caused by following.
----
Part No SW: L5K D92 087 3 HW: L5K D92 087 3
Component: KOMBI H43 0458
Revision: X0043005 Serial number: 00000000000000
Coding: 170A01
Shop #: WSC **07 0** 104**
ASAM Dataset: EV_KombiUDSMM9RM10 A04709
ROD: N/A
VCID: 4D9B02C11C34B3709AA
No ASAM data for: "EV_KombiUDSMM9RM10" ()
No fault code found.
---


I still got this mesage after I upgraed cable and use 19.6.1 whatever ZHS or ENG downloaded from official Chinese website.


I checked some forums for this. Some guys don't have the "No ASAM data" for this Instruments like following.
---
Part No SW: L5K D92 087 3 HW: L5K D92 087 3
Component: KOMBI H43 0458
Revision: X0043005 Serial number: 00000000000000
Coding: 170A01
Shop #: WSC 00079 790 00000
ASAM Dataset: EV_KombiUDSMM9RM10 A04709
ROD: EV_KombiUDSMM9RM10_VW36.rod
VCID: 4D917A3E1C938276201-8018
---


So, how can I solve this problem?

[kaalis]

Those part numbers could be specific to China market in which RT has no interest. Find someone with geniune cable, scan the car with it and ask him to post in RT forum.

[azza2]

Those part numbers could be specific to China market in which RT has no interest. Find someone with geniune cable, scan the car with it and ask him to post in RT forum.

Some guys got it working which also using ZHS version. See the last part of my last post.

If is there a way to solve that with relpacing rod files. I didn't succeed yet by this way.

[kaalis]

19.6.1 ZHS doesn't have that file. Could be one of 3x EV_KombiUDSMM9RM10_VW*.rod is copied as EV_KombiUDSMM9RM10_VW36.rod
Hell knows. Ask in forum who posted those logfiles.

[kaalis]

19.6.2 AIB, PCI, DRV release.
19.6.1 second update for MFT.
19.6.2 NEZ release.

[rak183]

19.6.2 released for AIB, PCI, DRV.
19.6.1 MFT.

Working with loader 9.2?

[heshamzn]

Move the arrow on the left down it will work this reply to Fredrik0

[Kev137]

any suggestion where to buy a good vcds tool?

[bmw318isblack]

@Kev137:

I am with the here in this thread mentiont HEX V2 interface (technically its a V1) very happy.

[kaczucha8]

Dear colleagues

I need reset ash mass in Vw T6 2.0 TDI CXE but I don't know login for ecu.

Can you help with this problem?

Thanks in advance.

[ricig82]

Dear experts,
probably my question was asked 100 times before. Unfortunately all my search results gave not a useful result. I'm searching for a Package of Label Files for importing to Carport. I yust converted the files from VCDS. But the most fils I need are not LBL but CLB files. Is there a package with further files anywhere?
Especialy a label file for 1K0 907 530 is what I'm looking for. Thats for my diagnostic interface (interface 19).
Anybody has any advice for me :itsme:?

Thank you.

[psgpol]

It would be nice to have separated standalone thread ONLY with last version of VCD$ and loader without comments, because now we have 604 pages of different data, lots of stuff but if you wish to answer friend for a question: "what is last working version..." it's impossible to find it in less than 30min :), sometimes like for version 19.6.0 there was a problem with oil reminder reset and such info would be nice to have in that closed thread
Could any of MOD create such thread? maybe with loader and maybe only info about vcd$ version which is possible to run

[Lolo4321]

19.6.1 Works fine with V9.2
Would it be possible to use Hex Can cable with VAG CAN Pro software?

[Mario6]

19.6.1 Works fine with V9.2
Would it be possible to use Hex Can cable with VAG CAN Pro software?

You cannot use the vcd$ cable with the vcp + k 5.5.1 software. Just buy vcp + k on Alie ... for $ 10-18. Unfortunately, not everything works and not enough information on how to use the software ..

[jakuza]

It would be nice to have separated standalone thread ONLY with last version of VCD$ and loader without comments, because now we have 604 pages of different data, lots of stuff but if you wish to answer friend for a question: "what is last working version..." it's impossible to find it in less than 30min :), sometimes like for version 19.6.0 there was a problem with oil reminder reset and such info would be nice to have in that closed thread
Could any of MOD create such thread? maybe with loader and maybe only info about vcd$ version which is possible to run

Some of RT versions have bugs, you can always use latest thanks to kolimer. So, no need to search anything. Also, you can use latest loader with previous stable version, let's say 18.9.0

[voltekk]

hello

is it possible to program an new trottle valve with vcds 18.9
audi a5 2.7 tdi 2008?

[kaalis]

19.6.2 HGJ and ROJ released.

[dudzsi]

Hello! 19.6.2 HGJ work 9.2 Loader?

[obdcarsale]

662088

662089

662090

662091

VCDS HEX-V2 Pro version,items Form aliexpress. For Official software.

but only english, who can crack Russian version?

thanks

[Col19]

VCDS HEX-V2 Pro version,items Form aliexpress. For Official software.

but only english, who can crack Russian version?

thanks

Hi dear friend Obdcarsale,

Your sharing interests me a lot,

can you please share the seller's link by PM ?

Thank you so much.

[Tib82]

Hello! 19.6.2 HGJ work 9.2 Loader?Igen, működik :) (Yes, it works)

[papuc]

662088

662089

662090

662091

VCDS HEX-V2 Pro version,items Form aliexpress. For Official software.

but only english, who can crack Russian version?

thanks
Can you show us PCB please? Both sides. I tried looking for this cable on Aliexpress but I couldn't find it. Is this the holy grail with the ARM chip?

[tk500]

VCDS HEX-V2 Pro version,items Form aliexpress. For Official software.




Try to update firmware.

[dudzsi]

Igen, működik :) (Yes, it works)

Köszi! Thanks! :D

[exantas]

Can you show us PCB please? Both sides. I tried looking for this cable on Aliexpress but I couldn't find it. Is this the holy grail with the ARM chip?I had one of those with arm chip. It works out of the box with official / unmodified vcds. In my case worked two times, but the third time couldn't find my cars can bus.
The seller is creating the adds only over the weekends and deletes them during the week. https://uploads.tapatalk-cdn.com/20191027/59f2e16c205b980201a1e90b21190522.jpghttps://uploads.tapatalk-cdn.com/20191027/909da2ac6e113d80511af707e05d53f0.jpg

Sent from my MI 5 using Tapatalk

[exantas]

Here is the seller in Ali express https://uploads.tapatalk-cdn.com/20191027/16f69185f6adbf63b102366205382c84.jpg

Sent from my MI 5 using Tapatalk

[papuc]

Does port test tell you that type is a HEX-V2? CB and FW? If Ross-Tech HEX-USB+CAN I'm not interested.

I thought it had and STM32 chip and not HL008 ARM chip with 1.96 FW.

Edit 3: I see two of those "Only English" "Style B" HL008 ones on Ali. Both of them are 18.9 and they claim to support UDS. But no Port test window. No updates also.

[bg17aw]

I had one of those with arm chip. It works out of the box with official / unmodified vcds. In my case worked two times, but the third time couldn't find my cars can bus.

Did you use it with internet access on?

You should keep internet off at all times to avoid the cable communicating with RT servers which would result in a ban of the serial number.

Do you still have the cable? Can you post c-test.exe screen with cable connected to a 12v source (can be the car, of course)

[bg17aw]

sorry, bad post

[exantas]

I never connected it to internet (although the seller was claiming that its safe to do so). I sold the cable, but before that I downloaded latest vcds 19.6.1 and connected the cable to 12v and it still showed as activated in about page.

[exantas]

Does port test tell you that type is a HEX-V2? CB and FW? If Ross-Tech HEX-USB+CAN I'm not interested.

I thought it had and STM32 chip and not HL008 ARM chip with 1.96 FW.

Edit 3: I see two of those "Only English" "Style B" HL008 ones on Ali. Both of them are 18.9 and they claim to support UDS. But no Port test window. No updates also.

Yeah now I saw it , my cable is HEX-USB+CAN.
I didnt see the picture from obdcarsale that showed HEX-V2.

Sorry for that

[liviudiaconu]

Hello! 19.6.2 HGJ work 9.2 Loader?


Igen, működik :) (Yes, it works)


For sure work? Tested OK?
Because i tested 19.6.1 ROJ and HGJ with V9.2. ROJ Work, HGJ not work. Not only "Test" OK..green serial. No, tested more actions.

[obdcarsale]

662394

PCB STM32F415 ARM chip!

[papuc]

662394

PCB STM32F415 ARM chip!
Oh WOW! Now we are talking! This is the unicorn! 20190902 All we need is now where to buy this. At least I'm interested. Would appreciate if you could reply to my PM if you don't want to post source publicly.

Edit: Took a look at this and seems like this was a well kept secret. No wonders I couldn't find it on Aliexpress. With the right search terms you only get one result and the one posted by obdcarsale. No labels, no PCB shots, nothing. This might be end of the old old HEX-V2 era.

[hid3]

Please do not post any links to the real V2 clone publically due to known reasons.

[tk500]

No need to hide.
Software calling home.

[papuc]

No need to hide.
Software calling home.
I don't think you get it but that's alright. It's not about software calling home. It's about them taking down the listing.

[exantas]

I don't think you get it but that's alright. It's not about software calling home. It's about them taking down the listing.Hey if you get the listing and you want to, can you send me the link please?


Thank you for your time,
Exantas

Sent from my MI 5 using Tapatalk

[papuc]

Try to update firmware.
From the Port test window you can only see FW (Firmware) and CB (Code Block) version. They are up to date if you take a look at RT forum changelog for HEX-NET. There might be newer firmware version for HEX-NET but that's because it's a different product and has wireless. We cannot see BL (Bootloader) and DS (Dataset) versions and CFB (whatever this is). You can only see the version numbers for these in the \/CDS Interface Config tool. And who knows what kind of serial number the cable has. (I would hide that in screenshots). If you launch the \/CDS Interface Config tool that might phone home or brick cable, but it's hard to tell with not that many units sold for this new cable. We need guinea pigs I guess... Do at your own risk.

[hid3]

Even HEX+CANs have the "counters". Each time you plug in the interface into the OBD2 port, the count is increased by 2. It also stores adaptations, codings changed, DTCs cleared count too. All these counters go one way but never backwards.

Upon \/CD$ installation, it puts into system's startup file, which connects to their server. Even when you launch the program, it reports to the server those numbers (along with serial, MAC addresses of the PC, etc).

If the server detects that multiple interfaces are reporting at the same time or the count somehow goes backwards - boom, blacklist, license revoked in next version.

Do you think "next gen" interfaces as V2 and NET do not have "counters"? :) Then think once again!

[papuc]

I'm not telling you that there's absolutely no spying. We don't even know if STM32 clone has a crack/loader or if it can be updated. Only one has been sold so far. Time will tell what happens with these cables. Use them until you can I guess and hopefully one of these cables gets to kolimer.

[kssj0001]

Even HEX+CANs have the "counters". Each time you plug in the interface into the OBD2 port, the count is increased by 2. It also stores adaptations, codings changed, DTCs cleared count too. All these counters go one way but never backwards.

Upon \/CD$ installation, it puts into system's startup file, which connects to their server. Even when you launch the program, it reports to the server those numbers (along with serial, MAC addresses of the PC, etc).

If the server detects that multiple interfaces are reporting at the same time or the count somehow goes backwards - boom, blacklist, license revoked in next version.

Do you think "next gen" interfaces as V2 and NET do not have "counters"? :) Then think once again!


Hi guys. Sorry about my poor english. Just let me give you some info.
Yes now we can buy this 1:1 V2 clone on Chinese market. But it's more expensive, even more than VAS5054A clone.
And the most important, the SN No. on clone chip may be disable by R0SS-Shit company in the next version.

So now it's not worth to buy. We must make sure the ARM chip can be flashed and someone can make patch like kolimer.

[tk500]

No need to wait for next version for serial number disable.

[azza2]

19.6.1 ZHS doesn't have that file. Could be one of 3x EV_KombiUDSMM9RM10_VW*.rod is copied as EV_KombiUDSMM9RM10_VW36.rod
Hell knows. Ask in forum who posted those logfiles.
It seems solved by copying new label file from a exist instrument labe file.

Thanks.

[Jay1908]

Hi guys could someone pm me the link please? I would really appreciate it.
Recently bought a cable that stated 'hex v2' and '19.6' but on port test its a 'hex usb can' and it doesnt work on 2019 cars.
Thank you guys

[kaalis]

Yeah, I also would like to buy '19 audi for 300usd and spare 199usd without buying hexv2 (3 vin) for oil and belt change... All this is ridiculously expensive. I can afford a new car but cable is too steap. How could you RT do this to us.

I'd better buy currently unknown cable for 50% and hope it's ok. :D Seller was autodiagstore or something like that.



Sent from my SM-J510FN using Tapatalk

[kssj0001]

You can buy VAS5054A clone for MY2019 audi, full function and less than 100usd. The only thing is ODIS is a big shit program use java...

[Jay1908]

Yeah, I also would like to buy '19 audi for 300usd and spare 199usd without buying hexv2 (3 vin) for oil and belt change... All this is ridiculously expensive. I can afford a new car but cable is too steap. How could you RT do this to us.

I'd better buy currently unknown cable for 50% and hope it's ok. :D Seller was autodiagstore or something like that.



Sent from my SM-J510FN using Tapatalk

I never said i own a '19 car i said it doesnt work on a 19 car. Doesnt mean i own one does it? All that sarcasm for nothing. But thanks anyway.

[Jay1908]

Thank you kssj0001 but im not familiar with odis and ill rather stick to vcds. Ive been looking for the 1:1 V2 clone still cant find it. Help pls

[hid3]

What is the exact reason you're looking for the 1:1 V2 clone?
Name at least a few of them and you will get the links.
Cause at this point, everything can be done using the classic one

[Jay1908]

What is the exact reason you're looking for the 1:1 V2 clone?
Name at least a few of them and you will get the links.
Cause at this point, everything can be done using the classic one

Im after the hex v2 because the classic hex+can doesnt access certain modules on 2019 vag cars for coding. My last cable that i had for a few years was a 15.7 which is a little outdated so i thought ill get the most up to date version which is a 19.6.1 i believe? Im in the process of returning the 19.6 hex+can cable that i bought recently so i can get a hex v2 that works with all cars including the newest ones.

[kssj0001]

Thank you kssj0001 but im not familiar with odis and ill rather stick to vcds. Ive been looking for the 1:1 V2 clone still cant find it. Help pls

Sorry Jay I find it on local, it's not support international express. But as I said you don't know how long you can use this clone. R0SS-Shit can disable your license anytime.

[kssj0001]

What is the exact reason you're looking for the 1:1 V2 clone?
Name at least a few of them and you will get the links.
Cause at this point, everything can be done using the classic one

The classic one can not support some new MY2019 cars and some modules. Like MQB POLO, T-ROC, T-cross. Maybe all the MQB-A0 cars. Of course I know it's trick from R0ss-Shit. For selling their new products, unscrupulous.

[Tib82]

Is anybody met with this type of PCB? The owner got v1.12 L0AĐ€R for it and a complicated registration method.
Is it good, average, or bad version? Can it use K0L's stuff?
663793663794

[jan4]

done a hwtest ??

[robinbga]

Is anybody met with this type of PCB? The owner got v1.12 L0AĐ€R for it and a complicated registration method.
Is it good, average, or bad version? Can it use K0L's stuff?
663793663794Yes it can run with Kolimer's loader v9.2 but u have to make sure u use the V1.12 loader to unlock it first.
It's should work

Kess V2 . K-Tag
MiniPro . UPA . VVDI2

[andrei_hrz]

Helow. I have this vcds it used to work with 908. Now a bought a car and it is not working with it. Please cand I update it?? I have this pictures whit it.663913663914663915

[kaalis]

What are you waiting for? Run infotool about cable and then choose solution from pdf.

Sent from my SM-J510FN using Tapatalk

[andrei_hrz]

This is the problem. Don`t find the infootool and the other sofware(.bin) to write with my usbtoavr on the AMTEL. I read about 100 pages and I didn`t find a post with them. Can you help me find te post? plsDownload::embarassed:

[kaalis]

Do a search in posts (results shown as posts not threads/topics) from user Kolimer and you will find it sooner than Christmas. :)

Sent from my SM-J510FN using Tapatalk

[andrei_hrz]

I have tried to find out what tipe of cable I have but I have this error ? :(663947

[vcdss]

i got a chinesee vcds version 14,
on the CD there are many installer versions 11, 12, and 14.
but there is only dll file(crack ?) for version 11?
there is no dll or loader for installer 14.
where can i find loader or dll or something so it can work with version 14.
i already sent message to the chinese seller but who knows if i will get the answer from him and when

i tried kolimer 9.2 loader with this 14. installer that is on the cd but it does not work, says interface not found.
only combination that worked is russian installer 11 and checz dll file for 11

[morton01]

Hi,

Can anybody assist with security key codes. I am trying to do a forced DPF regen on a 2008 A3 (8P). Is there a list of codes available anywhere?

Cheers

[kaalis]

I have tried to find out what tipe of cable I have but I have this error ?
Is cable recognized in windows device manager? Did you attach it to obd2 port or 12v on a bench?


Sent from my SM-J510FN using Tapatalk

[andrei_hrz]

No I did not put 12v on bench :( .
Later edit:

I manage to make it work. Thank you for your help https://uploads.tapatalk-cdn.com/20191104/a7df81c397aed020bdc72e2e2735e85f.jpghttps://uploads.tapatalk-cdn.com/20191104/f346d5ca09b99b088980c43f8fda4bd4.jpg

Later later edit:
After 3 minuts of using it. I got an error to test it. I tested the cable that was conected to car, but the error remaid “the cable is ok, but not conected to the car” :(.

Sent from my iPhone using Tapatalk

[nextor]

A neighbor is telling me that he can sell me a real HEX-V2 clone. He insists that it's indeed a HEX-V2 clone, not just a HEX-CAN clone in HEX-V2 case. Is this possible? I knew that there are no real HEX-V2 clones. What do you think?

[tk500]

HEX-V2 clones already exist.
But their lives will be short.

[Jay1908]

All the hex v2 cables ive found are just hex+can in a hex v2 case. There is this european one that ive found thats a 19.6.2 claiming it works on all cars including newest. Since you guys dont want to share the link to the hex v2 clone ill have to do trial and error on these cables till i find a working hex v2. Ill let you guys know how it goes.

[kaalis]

You can read seller name, pm him, you can read shop name in Ali, scan his listings, what else you want? Links to exact listing lasts for couple of days maybe and then change/get deleted/whatever reason.


A neighbor is telling me that he can sell me a real HEX-V2 clone. He insists that it's indeed a HEX-V2 clone, not just a HEX-CAN clone in HEX-V2 case.
Ask for screenshots from Device manager with cable entry, port test and About screen from vcds.
Should be enough for a start.

[nextor]

All the hex v2 cables ive found are just hex+can in a hex v2 case. There is this european one that ive found thats a 19.6.2 claiming it works on all cars including newest. Since you guys dont want to share the link to the hex v2 clone ill have to do trial and error on these cables till i find a working hex v2. Ill let you guys know how it goes.

What do you mean by "european one"?

[Lolo4321]

Does someone have an example how a EGR Delete, and DPF Delete looks in VCDS under measuring blocks ? How do i spot a EGR Delete and DPF ?

[papuc]

All the hex v2 cables ive found are just hex+can in a hex v2 case. There is this european one that ive found thats a 19.6.2 claiming it works on all cars including newest. Since you guys dont want to share the link to the hex v2 clone ill have to do trial and error on these cables till i find a working hex v2. Ill let you guys know how it goes.
There's two clones on Aliexpress. One only mentions chip with a generic housing, the other has board shots but both of them are expensive. With little search you can find them easily. When you see the price you know you got the right item.

[Jay1908]

You can read seller name, pm him, you can read shop name in Ali, scan his listings, what else you want? Links to exact listing lasts for couple of days maybe and then change/get deleted/whatever reason.


Ask for screenshots from Device manager with cable entry, port test and About screen from vcds.
Should be enough for a start.

What more do i want? The link ofcourse. Which i did ask for. But i got asked the reasons for why i want it then i would get the link but i didnt get anythimg hemce why i said i would have to trial and test different cables to find a hex v2.
In regards to the european one that i mentioned , afaik the chinese clones dont have a 19.6.2 but a few european sites have it. I may be completely wrong about this and it could just be another hex+can cable

[papuc]

What more do i want? The link ofcourse. Which i did ask for. But i got asked the reasons for why i want it then i would get the link but i didnt get anythimg hemce why i said i would have to trial and test different cables to find a hex v2.
In regards to the european one that i mentioned , afaik the chinese clones dont have a 19.6.2 but a few european sites have it. I may be completely wrong about this and it could just be another hex+can cable
I think i know why you didn't get a link. That is because you won't get a link in public. Also you are a new user and not being on this forum for more than a week. You could be RT employee (I'm not telling you are but you must build up some rep in here). Plus if you know the link you wouldn't buy a cable anyway because right now there's no point to buy one. It's way too expensive and the risk of getting it banned it quite high. If you really want one you can find both of them quite easily. You know what MCU the original HE>< V2 has. It's just a matter of one search and a little sorting. The other even more expensive cable has PCB shots in the listing so that's also easy to find. If you can prove it that you are capable of finding any of them and send a PM with a link to me I'm going to tell you if it's the right link or not. How about that?

[rak183]

Here is a link for V2. The seller didnt put pictures of thr Software.

€ 62,93 | HEX scandiag kabel V2 vag kabel 19,6 für vw für audi für sitz für skoda obd scanner update kostenlos
https://s.click.aliexpress.com/e/pF5IFV3tv

[papuc]

Here is a link for V2. The seller didnt put pictures of thr Software.
Nope. It's not € 62,93. That's the Atmega one like it says in the description. Click on "v2 19.6" € 159,60. You should remove the link. Seriously. There's a much cheaper one out there that costs little over € 100.

Edit: Oh well... people can't keep secrets. You might as well post the other one as well. So get them before RT magic trick with the link and cables.

[Jay1908]

Thank you rak183 i really appreciate it.
Papuc is right though you should remove the link before it gets permanently removed.
@papuc what makes the cable get banned? Is it cause of going online? Is it because of updating the software?

[papuc]

@papuc what makes the cable get banned? Is it cause of going online? Is it because of updating the software?
Ask RT. Having some common sense also helps. There's not only VCDS, there's firmware on the cable as well. They can brick cables if they want. I'm sure they can code some routines to check if it's a genuine He>< V2 or if it came from China. So you might be stuck on the same 19.6.X version forever, especially if you cannot reprogram the cables. Chink sellers might be able to do that but they ain't gonna tell you how nor give you a hex or dfu. You don't know if you can update the shit on the cable with the official ones from RT servers. For Hecks+CAN the firmware came from a local file from VCDS installation folder rather than a remote location. There's actually bin files if you take a look. While for genuine Hegz v2 there's a tool that downloads them and phones home with probably too much information that's encrypted. Buy a cable and try in and capture traffic with Wireshark if you can throw out the window 100+ Euros. You might as well buy an ST-LINK v2. Maybe you are lucky and there's no read protect on the MCU unlike the genuine cable.

So yeah. You don't have a loader and toolset to fix bricked units like you do with Hecks+CAN. Kolimer ain't gonna help you so don't bother him with. You got to start from the beginning and take down the empire again till they run out of space on the MCU and RT decides to use something else with more space on it.

I would experiment with the new clones if the prices were only 1/3 the price. The problem is that mofos in China have way too much old old clones in stock. Somehow those must go. Also they won't tell you what they did with the cables or how they function. No installation videos, not mentioning the new MCU or if they can be updated or not. So wait and don't post links. If they update cables after a new VCDS version and sell the same cables then there's hope. If the same listings stay on the same version then it means only the person who reverse engineered knows and has the ability to fix the cables. Keeping that as well a secret means that resellers won't have the ability to flash the old cables to the newest firmware thanks to the read protect (if they did that). And to write a new firmware you need to erase the old one. (Similar situation if you want to flash a custom firmware on a GOTEK floppy emulator that has a similar MCU from STM.)

Keep your eyes open on other places, reviews and videos of bricked cables. Also RT forums when some dumbass asks why his cable not working anymore...

[Mario6]

I have another cable link without PCB images (STM32F415 SKU). The seller claims that this is a real hex-v2 19.6.2 EN. However, it cannot be updated "online". ($ 119)

[papuc]

Correct. That's the other one. The genetic one that is harder to find. And that's what obdcarsale got. Board is a bit different. I got sent pictures of it. No high resolution image but it's something.

[vcdss]

any hopes with this cable?
The Atmel chip is 910

https://i.ibb.co/GRGGnZn/Whats-App-Image-2019-11-06-at-10-33-52-1.jpg (https://ibb.co/GRGGnZn) https://i.ibb.co/LvbK0wS/Whats-App-Image-2019-11-06-at-10-33-52.jpg (https://ibb.co/LvbK0wS) https://i.ibb.co/vcdQQFb/hwtype.jpg (https://ibb.co/vcdQQFb)

[gini80]

no chance !

[onek24]

Where do i find the lastest firmware and loader package from k0limer?

[kaalis]

In this topic. Start reading backwards. Page by page or search for his posts.

Sent from my SM-J510FN using Tapatalk

[Jay1908]

I think we are after different things. Me personally am not looking to update the firmware or the software. Just a want an up to date offline cable. Being stuck at 19.6.x isnt that bad considering i would have a wide range of cars that i can code from 2005 to 2019. As long as the cable and software is as stable as the 15.7 it would last me a couple of years like my 15.7 cable did. Gotta find one now that actually works.

[aboyam]

hi everyone
please
i have a vcds and i want to solve this proplem with audi a4
when driver door open on the dashboard it is flash the passenger door open
how can i revers this ?
thank you

[ZIPPO4594]

any hopes with this cable?
The Atmel chip is 910

https://i.ibb.co/GRGGnZn/Whats-App-Image-2019-11-06-at-10-33-52-1.jpg (https://ibb.co/GRGGnZn) https://i.ibb.co/LvbK0wS/Whats-App-Image-2019-11-06-at-10-33-52.jpg (https://ibb.co/LvbK0wS) https://i.ibb.co/vcdQQFb/hwtype.jpg (https://ibb.co/vcdQQFb)

Eeprom is Atmel, but uP is Arm chip. upgrade is not possible.

[bg17aw]

Where do i find the lastest firmware and loader package from k0limer?
Try this page/post: https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3639906&viewfull=1#post3639906

[liviudiaconu]

Eeprom is Atmel, but uP is Arm chip. upgrade is not possible.

Which eeprom? TA6550 not eeprom.

[blackworms]

665572665573

English bad sorry Vag com 18.9 can I polish my device again? bootler: open running in v12, gives a ready error in the car does not work in the car. The 2018 USB driver looks like 2007. 18.9 I need EN full repair function and don't know if it is hwvx44 or hvw46

[alexm1]

665572665573


İngilizce kötü üzgünüm Vag com 18.9 cihazımı tekrar parlata miyim? bootler: açık v12 de çalışıyor, arabada can ready hatası veriyor arabada calışmıyor. 2018 USB sürücüsü 2007 gibi görünüyor. 18.9 TR tam onarım işlevine ihtiyacım var ve hwvx44 veya hvw46 olup olmadığı bilmiyorum
https://www.google.com/search?q=google+translate&oq=google+translate&aqs=chrome..69i57j69i65l3.6604j0j4&sourceid=chrome-mobile&ie=UTF-8

[blackworms]

665608665609

English bad sorry Vag com 18.9 can I polish my device again? bootler: open running in v12, gives a ready error in the car does not work in the car. The 2018 USB driver looks like 2007. 18.9 I need EN full repair function and don't know if it is hwvx44 or hvw46

[alexm1]

See post #9137- download zip file.
There you will find hwtype tool
Connect your vcd$ to car + your laptop
open/run hwtype and scan your tool- post here results- picture.

The picture you posted above are not clear enought to see what is writen on the pcb parts, so , read / look for Atmel Atmega 162 Au, if you find it let us know.

[blackworms]

See post #9137- download zip file.
There you will find hwtype tool
Connect your vcd$ to car + your laptop
open/run hwtype and scan your tool- post here results- picture.

The picture you posted above are not clear enought to see what is writen on the pcb parts, so , read / look for Atmel Atmega 162 Au, if you find it let us know.

665737665738665739

I wrote the individual chips because the picture is not clearly read. it doesn't work when i connect it to the car like in the picture. com does not see 1-2-3-4 ports. vagcom 18.9 EN + DE HEX-V2 - 2018 release. I have to polish it again, but I don't know how. I need all the polishing files in usb and com port files

[Xaby]

If bootloader is unlocked, download v9.2 from kolimer after that write with VAGCOM_EEWriteLang polish language, than you install vcds poland and update firmware.

[blackworms]

If bootloader is unlocked, download v9.2 from kolimer after that write with VAGCOM_EEWriteLang polish language, than you install vcds poland and update firmware.


Can you send me the files ?

665780

[rak183]

Can you send me the files ?




https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3714915&viewfull=1#post3714915

[blackworms]

https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3714915&viewfull=1#post3714915


I'm trying a Vw polo 6n. vcds 18.9 + loader v7.0 was successfully written and vcds approved the license but did not work when I installed it in the car. Will the update be the solution? raise loader 9.2

665789

[rak183]

Use loader 9.2. Y have to flash your cable. See read me file inside loader.

[blackworms]

Use loader 9.2. Y have to flash your cable. See read me file inside loader.


From the loader file you mean boom

665806

[jan4]

From the loader file you mean boom

665806




read your pm

[Col19]

Hi friends,

I see that the cable with STM32 is out but the manufacturer of this clone is as greedy as ro$$teak ;) In short, i prefer to stay with my atmega162 enough for my stuff.

Exactly i would like to ask a question to the experimented, which version is really functional with this He><V2 ? the 19.6 is not stable at home, the 18.9 is stable but as a lock, it is necessary to choose an even older version for the encodings... ?

Thanks and respect to the forum and friends such as Kolimer and all the big the sharing.

[winamax69]

Hello everybody,

Is this cable upgradeable?666752666753

Cable is blocked because of Internet connection.
C-test shows: Atmega162 Read error.

regards winamax69

[alexm1]

Yes, Will do by usb using "things" from Kolim3r zip or by usbasp.

[winamax69]

VAG-Com HWType:
VID / PID : 0403 / FA24
FT Serial : RT3S7QOI
FT Description : Ross-Tech HEX-USB
FT Chip ID : 0x503E8C25
FW Version : 1.78
HW Version : 0x44
Identification : ROSSTECH
SN : 0x00A8F2A9D716
Language : Chinese - ZHS
Bootloader : Enabled


but

I tried to write eeprom and I get this message: Writing firmware failed. Invalid bootloader?.

I think I must flash Atmega with USBASP. Am I right?

Cable has no GAL chip, but HWType shows: 0x44

How can I identify 100% is a 0x44 hardware typ?

[bajticzek]

Hello, can anyone tell me which cable should I get? Is V1 with M162 good enough? Right now I have prehistoric v11.11. It works fine, but you know, maybe a little updated version would be better. If I understand correctly, V1 doesn't support whole MQB platform, so does it mean all cars listed under wikipedia.org/wiki/Volkswagen_Group_MQB_platform (https://en.wikipedia.org/wiki/Volkswagen_Group_MQB_platform) are no go with V1?

Either way, is this version ok? https://imgur.com/9I7KOTH

Thanks for any info...

[alexm1]

VAG-Com HWType:
VID / PID : 0403 / FA24
FT Serial : RT3S7QOI
FT Description : Ross-Tech HEX-USB
FT Chip ID : 0x503E8C25
FW Version : 1.78
HW Version : 0x44
Identification : ROSSTECH
SN : 0x00A8F2A9D716
Language : Chinese - ZHS
Bootloader : Enabled


but

I tried to write eeprom and I get this message: Writing firmware failed. Invalid bootloader?.

I think I must flash Atmega with USBASP. Am I right?

Cable has no GAL chip, but HWType shows: 0x44

How can I identify 100% is a 0x44 hardware typ?Has no GAL but there is ATF(same thing).
So, if reflash by usb failed, try with usbasp.
Pay attention with fuse bits and choose 0x44 dump.

[winamax69]

Thank you, I'll try it with usbasp.

Updated:

With Usbasp I flashed Atmega then With Mprog the FTDI chip. And with Hw write the eeprom with own language file. Now work like a charm with KLo@der 9.2.

Thank you very much.

Tapatalkkal küldve az én SM-G920F eszközömről

[Zippair]

Hi,

Yesterday I tried to do something in an 2019 Octavia (is is only 2 weeks old), My cable (0x46 with 1.9.6) could do the autoscan, but it couldn't download the 09 centr. elect. admap, and the adatptation button is grey in this module (I used the 31347). It means, the V2 cable is needed for this car, or a newer software will enough for the adaptations?
Someone tried the 0x46 cable with 2019 car? what sas the result?

[safm]

For who is interested, i just received this cable https://www.aliexpress.com/item/4000122237317.html?spm=a2g0s.9042311.0.0.69184c4dC LpdvO

And it works perfectly, v1 with v2 case.

[AMDOR]

safm (https://www.digital-kaos.co.uk/forums/member.php/159930-safm) Hello friend , which versions of vcds does it contain and languages,
which version of loader does it contain. Thank you

[bg17aw]

I got one from that seller as well, works perfectly, comes with a CD with the loader, but of course you can just use any loader you want.

The bootloader is unlocked, of course.

[Daniellus]

Hi is there anybody on this forum that can help with the download link or software for the version of Vag k+can Commander in the attached picture,
667724

[ganobi]

Hi is there anybody on this forum that can help with the download link or software for the version of Vag k+can Commander in the attached picture,
667724

This is a topic about vcds, vag commander is something else.

[izeman]

May i ask anyone to confirm that this cable is NOT working. I understand that it needs ATMEL chip, which is NO installed here.

668442668443

[alexm1]

This is not v€d$ cable, probablly is Vag K.

[majidf]

I downloaded last night

Sent from my LYA-L09 using Tapatalk

What is a good interface and where can I buy one. I'm located in Europe.

[izeman]

This is not v€d$ cable, probablly is Vag K.
Thanks. I ordered the one from Aliexpress some threads above now.

[alexm1]

From Aliex.. if you are lucky, you get a working one. There is other seller (obd2cartool) from where I buy and had a good experience with it.

[Lolo4321]

Did anyone try hex can v1 on mk7 golf, does it work?

[tobyb]

Version 19.6.0 work ok with Kolimer patch.Version 19.6.1 and 19.6.2 not ok (ROD file problem).

[aj4u]

Hi

Sorry for the n00b question, I just got a A4 B8 2008. What version of VCDS/VAG Com do I need for this car?

thanks aj

[Lolo4321]

Hi

Sorry for the n00b question, I just got a A4 B8 2008. What version of VCDS/VAG Com do I need for this car?

thanks aj
Hex can v1

[zredaf]

Hi, does anyone have the software and loader for 18.9?

thanks

[aj4u]

Please can anyone recommend where to buy a hex can v1 clone which I can use to debug issues on my A4 b8 2008

I've seen one on fleabay with title :

USB VAG CAN PRO S.W Ver 5.5.1 V DIAGNOSTIC SCANNER TOOL for VW AUDI SEAT/ SKODA


Will this do the trick?


Thanks AJ

[Mario6]

aj4u (https://www.digital-kaos.co.uk/forums/member.php/5452-aj4u)

The choice is yours . Just buy both vcd$ and vcp+k.

VCD$

https://www.obd2cartool.com/index.php?main_page=advanced_search_result&search_in_description=1&zenid=p6ha6dh7md91gh1jgm4016dpr2&keyword=vcds

https://pl.aliexpress.com/store/all-wholesale-products/2411061.html?spm=a2g17.12010608.0.0.12f7530dnCfwx7

VCP+K

https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20191122004429&SearchText=vag+can+pro

[psgpol]

hi, i just bought new cable V2 from obd2cartool.com and also ISP USBASP download programmer because my old vag 15 has got disabled bootloader. I wish to fix also this cable v15 for a gift.

Could you give me some info where i should solder wires from ISP Programmer, and which software tool i should use to setup bootloader enabled (to use HW write loader)

this is info from hw type:


FT Description : Ross-Tech HEX-USB
FT Chip ID : 0x38BDD1BE
FW Version : 1.94
HW Version : 0x46
Identification : HEX-OEM
SN : 0x015FXXXXXXXXXX
Language : German - DRV
Bootloader : Disabled

this is info from C-test:


Device : 1
Description : Ross-Tech HEX-USB
VID & PID : 0x0403FA24
FT_Chip ID : 0x38BDD1BE

SW Version : 1.94
Loader ver. : 0.70, HP
Firmware : functional fake

pictures from both sides (could you mark points where to solder wires:
chip name D79F8513A

[alexm1]

Stop looking for soldering points...

Did you see Atmega 162 Au on PCB?

I think you have there a NEC cip...no dumps for it. Someone post a solution - for NEC , if you have time to search on this topic...you migth find it.
https://uploads.tapatalk-cdn.com/20191122/fa04e5ac65fc9d530c1cc28e7d91a6a1.jpg

[psgpol]

Alexm1, you're absolutely right, this is NEC (chip name D79F8513A), sh it... cable is closed for updates
this is another reason to buy cable only from obd2cartool.com

do you think i can remove this NEC and solder for example this atmel 44 leg:
https://pl.aliexpress.com/item/32786749025.html?spm=a2g0o.productlist.0.0.4016388 c7s2Qmk&algo_pvid=0cd0fe8b-03e4-4c0b-a0c0-62b25f994601&algo_expid=0cd0fe8b-03e4-4c0b-a0c0-62b25f994601-0&btsid=166a4b22-b5b5-46cd-91c4-6b63e342e0d4&ws_ab_test=searchweb0_0,searchweb201602_3,searchwe b201603_52

(https://pl.aliexpress.com/item/32809654891.html?spm=a2g0o.productlist.0.0.40c72c6 aVYhm8R&algo_pvid=17e1140a-b147-4d91-ac0e-4a5817b18ecb&algo_expid=17e1140a-b147-4d91-ac0e-4a5817b18ecb-4&btsid=3a51551a-0316-4ac5-a8ad-f6ff4715493b&ws_ab_test=searchweb0_0,searchweb201602_3,searchwe b201603_52)
maybe this could be possible but probably i will not get atmega flash file

[liviudiaconu]

Stop dreaming. Atmega162 is not equivalent with Nec D79F...
Buy another cable with Atmega162, a good one (read on this topic from where) and can make updates with known solution

[boulahya]

:applause:
Stop dreaming. Atmega162 is not equivalent with Nec D79F...
Buy another cable with Atmega162, a good one (read on this topic from where) and can make updates with known solution

[Maitreya]

Hello Friends.
I have an old USB VAG COM cable with ATMega162 and FT232RL. Firm ver 1.84 and VCDS ver 11.11.2.
I want to upgrade it for using with my new audi A3.
Before flashing I read quite a few posts and dowloaded all neccesary resouces.
First I ran the VAGCOM_HWType.exe. It reported "Interface not found". However the driver of the cable was OK because VCDS 11.11.2 worked well.
Then I tried to program the FT232 chip by writing "ftdi_mprog_RLRQ.ept" to the FT232RL. Succeeded. Then I installed the new driver successfully.
Now trying VAGCOM_HWTye.exe again and it reported:
669736

Glad to see that the boot loader was enabled but the HW version "0X46" confused me, because I learned from various places that if the pin34/35 of ATMEGA were connected to the PLD(ATF16V8), the HW version should be "0X44", which is exactly my case:
669739

Anyway I proceeded. Successfully refreshed the avr162 with one-click tool "VAGCOM_EEWriteLang.exe" —— with flash & EEPROM for "0x46" HW.
The cable seems working with 19.6.1 on my old fabia but I'm still a little worring. Does any one know if I did something wrong?

[alexm1]

If it works, be happy, d ont worry!

[dodiss]

Hello,
I upgraded my original hex-can usb to hex net pro, using ross-tech uprade option.
Old one must be destroid, but in the matter of fact, i have it.
It would be stupid to use it in laptop with internet i think, because my new one can be blocked for that "joke" :)
So its interesting now, can it be reflashed, serial number changed..in other words- can original became a clone ? Can i find right dump for it ?
Thanks.

[hid3]

I'm pretty sure they have already blacklisted it anyway.
The blacklist will be populated upon next version, as well, if you connect it to existing V(D$ or "V.exe /update" runs which is on startup, the interface will be permanently bricked

[dodiss]

Thanks. Update is asking to update, but if i will not install it and just use current one version...so it can't be blacklisted.. I think.. or am i wrong..

[Maitreya]

Yes you can if your cable was built with chip ATMEGA162.
It would be a little bit difficult if you don't have any experience in firmware upgrading or even soldering.
However the cable is dead already, why not try to do something?

Hello,
I upgraded my original hex-can usb to hex net pro, using ross-tech uprade option.
Old one must be destroid, but in the matter of fact, i have it.
It would be stupid to use it in laptop with internet i think, because my new one can be blocked for that "joke" :)
So its interesting now, can it be reflashed, serial number changed..in other words- can original became a clone ? Can i find right dump for it ?
Thanks.

[pocinas]

Hi lads.

It is someone here who use Well clone quality vcds with china vcds loader 1.1x ?

I bouht one.. all looks nice, inside as well.

I requested with seller for activation to my vcds loader and i got it.. loader is activated..

I got problem because vcds work me with FRN and ADP (FRN - think French ADP is Polish), i prefer use ENG but doesnt with Eng vcds 19.6.2... tried 19.6.1 as well.. dont recognize interface.

Seller dont replay my at the moment for my message about problem with eng version which i prefer to work and try sort out problem here, if possible.helps..

Any sugestion.

[Shanewazere]

Hello there new here anybody any experience with this cable
or can point me to a better one on obd2cartool thanks https://www.obd2cartool.com/vagcom-1962-hex-can-usb-interface-vcds-196-online-update-version-16-multilanguage-p-1263?zenid=d5suemdfb1np8sagh3pkaghhs4

[dodiss]

hi, no problem with smd soldering :) Flashing too. Never tried to read VCDS atmega, but don't think it a miracle :)

[dodiss]

Yes you can if your cable was built with chip ATMEGA162.
It would be a little bit difficult if you don't have any experience in firmware upgrading or even soldering.
However the cable is dead already, why not try to do something?

hi, no problem with smd soldering :) Flashing too. Never tried to read VCDS atmega, but don't think it a miracle :)

[Maitreya]

TRY
1. uninstall current version V(D$ and remove the directory where it was installed.
2. Download 19.6.2 from the official site and install it to your PC. During the installation the cable should NOT be connected to the USB. Do NOT to uncheck ""Run V(D$ at once" before click OK button at the last step of the installation.
3. Connect the cable to the USB port. If lucky the driver will be installed automatically. If failed to load the driver try to install it manually.
4. If the cable is identified and driven properly it should work. Google "V(D$Loader" you should find the 9.2 version. Download it and copy the file "V(D$LOADER.exe" to the directory where V(D$.EXE is located. Run the loader and try testing the cable.
5. If the cable cannot driven by the 19.6.2 driver, or the 19.6.2 software cannot identify the interface even the device is properly driven, you may need to refresh the firmware. That would be another story.

[Maitreya]

hi, no problem with smd soldering :) Flashing too. Never tried to read VCDS atmega, but don't think it a miracle :)

then it should be easy for you.
google "V(D$ loader" and follow the link "V*** Loader 9.2 Kolimer Automatic Installer", download the second link in that post, then you will have everything except the hardware.

[dodiss]

then it should be easy for you.
google "V(D$ loader" and follow the link "V*** Loader 9.2 Kolimer Automatic Installer", download the second link in that post, then you will have everything except the hardware.

Thank you :)

[Maitreya]

Besides, if the cable cannot be recognized by Windows with any version of driver (your old one or the 19.6.2 version), that means the FT232 chip was modified ("locked").
To solve this problem you need to refresh the FT232 chip.
First download the generic FT232 driver from http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.24%20WHQL%20Certified.zip. Unpack it.
Check your USB device VID & FID by:
Open the Device Manager of Windows -> right click the cable (should be ross-tech something with a yellow icon showing that the driver doesn't work) -> Properties -> "Detailed Information" Tab -> "Hardware ID"
You will find something like this:
670273

Then open the "ftdibus.inf" in the dirctory of the FTDI driver with notepad, replace all string "VID_0403&PID_6001" with what your find in the device manager (in this exapmle "VID_0403&PID_FA24").
Now manually install the driver and have windows install it from the FTDI Driver directory.
Once the driver is installed and working, you can use MPROG35 to refresh the FT232 chip:
Run Mprog;
"Read and Parse" to load current FT232 flash. "Save as" to save it as backup.
"Open" to open the flash file that will be written to the FT232. The file has .ept suffix and can be found in the "V*** Loader" package.
670275

*Use "ftdi_mprog_BMBL.ept" if your chip is FT232B* or "ftdi_mprog_RLRQ.ept" if your chip is FT232R*.
Write.
After that the generic driver would be useless.
Disconnect the cable.
Install 19.6.2.
Re-connect the cable. The USB driver should be loaded automatically.
Then you can proceed. The following procedures require a 12V DC power to the boad of the cable. Could connect +12V to the pin 1 of 7805 and zero to the head sink of the 7805.
Run "VAGCOM_HWType.exe". Press "read".
If the status of "boot loader" is "Enabled" you are lucky. Use "VAGCOM_EEWriteLang.exe" to automatically refresh the chip.
If the boot loader is disabled you will have to refresh it manually. A USBASP/ USBISP device is required - very very cheap. Follow the instructions. Be careful with the differnet board versions 0x44 or 0x46. Be careful with the fuse bits!

[Vagsura]

Hi everybody! Few days ago i received two VAG HEX-V2 units from China, to test them and start learning about Vagcom. Why i bought two? Because i knew i was going to break one of them hahaha.

And that´s why im here. I got one of them bricked, and no idea about where to start to fix it :palm2:

This is how it looks like:

https://fotos.subefotos.com/6e61b8a3e975a6edd2986f36455ce7cdo.jpg

[alexm1]

If you find on the other side the famous Atmega 162 AU...you migth have some luck and you could make it work as new ....after reflash. You better share more pics from both sides.

[Maitreya]

Hi everybody! Few days ago i received two VAG HEX-V2 units from China, to test them and start learning about Vagcom. Why i bought two? Because i knew i was going to break one of them hahaha.

And that´s why im here. I got one of them bricked, and no idea about where to start to fix it :palm2:

This is how it looks like:

https://fotos.subefotos.com/6e61b8a3e975a6edd2986f36455ce7cdo.jpg

Should have clearea pictures for both sides of the PCB to identify the chips.

[pocinas]

Hi lads.

It is someone here who use Well clone quality vcds with china vcds loader 1.1x ?

I bouht one.. all looks nice, inside as well.

I requested with seller for activation to my vcds loader and i got it.. loader is activated..

I got problem because vcds work me with FRN and ADP (FRN - think French ADP is Polish), i prefer use ENG but doesnt with Eng vcds 19.6.2... tried 19.6.1 as well.. dont recognize interface.

Seller dont replay my at the moment for my message about problem with eng version which i prefer to work and try sort out problem here, if possible.helps..

Any sugestion.Anyone can help with this?

[Maitreya]

Update: I manually flashed it with 1.96 0x44 without changing anythingelse. It ......works as well.
So it can work with both 0x44 and 0x46 firm wares......Then what's the difference?


Hello Friends.
I have an old USB VAG COM cable with ATMega162 and FT232RL. Firm ver 1.84 and VCDS ver 11.11.2.
I wanted to upgrade it for using with my new audi A3.
Before flashing I read quite a few posts and dowloaded all neccesary resouces.
First I ran the VAGCOM_HWType.exe. It reported "Interface not found". However the driver of the cable was OK because VCDS 11.11.2 worked well.
Then I tried to program the FT232 chip by writing "ftdi_mprog_RLRQ.ept" to the FT232RL. Succeeded. Then I installed the new driver successfully.
Now trying VAGCOM_HWTye.exe again and it reported:
669736

Glad to see that the boot loader was enabled but the HW version "0X46" confused me, because I learned from various places that if the pin34/35 of ATMEGA were connected to the PLD(ATF16V8), the HW version should be "0X44", which is exactly my case:
669739

Anyway I proceeded. Successfully refreshed the avr162 with one-click tool "VAGCOM_EEWriteLang.exe" —— with flash & EEPROM for "0x46" HW.
The cable seems working with 19.6.1 on my old fabia but I'm still a little worring. Does any one know if I did something wrong?

[TESTASTRETTA]

does anybody try HEX V2 from www.obd2cartool.com (https://www.obd2cartool.com/index.php?main_page=advanced_search_result&search_in_description=1&zenid=p6ha6dh7md91gh1jgm4016dpr2&keyword=vcds) ? is it real HEX V2? thx

[papuc]

does anybody try HEX V2 from www.obd2cartool.com (https://www.obd2cartool.com/index.php?main_page=advanced_search_result&search_in_description=1&zenid=p6ha6dh7md91gh1jgm4016dpr2&keyword=vcds) ? is it real HEX V2? thx
Seems like they have now the STM32F415 variant now as well at the low low price of $119.99. They only had 5 and someone bought one from Belgium two days ago. They show PCB so pretty sure that's HecksV2 clone.

Edit: And seems like there's another listing for $109.99 there too.

[grantius]

I have a great working VAGCAN Pro cable with a FTDL 245R - is there any version of VCDS that'll work with this?

[Maitreya]

Anyone can help with this?

Would you please post a snapshot of the "Device Manager" page of your VAG-COM device like this:
670873

[Maitreya]

Should not be. Seems like a V2 case with V1 core.


does anybody try HEX V2 from www.obd2cartool.com (https://www.obd2cartool.com/index.php?main_page=advanced_search_result&search_in_description=1&zenid=p6ha6dh7md91gh1jgm4016dpr2&keyword=vcds) ? is it real HEX V2? thx

[papuc]

Should not be. Seems like a V2 case with V1 core.
Check again. I see STM32F415. That's not Atmel. They have PCB shots in their description. Pretty easy to spot. If the price is high you know it's the right one. Click the his link and try to spot the real V2 clone.

[Maitreya]

Yes I checked there are some likely V2 clone. Some sellers show the pictures of the PCB or the snapshot of software diagnostic result. 4-5 times the price of V1. interesting.


Check again. I see STM32F415. That's not Atmel. They have PCB shots in their description. Pretty easy to spot. If the price is high you know it's the right one. Click the his link and try to spot the real V2 clone.

[Lolo4321]

obd2cartool is just a re-seller like many other stores. Im not sure if they claim to be 1:1 v2 why didn't they came here to advertise it?

[szilagyilajos]

Hi,

Anyone can help for me Loader 1.2 activation?

The seller does not respond :( :( :(

Thanks 🙏

[rak183]

If y have atmega chip flash your interface with kolimer ...

[obd2cartool]

Hi,

Anyone can help for me Loader 1.2 activation?

The seller does not respond :( :( :(
Hi, your loader too old, let your seller send the newer loader to you

[obd2cartool]

I got problem because vcds work me with FRN and ADP (FRN - think French ADP is Polish), i prefer use ENG but doesnt with Eng vcds 19.6.2... tried 19.6.1 as well.. dont recognize interface.
His PC os may be the 64bits, when installing vcds choose option install 32bits to 64bits.

[obd2cartool]

obd2cartool is just a re-seller like many other stores. Im not sure if they claim to be 1:1 v2 why didn't they came here to advertise it?
Hi V2 is advertise will be easily blocked the store links

[Tib82]

I got a cable from a guy who took down all USB cable wires from PCB (I don't know how). He or somebody else tried to find the right wire order but they made an ugly solderint surface. Luckily the PCB pads are silll good enough.
I searched the same PCB (https://forums.ross-tech.com/showthread.php?3549-Hex-Can-USB-cable-not-being-seen-on-Win-7-or-Win-8-1-machines&p=36117&viewfull=1#post36117) to check the wiring but with the same wire order even the Windows cannot recognise the USB device. No "ding-dong" sound on plug in the USB port. Is anybody knows what should be problem or the right USB wiring order?

672053672054

[poilodo]

no matter what form the pcb.
The operation of the interfaces is the same.
The connection of the USB is identical.

[Tib82]

... The connection of the USB is identical.
I did a quick search and I found 3 types. Basically the clones have the same wiring, but now I'm asking for the genuine.
672092

[alexm1]

Logic guidance:
1.See picture and you have a point where to start.
2. Start with BLACK wire-
Use a multimeter to check continuity from midlle leg of the LM7805 -voltage regulator- to one of 4 pads- solder Black wire there.
Black and Red should be left/rigth and Green and White in the midlle.
So, after you find the Black pad put Red on the oposite pad, " play " with Green and white.
https://uploads.tapatalk-cdn.com/20191203/d4ed977cc41c61731f6335f99c7bb0d7.jpg

[FriskyDingo]

Can vag-k+can cable be converted to vcds cable?

[Maitreya]

Let me tell you my experience. I have a cable whose PCB and the layout of all components look identical to those of one board found on the internet. There are 10 pads on the end of the PCB for USB (4 pads), ISP (4pads), and 2 extra ones. However the USB pads are oriented in totally opposite way for 2 boards, and the extra 2 pads on my board are GND, but on the other board they are VCC to the chips other than FT232 (FT232 is powered by USB port)!
As was described in #9213, if you are sure which 4 pads are for USB, first please find the GND with a multimeter. The GND pad (for the black wire) shall be shorted to the heat sink of the 7805 regulator. Then, in principle, the neighboring one is green (D+), then white (D-), then red (USB VCC).
The most reliable way is to check the connectivities between these pads and the FT232 chip. The one who connected to pin8 (USB DM) of FT232 should be white and pin7 (USB DP) should be green. The resistance between the pad to the pin may not be zero but should be a quite limited number:
672114

However I cannot locate the FT232 on your board.....

[Maitreya]

OK done with it. Take a look at the following picture. It's the upper right corner of your side-a.jpg. The QFP32 chip is FT232.
672117

The pin8 is linked to USB D- via a 27R risistor and pin7 to D+ as well. So your white and green wires are in correct positions.
Check the pad in the red circle. I highly suspect that it should be USB VCC (red wire) but the pad was destroyed by bad soldering. Check if it is shorten to pin3 of the FT232.
The pad currently soldered to red wire is supposed to be GND and should be soldered to black wire. However before operation check the connection between it and the pin9 of the FT232 or the heatsink of the 7805.
Anyway by checking the connectivities you can easily find the proper connection way. It should work if none of the components was destroyed by mistakenly applied voltage. Good luck.



I got a cable from a guy who took down all USB cable wires from PCB (I don't know how). He or somebody else tried to find the right wire order but they made an ugly solderint surface. Luckily the PCB pads are silll good enough.
I searched the same PCB (https://forums.ross-tech.com/showthread.php?3549-Hex-Can-USB-cable-not-being-seen-on-Win-7-or-Win-8-1-machines&p=36117&viewfull=1#post36117) to check the wiring but with the same wire order even the Windows cannot recognise the USB device. No "ding-dong" sound on plug in the USB port. Is anybody knows what should be problem or the right USB wiring order?

672053672054

[Tib82]

... The pin8 is linked to USB D- via a 27R risistor and pin7 to D+ as well. So your white and green wires are in correct positions.
Check the pad in the red circle. I highly suspect that it should be USB VCC (red wire) but the pad was destroyed by bad soldering. Check if it is shorten to pin3 of the FT232.
The pad currently soldered to red wire is supposed to be GND and should be soldered to black wire. However before operation check the connection between it and the pin9 of the FT232 or the heatsink of the 7805. ...

I cleaned the old wirings and the pads are not in that good condition than I thought. Hopefully they are still work.
I checked the left connection point (where Blask is soldered) and it shorted with the 7805 heatsink. So it looks OK.
If the green and white cables are in a good position, the wiring should be good.

Here is a pic from the RT forum. The wiring is the same as "mine". It has a 5th hole what is not a pad :)
672128

I think the problem should be the bad quality of soldering or partly damaged pads or previous user mistake with a bad connection (and with it destroyed component).

[Maitreya]

Yes I carefully viewed the picture again and found that the "hole" on the upper right edge must not be a pad because in the oppsite direction there is another one obviously not a pad.
That means the positions of your wires are correct. Clean & check the soldering, then good luck!
This board seems the "official" version.


I cleaned the old wirings and the pads are not in that good condition than I thought. Hopefully they are still work.
I checked the left connection point (where Blask is soldered) and it shorted with the 7805 heatsink. So it looks OK.
If the green and white cables are in a good position, the wiring should be good.

Here is a pic from the RT forum. The wiring is the same as "mine". It has a 5th hole what is not a pad :)
672128

I think the problem should be the bad quality of soldering or partly damaged pads or previous user mistake with a bad connection (and with it destroyed component).

[mahadeva]

hi. i have vcds v2 cable from aliexpress version 19.6.1 (kolimer vcdsloader 9.2). can i update software to 19.6.2 and use kolimer loader without problem? :D sorry for newbie question

[Maitreya]

Just do it.
and..... if you install different version softwares to different directories and copy the loder to each directory, you can run different version softwares on one computer.
On my PC there are 17.1.3, 17.8, 18.9, 19.6.1. Generally new version supports new model cars better, but sometimes old ones are better for old cars.

[mahadeva]

Just do it.
and..... if you install different version softwares to different directories and copy the loder to each directory, you can run different version softwares on one computer.
On my PC there are 17.1.3, 17.8, 18.9, 19.6.1. Generally new version supports new model cars better, but sometimes old ones are better for old cars.

I just updated my vcds v2 from 19.6.1 to 19.6.2 and used vcdsloader 9.2 its working perfectly :o thanks..

Can i update vcds v1 cable version 18.9.0 to newer version? Should i update firmware too? Thanks again

[kaalis]

Yes, do both.

Sent from my SM-J510FN using Tapatalk

[Maitreya]

Not necessarily. From 18.x (and even earlier versions) to 19.8.x the V¢D$ works with V1 cables with firmware 1.96 only. That means your cable has the most up-to-date version firmware, otherwise it wont work.

I just updated my vcds v2 from 19.6.1 to 19.6.2 and used vcdsloader 9.2 its working perfectly :o thanks..

Can i update vcds v1 cable version 18.9.0 to newer version? Should i update firmware too? Thanks again

[mahadeva]

Not necessarily. From 18.x (and even earlier versions) to 19.8.x the V¢D$ works with V1 cables with firmware 1.96 only. That means your cable has the most up-to-date version firmware, otherwise it wont work.

thanks for answar.. so i need to update firmware with eeprom right? :)

[Maitreya]

NO you don't need to do so.
Your cable has definately the most up-to-date firmware version, which is 1.96. For both the program and eeprom.
The number "1.96" has nothing to do with the recent VCD$ version 19.6.2 - they just look alike. As far as I know, in the past 8 years there were only 3 firmware versions released, 1.84, 1.92 then 1.96. However there were tens of VCD$ software versions from 11.xx.x to 19.xx.x. The version number of VCD$ version denots the year in which the sofware was released and upgrade turns in that year.
The firmware 1.96 was released a acouple of years ago and from that time on, VCD$ new versions work with 1.96 only. So any cable works with 19.xx, 18.xx, 17.xx ... must has the most up-to-date firmware.
Nobody knows when the next version firmware will be released - probably not forever because they are promoting their HEX-V2 now. V1 cables gonna have less and less functions and then die on one day. Sadly but true.


thanks for answar.. so i need to update firmware with eeprom right? :)

[hid3]

Nobody knows when the next version firmware will be released - probably not forever because they are promoting their HEX-V2 now. V1 cables gonna have less and less functions and then die on one day. Sadly but true.

Never.
They are now artificially limiting the HEX+CAN functionality ("incompatible vehicle, please upgrade", etc).
Besides, there is no flash space in AT162 for firmware updates.

[Maitreya]

Thank you. I guess so, too.
Never.
They are now artificially limiting the HEX+CAN functionality ("incompatible vehicle, please upgrade", etc).
Besides, there is no flash space in AT162 for firmware updates.

[alexm1]

Can anyone share a link for downloading 19.6.x German version that can work with Kokimer.s dumps?
I found and tried a few earlier links (innthe forum) but all are "dead".

[jan4]

https://www.auto-intern.de/downloads/diagnose-software/

https://www.mft-shop.de/ross-tech-vcds/vcds-download/

https://vcdspro.de/downloads/

[TESTASTRETTA]

So nobody bought real function hex V2 from china?

[jan4]

at least not a forum member ……………..so far

[Fabio89]

Any chances to next VCDSLoader works in MQB-A0 models? :hmmmm2:

[Lolo4321]

For now uds noncommunication/ not suported

[Maitreya]

If you your VCDS and cable could perform normal connection and scanning/ reading, but encountered

674317

while traing to code or adapt somthing, and got a failure feedback like

674318

after clicking the OK button, please lift the hood of the car and then it will work.
This kept bothering me a couple of days until yesterday I tried the 19.6.2 which came with a new feature that a warning message will jump if the software suspects that there is a diagnostic firwall activated:
674319

With the old 18.9 ZHS version there was no warning so I didn't know what happened when I could not access the coding and adapting. It was very strange that at the beginning (brand new audi A3) I could do without lifting the hood but since last weekend I could not until I found the way on yesterday evening.

[Maitreya]

Not sure what you meant but working or not working with certain platform is related to the cable and the VCD$ version. Nothing to do with the Loader.

Any chances to next VCDSLoader works in MQB-A0 models? :hmmmm2:

[navin]

I received my hex v2 from ali and its on fw: 0.256. obdcarsale I saw yours is fw: 0.251.

https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3704910&viewfull=1#post3704910

[TESTASTRETTA]

And is it real v2? Can you check vcds cable info to confirm its V2?

[MiloszT]

I need to check HEX-V2
I can't download the C-Test.rar file from the site

https://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=601722&d=1551937539

Anyone give an external file link?
Thanks

[hid3]

HW_Info tool has got all the functionality you need

[Botond]

Hello, can anyone share with me a link to hex v2 18.9 en?
Bought today, but cd don't working :/

[MiloszT]

All versions in English

https://my.pcloud.com/publink/show?code=MvPitalK

[navin]

Yes its the closest to the real one.
674803

674804


674805

And is it real v2? Can you check vcds cable info to confirm its V2?

[morofsky]

friend of mine left me a cable he said that his cable used to work but now the interface is not being found. the device driver gives code 10 and i cant find the device neither under MProg or VAGCOM_EEWriteLang, any advices what can i do to revive it? it is china replica with ftdi ft232rq and atmel mega 162

[alexm1]

Double check usb cable+soldering pads on the pcb. But most of the cases FTDI is pobably deffective.

[Maitreya]

Is there any software package that came with the cable? You should try that driver first.

friend of mine left me a cable he said that his cable used to work but now the interface is not being found. the device driver gives code 10 and i cant find the device neither under MProg or VAGCOM_EEWriteLang, any advices what can i do to revive it? it is china replica with ftdi ft232rq and atmel mega 162

[AlexKudry]

hallo, can I have the Link from HEX V2? Thanks

[quadral]

Maybe here

https://www.obd2cartool.com/diy-vag-com-1962-hex-v2-interface-mqb-hex-v2-unlimited-vin-diagnostic-cable-for-vw-audi-seat-skoda-free-shipping-p-1388

i am waiting for an special offer to dk-member.

[tk500]

Already is blocked.

[kaalis]

19.6.2 ZHS and ZHT just released.

[Zippair]

https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3743045&viewfull=1#post3743045

Before opening the hood, the adaptation button was grey in your vcds? We have a new Skoda Octavia, and the adaptation button is grey in the 09 cent. Elect, (after i wrote the security acces code)

[hid3]

Does anyone have the "HEX-V2" interface which is faulty due to "CAN not ready" issue? Please PM me.

[kashelis]

Hi. Can anyone share vcds 18.9 ENG?

[Alesk]

Hi. Can anyone share vcds 18.9 ENG?You can try!
Best regards 676316

[Maitreya]

No nothing was grey. Still I could adapt or code but the application will be refused at the final step.
Besides, it seems that with 19.6 the adaptation of central elec was grey even after entering the correct access code . I'm not sure (poor memory) but that might be the reason why I always use 18.9.

https://www.digital-kaos.co.uk/forums/showthread.php/99750-VAG-COM-VCDS-EVERYTHING?p=3743045&viewfull=1#post3743045

Before opening the hood, the adaptation button was grey in your vcds? We have a new Skoda Octavia, and the adaptation button is grey in the 09 cent. Elect, (after i wrote the security acces code)