VAG-COM/VCDS EVERYTHING

[apophizz]

it is so. the person I bought the cable said it's from VAG Diagnostics Ltd - VCDS Vag-Com 908, 912, & 10.6 Cables (http://www.vag-diagnostics.com). so I asked the vendor of vag-diagnostics that the cable 908 also works with the VCDS912 version because something read about this on his website. The seller told me that it should work, otherwise I would have never tried.

I've read something in the forum, unfortunately I have not found any instructions as it works with a 908 cable, only for the 805 and older

regards

[bibkare]

it is so. the person I bought the cable said it's from VAG Diagnostics Ltd - VCDS Vag-Com 908, 912, & 10.6 Cables (http://www.vag-diagnostics.com). so I asked the vendor of vag-diagnostics that the cable 908 also works with the VCDS912 version because something read about this on his website. The seller told me that it should work, otherwise I would have never tried.

I've read something in the forum, unfortunately I have not found any instructions as it works with a 908 cable, only for the 805 and older

regards

Seller will tell you what you need to hear, everything is explained for version 908 actually it's the same procedure for 805 except version of dump, if you really wanna cable fixed you must read this thread and post interface pics

[apophizz]

here some pictures of my 908 Cable...

http://91410.webhosting35.1blu.de/teamvw/bilder/VAG908interface/IMG_5669.JPG

http://91410.webhosting35.1blu.de/teamvw/bilder/VAG908interface/IMG_5668.JPG

http://91410.webhosting35.1blu.de/teamvw/bilder/VAG908interface/IMG_0117.JPG

http://91410.webhosting35.1blu.de/teamvw/bilder/VAG908interface/IMG_0115.JPG

http://91410.webhosting35.1blu.de/teamvw/bilder/VAG908interface/IMG_0114.JPG

[paro44]

@apophizz:

You have ft232rl inside, so your solution is here: (http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/)
Follow the steps and your interface should work again.

[bibkare]

@ apophizz (http://www.digital-kaos.co.uk/forums/members/236102-apophizz/) really nice taken pics, this should be exapmle for all others, unfortunately you have the worst possible hardware, much more complicated to fix than version based on ft232bl, like paro44 said follow those instructions

[kevinb2u]

@dariusddj-

Not sure why I could not click thanks, so THANKS! Will try it this weekend.

What about the GAL chip? In "Final solution for Chinese VAGCOM interfaces with protection chip and FT232R", shows extra wiring and flashing the GAL chip, different than this tutorial.. Thanks again

[bibkare]

@dariusddj-

What about the GAL chip? In "Final solution for Chinese VAGCOM interfaces with protection chip and FT232R", shows extra wiring and flashing the GAL chip, different than this tutorial.. Thanks again

Yes it's different because hardware based on ft232rl requires more modification than interfaces with ft232bl

[kevinb2u]

Yes it's different because hardware based on ft232rl requires more modification than interfaces with ft232bl

Just looked again, mine is RL, housing marked:

VAG912
Dual-K & CAN <-> USB
VAG/ISO Interface

Am I better off with the extra work to mod this one, or try to get a BL (Older?).

And--I would unsolder the GAL and/or the ATMEGA to flash externally? The "Final Solution" says to flash, but not how. I do have Willem programmer and adapters, and pretty good at SMDs, but have yet to try it. Thanks again

[lukisio]

Hellow. i have a problem, becouse my vag1062 not read mensuring block. Block 1.1 ok, but 1.2, 1.3,1.4 is N/A? I have a full version. v200. Please help me. HEX CAN v1.83

[mattydr67]

Just looked again, mine is RL, housing marked:

VAG912
Dual-K & CAN <-> USB
VAG/ISO Interface

Am I better off with the extra work to mod this one, or try to get a BL (Older?).

And--I would unsolder the GAL and/or the ATMEGA to flash externally? The "Final Solution" says to flash, but not how. I do have Willem programmer and adapters, and pretty good at SMDs, but have yet to try it. Thanks again

Gal you need to unsolder and reflah it extarnally but Atmega you do not.
In the tutorial you can find every dump you need to do this job.
Good luck.

[mattydr67]

Hellow. i have a problem, becouse my vag1062 not read mensuring block. Block 1.1 ok, but 1.2, 1.3,1.4 is N/A? I have a full version. v200. Please help me. HEX CAN v1.83

You don't have a real original softwear you have a cracked chinese softwear and this is the problem. It cannot show everything.
Sorry
Good luck

[kevinb2u]

Thanks very much, that clears up a lot...

[tk500]

Hellow. i have a problem, becouse my vag1062 not read mensuring block. Block 1.1 ok, but 1.2, 1.3,1.4 is N/A? I have a full version. v200. Please help me. HEX CAN v1.83

And that is not all, DTC is wrong decoded

[mishu_b]

And--I would unsolder the GAL and/or the ATMEGA to flash externally? The "Final Solution" says to flash, but not how. I do have Willem programmer and adapters, and pretty good at SMDs, but have yet to try it. Thanks again

you can flash the Atmega with PonyProg software via Parallel port ...

all the best
mishu

[kevinb2u]

you can flash the Atmega with PonyProg software via Parallel port ...

all the best
mishu

Thanks, What do you guys use for hook-up wire from LPT cable to the PCB? Thinking a strand of copper might work ok, also have steel MIG wire, probably would not take solder well. Something better at Radio Shack I should get?

[zmeulzmeilor]

Where can i find faults codes for skoda?

[PEDRO4053]

Hello my cable apare?e USB\VID_0403&PID_FA20\RT000001 the one what would this last one be I number RT\000001?
Pedro
I wander in the vidpidfix
Hello


Am I with a problem when I try to use the vidpidfix him of the mistake?
http://images.orkut.com/orkut/photos/OgAAACt0-JRo_NzoPB_Cu7j11JQ8gszUjrXIwSCEUbIkhNszFxo9HMh3uVr fZ6K0jFhPB80qnKytYFwdSRxDHWWs21gAm1T1UHK_olyZWvnN_ P2lQ-havqyTnGNi.jpg
http://images.orkut.com/orkut/photos/OgAAAMQLnRzvWHkeu5iIoyzsTEY7ZTFTd5HR5nCc72dH-SNuZXwG7HpNJuf2HKSYJotA_BqsNZ7RmSdDtUpHedKuOeYAm1T 1UHD4IP0E9NP6e7fwKRW3cuj1I9_k.jpg
thank you
Pedro

[max4ever]

Select RT0000001 , click "Open" and go "Write Default EE Data"

[apophizz]

@apophizz:

You have ft232rl inside, so your solution is here: (http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/)
Follow the steps and your interface should work again.


is there a difference between FTDI 232 R und the RL Version? or its the same?

a friend of mine has a (i don't know the correct word in english EEPROM Programmer/Burner) who i can write the EEPROM on it, i hope you know what i mean...

is it easier to rewrite my cable with this? or should i do it with the tutorial i get from paro44?

regards

[superjim02]

hello
i'm new user and i want reprogramm my vag-com but i can-t dowload the tutorial.rar : i have not permission.

Why, ? can you help me please ?

[superjim02]

sorry,

now it's good : i have posted One message and its good

[PEDRO4053]

After made the whole work following tutorial ,quando it blinked the green led I removed and I connected it was not more recognized by the windows.When do I connect in the car the green led he/she lights if it connects in the computer the red led he/she lights I must have made something wrong more with I can repair?

Now my cable this killed somebody it can me to help ,como I can do for the windows to recognize him for me to try to carry the draiver.


Thank you
Pedro

[kodo28]

Found the solution for my problem, it's a software problem, here is the right setup for 10.6.2:

http://rapidshare.com/files/445430383/VCDS-Release-10.6.2-Installer.exe

Source:

Google Translate (http://translate.google.com/translate?hl=en&sl=it&tl=en&u=http%3A%2F%2Fwww.vwitalia.it%2Fforum%2Ff141%2Fva g-com-10-6-che-non-mi-fa-salvare-le-codifiche-9783-4.html)

Hello spongemak,

You did a great job to find this working .exe

Really a big thank you, cable 10.6.2 working 100%
and saving long coding now ;))

:goodpost:

[Carlos_]

Hello spongemak,

You did a great job to find this working .exe

Really a big thank you, cable 10.6.2 working 100%
and saving long coding now ;))

:goodpost:

Indeed it was a great job this finding :)

But i have a little problem, i can?t run the exe. the program has 2 exe, one of them is the one that the shortcut on desktop leads to, and when i click it (the shortcut or the exe itself), nothing happens!

I've tried on 2 different computers (Windows 7 32 and 64bit) and the result is the same.

Can someone give a suggestion?

Thanks in advance

[jo?o antonio]

H? friend , I installed the program VCDS 10.6.2 in the PC windows XP 32bit , it is full working fine now !!!!! , thanks

My cable is VCDS-10.6.2 with FW 1.83 - drive R-T USB direct , version 2.6.2.0 , USB\VID_0403 PID_FA24\RT000001

But , what is the correct icon to start ?

VCDS.EXE
or
VAG1062.EXE

????????????

Thank you for all DK members.

[max4ever]

VCDS.EXE is version 10.6.3 kind of!?
VAG1062.EXE is version 10.6.2!Sure!

[Volki]

Hello,

Please help: I have a Vag-com 908 china cable. Unfortunately I had to reinstall my operating system (win7). Now the cable doesn't want to work. My previous system was also win7 where it's worked. With the china 908.1 software I get time out error message always, and the software is not starting.

With the 908.0 version the software is starting but I get "not plugged into car" message however it's plugged. This also happening with the 812.4 version.

I have never used or installed higher than 908 version.

When I plug it in the car I see green LED light.

What is the problem?

Thanks

[s3mick]

Hi all, tried reflashing the atmega chip again, the first time was ok but still had shareware, but now ponyprog cannot access it, also the led is not working, does any one know if i have blown/shorted some thing, i can see the cable when pluged into the usb port with mprog and vidpidfix, thanks

[s3mick]

just tried again and the cable works on the car but not when pluged into the lpt port, light is off but comes on when unpluged, think its a problem with the earth wire on the atmega chip? anyway tried scan on car but only runs part through then says requires registerd cable and in the info part it says requires full scan or something to activate, tried several times but no luck, then asked for drivers again and now wont find cable in windows xp, any help please. thanks mick

[s3mick]

just like to add not connected to intenet when running vcd 805.1 if this makes ant differance

[andye26]

Hi
Lost use of my vag com lead a couple of days ago due to running updated software. Was working with VCDS 10.6.0 with firmware 1.81, Will UPGRATE FIRMWARE 908.rar (http://www.digital-kaos.co.uk/forums/attachments/f152/51966d1298619704-vag-com-vcds-everything-upgrate-firmware-908.rar) return it to its original state or will I have to use different software and drivers.
Could I also flash it to version 805 if I wanted or is it hardware dependant
I also notice in the 908 firmware there is a modified eprom file should I use this or original?

Thanks
Andy

PS my hardware no longer knows when it is plugged into the car but updated software tried to upgrade my firmware to 1.83, Could this cause it to not know if its connected to the car?

[angelx431]

Hello,

Please help: I have a Vag-com 908 china cable. Unfortunately I had to reinstall my operating system (win7). Now the cable doesn't want to work. My previous system was also win7 where it's worked. With the china 908.1 software I get time out error message always, and the software is not starting.

With the 908.0 version the software is starting but I get "not plugged into car" message however it's plugged. This also happening with the 812.4 version.

I have never used or installed higher than 908 version.

When I plug it in the car I see green LED light.

What is the problem?

Thanks
Use VCDS_908.0_mod

[kaosdigital]

Can anyone PM me where and what kind of interface to buy for this software post #1274
http://www.digital-kaos.co.uk/forums/redirect-to/?redirect=http%3A%2F%2Frapidshare.com%2Ffiles%2F44 5430383%2FVCDS-Release-10.6.2-Installer.exeplease? Thanks.

[jo?o antonio]

H? friend , in Brazil !!!!!

Scanner Automotivo Vag-Com 10.6.2 VW Audi - Pronta entrega!! - R$ 198.00 em MercadoLivre (http://produto.mercadolivre.com.br/MLB-173557681-scanner-automotivo-vag-com-1062-vw-audi-pronta-entrega-_JM)

Thanks.

[apophizz]

hiho, on page 84 you can see mine pictures of 908 interface with the FTDI232RL chip and with the instructions "http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908- to flash FT232R 160 237 / " (http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/)i made it to flash my FTDI chip, and now is also recognized correctly. Unfortunately, now I get always the message "interface not plugged into car" I think I have now the ATMEGA chip to flash with PonyProg, is that correct? my problem is, I can't open PonyProg because the DIPortIO.dll is missing ... what can I do?

regards

[dariusddj]

i have usb-serial adapter for programing atmega and takes me 4 hours for programing and verifing. it is normal?

[dado76]

It should be less then 2 min job (only programing Atmega).

Regards, Davorin

[dariusddj]

what is the problem? usb-serial adapter or avr programer?

[andye26]

In answer to my own question above
Used modified eprom file and all went well
Unit now knows when ignition is on and working as it was.
I used an external usb programer for the atmel without any problems (Smart Pro X5) Using the 4 wire ICP connector

Regards
ANdy

[KenshinPT]

what is the problem? usb-serial adapter or avr programer?

I bet in the USB-SERIAL Adaptor.

Usually they never work for this kind of applications: uC programmers, programmable automation controller...

You can try a PCMCIA or ExpressCard adaptor:

For old laptops with PCMCIA:
PCMCIA to RS-232 Serial DB9 CardBus Adapter Card Laptop - eBay (item 370481493060 end time Mar-06-11 02:43:56 PST) (http://cgi.ebay.com/PCMCIA-RS-232-Serial-DB9-CardBus-Adapter-Card-Laptop-/370481493060?pt=LH_DefaultDomain_0&hash=item56426af444)

For new laptops with ExpressCard:
*RS-232 Serial Port Express Card ExpressCard Adapter - eBay (item 230513418951 end time Mar-17-11 01:51:53 PDT) (http://cgi.ebay.com/RS-232-Serial-Port-Express-Card-ExpressCard-Adapter-/230513418951?pt=LH_DefaultDomain_0&hash=item35ababa2c7)

USB<->RS232 adaptors emulates a COM port and sometimes the emulation won't work for some devices (programmers and PLCs)

Those PCMCIA or ExpressCard adaptors add a physical COM port to your laptop.

[dariusddj]

tanks
is working but i need 4 hours to program atmega
that's it. i have all the time in the word :)

[rsibiza]

tanks
is working but i need 4 hours to program atmega
that's it. i have all the time in the word :)


Youre right..but if u try different dumps...you need lot patience...

Try get USBASP Programmer...less than 5 euro an worth it...really...

[dariusddj]

work with ponyprog?

[apophizz]

now i have downloaded a new version of ponyprog and this i can open it :)

so i have flash the FTDI 232RL and this work correctly now, but at now i get always the message "not plugged into car"

on the final solution for my cable 232RL http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/

i should reflash my Atmega 162, but the are no tutorial on this solution...

is it the same process of the 805cable? like this http://www.digital-kaos.co.uk/forums/attachments/f152/31554d1284471406-vag-com-vcds-everything-tutorial.rar

thanks

regards

[kevinb2u]

now i have downloaded a new version of ponyprog and this i can open it :)

so i have flash the FTDI 232RL and this work correctly now, but at now i get always the message "not plugged into car"

on the final solution for my cable 232RL http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/

i should reflash my Atmega 162, but the are no tutorial on this solution...

is it the same process of the 805cable? like this http://www.digital-kaos.co.uk/forums/attachments/f152/31554d1284471406-vag-com-vcds-everything-tutorial.rar

thanks

regards


I'm stuck on the GAL chip that has to be (?) flashed with 232RL. I cannot find in PonyProg or WIllem device type. I have PLCC 20 adapter, but don't see how to proceed.

Also started solder tiny wires onto ATMEGA as in tutorial, now that's a tough one, and I do have decent equipment. Think I'll try off board, I have an adapter with new ATMEGA soldered in. If it doesn'ty work out the whole mess is going in the trash.

Again if anyone wants to fix this for me, I will gladly pay. EIther that or spring for the original, but I don't work on many VWs.

Thanks

[viercha]

Hello spongemak,

You did a great job to find this working .exe

Really a big thank you, cable 10.6.2 working 100%
and saving long coding now ;))

:goodpost:

This will work with FT232BL?

Thanks

[apophizz]

now i have downloaded a new version of ponyprog and this i can open it :)

so i have flash the FTDI 232RL and this work correctly now, but at now i get always the message "not plugged into car"

on the final solution for my cable 232RL http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/

i should reflash my Atmega 162, but the are no tutorial on this solution...

is it the same process of the 805cable? like this http://www.digital-kaos.co.uk/forums/attachments/f152/31554d1284471406-vag-com-vcds-everything-tutorial.rar

thanks

regards



i have one more question, how i can re-flash the gal chip? i found nothing about this :(

regards

[kevinb2u]

i have one more question, how i can re-flash the gal chip? i found nothing about this :(

regards


That's also part of my question above. Hopefully someone can enlighten us..

[kevinb2u]

This will work with FT232BL?

Thanks

Not for sure, but from what I've been reading here, may be better to stick with 908, you might need 10.6 interface ?

[Kazan]

Have somebody 10.6 RUS?

[newmancp]

This is all making an interesting read. Might try it myself.

Cheers.

[rsibiza]

now i have downloaded a new version of ponyprog and this i can open it :)

so i have flash the FTDI 232RL and this work correctly now, but at now i get always the message "not plugged into car"

on the final solution for my cable 232RL http://www.digital-kaos.co.uk/forums/f152/solution-clone-vcds-908-ft232r-160237/

i should reflash my Atmega 162, but the are no tutorial on this solution...

is it the same process of the 805cable? like this http://www.digital-kaos.co.uk/forums/attachments/f152/31554d1284471406-vag-com-vcds-everything-tutorial.rar

thanks

regards



Here you go:

http://www.digital-kaos.co.uk/forums/f154/updating-atmega162-vcds-other-interfaces-166596/#post806195

[rsibiza]

i have one more question, how i can re-flash the gal chip? i found nothing about this :(

regards


You need an PLCC20 to DIL converter and paralel programmer...Nothing more:driver:

[mishu_b]

...

Here you will find all you need to re-fresh GAL.
the easiest way that I found

all the best!

[apophizz]

hey everybody, there is great news, my VAG908 works perfectly again.

my friend whom I bought the cable that had the original software start it and after a few times, came the message "fix cable?" he made it and since it runs and runs it ... I'm so happy!

Thanks to all and DigitalKoas forum is a great forum

"Never changing a runnig system"

With these words, does it well

Regards

[kevinb2u]

You need an PLCC20 to DIL converter and paralel programmer...Nothing more:driver:

Thanks, I do have PLCC20 adapter that fits ZIF socket on programmer. What is DIL? What kind of chip to select with programmer s/w? Sorry for stupid questions, just beginning to try understand flashing.

[mishu_b]

...
DIL = Dual in Line (the chip has the pins on two sides e.g left and right) atb

[cniky]

...

Here you will find all you need to re-fresh GAL.
the easiest way that I found

all the best!

Play with that, cry later. GALS are quite sensitive and must keep specific voltage for different types. 12V not work for all, also direct connection of IC in LPT is a `dream` :)
Don`t recommended that , build "GalBlast" complete version, or buy an cheap universal programmer. Chinese people lunch on the market in last mounts lots of them on affordable price.

[SmrekcPRO]

To Carlos_: do you have any antivirus software installed? Microsoft security essentials for example? If yes, disable real time checking...

Br

[Carlos_]

To Carlos_: do you have any antivirus software installed? Microsoft security essentials for example? If yes, disable real time checking...

Br

Hi,

i have norton internet security, and when i first downloaded the vcds 10.6.2, it identified as a virus (or trojan, or whatever...) so i downloaded again with real time checking disabled but even so, the vcds is still not workin, i believe that norton blacklisted the file and/or the url... i'll try to download it from another computer, because i tried to unblacklist it but i couldn't find out how to do it.

Thanks for suggestion :)

[mishu_b]

Play with that, cry later. GALS are quite sensitive and must keep specific voltage for different types. 12V not work for all, also direct connection of IC in LPT is a `dream` :)
Don`t recommended that , build "GalBlast" complete version, or buy an cheap universal programmer. Chinese people lunch on the market in last mounts lots of them on affordable price.

true - about sensitivity but from experience I can tell if you have a quite stable supply voltage source no problem to program GALs.

currently I'm using something like this: one:Agilent DC-voltage supply E3646A. 0-8V, 3A /0-20V, 1,5A. YoC: For Sale (http://www.labx.com/v2/spiderdealer2/vistaSearchDetails.cfm?LVid=8428031)

all the best!

[HSN]

CAN SOMEONE PUT DUMPS ONLINE FOR DIFFERENT LANGUAGES AS ENGLISH, WHAT IS THE PROBLEM???

ONE THREAD FOR ALL THAT VAG QUESTIONS = STUPID

[JetSet59]

CAN SOMEONE PUT DUMPS ONLINE FOR DIFFERENT LANGUAGES AS ENGLISH, WHAT IS THE PROBLEM???

ONE THREAD FOR ALL THAT VAG QUESTIONS = STUPID

The last Free DUMP is the 908 English (seem to be out by a "error"), all other DUMP are not Free.. Bizness is Bizness...

[dariusddj]

i instaled comodo firewall free and i select to block vcds.exe and now vcds can't acces the internet and my cable is secure

[rsibiza]

CAN SOMEONE PUT DUMPS ONLINE FOR DIFFERENT LANGUAGES AS ENGLISH, WHAT IS THE PROBLEM???

ONE THREAD FOR ALL THAT VAG QUESTIONS = STUPID

There is no problem to do;)

You can post all your dumps you want..french german romanian...you can all post here.

Thx for sharing,best regards.

[vlad2s]

Ne mogu posmotretj eto predstavlenie

[willy789]

Has anyone looked at a 162 eeprom dump
an knows whats bytes are different for the different language versions? Only dumps i have seen have all been English .Or
let me know where i can find a different language dump,version 805 up preferred.

Thankyou

[s3mick]

Hi all, need a little help please, been trying to reprogram my cable and think i may have blown something, the led does not work and shows as not connected to car, there is power at the solderd connection on the triac (if thats the correct term) and also at the diode, is there a fuse just before the diode that i may have blown or anywhere else i can check. Thanks for any help Mick.

[willy789]

Hi all, need a little help please, been trying to reprogram my cable and think i may have blown something, the led does not work and shows as not connected to car, there is power at the solderd connection on the triac (if thats the correct term) and also at the diode, is there a fuse just before the diode that i may have blown or anywhere else i can check. Thanks for any help Mick.


Can you program the FTDI chip,have you tried the work arounds for when that chip gets nuked ? Also were you programming the atmega 162 eeprom,an incorrect eeprom for the version of VCDS you are running an it will nuke the 162 eeprom an also nuke
the FTDI chip.

[s3mick]

Hi already programmed the chip once and it worked but still not activated, would only run part scan. Tried re programming again but may have shorted something, had a couple of loose wires, just wondered where to check thanks mick

[eikido]

Cool, i'm getting this cable after reading this thread :)
Too bad ebay is so strict on this one :D

[Maartinj]

I was thinking aboutr translate this software. Did anybody know how to do this? or maybe only errors code ? Long code help file its easy, but erros look like they are deeper?

[blue36]

Hi, please upload FTDI_Tools programs!
Thanks in advanced!
Regards!
EDIT!
I have a BIG problem.
My 704 can not recognized from windows.
I received message "Unknown Device"
I used Win XP pak3. USB\VID_0000&PID_0000\6&35D10E8B&0&1
What can i do, please?
Thanks!

[rsibiza]

Hi, please upload FTDI_Tools programs!
Thanks in advanced!
Regards!
EDIT!
I have a BIG problem.
My 704 can not recognized from windows.
I received message "Unknown Device"
I used Win XP pak3. USB\VID_0000&PID_0000\6&35D10E8B&0&1
What can i do, please?
Thanks!


Start reading threat from post 1 on,imm sure you will fall over the solution. But it will take some time.

All is there.

Best regards.

[dimitar]

Hi, please upload FTDI_Tools programs!
Thanks in advanced!
Regards!
EDIT!
I have a BIG problem.
My 704 can not recognized from windows.
I received message "Unknown Device"
I used Win XP pak3. USB\VID_0000&PID_0000\6&35D10E8B&0&1
What can i do, please?
Thanks!

just google ftdi tool you'll find all you need and as far as atmega reflashing is concerned search thru DK. You dont read enough mate:barscarf:

[cniky]

Hi, please upload FTDI_Tools programs!
Thanks in advanced!
Regards!
EDIT!
I have a BIG problem.
My 704 can not recognized from windows.
I received message "Unknown Device"
I used Win XP pak3. USB\VID_0000&PID_0000\6&35D10E8B&0&1
What can i do, please?
Thanks!
Change 93c46 IC , is connected to FT232BL. That circuit is broken.

[esrodi]

Change 93c46 IC , is connected to FT232BL. That circuit is broken.

The circuit can be broken, but try to reprogramm 93c46 before change it. Maybe it is fully erased.

[blue36]

Thanks!
Is not problem to changed IC memory, she is work if programing with Wilhem before to change?

[bibkare]

Thanks!
Is not problem to changed IC memory, she is work if programing with Wilhem before to change?

What the f.u.c.k. was that

[KenshinPT]

Thanks!
Is not problem to changed IC memory, she is work if programing with Wilhem before to change?

I love google translator =)

[blue36]

Sorry man but not speak English so well!
Sometimes i used google translate.
I will try to change 93c46 memory after programing with Wilhem.
Thanks!

[esrodi]

Have you tried to use mprog?

[alex_SW]

hi.i have a 912 cable,clone....
if i run 10.6 software will i damage it?or can it be updated from 912 to 10.6??

tnx

[mattydr67]

hi.i have a 912 cable,clone....
if i run 10.6 software will i damage it?or can it be updated from 912 to 10.6??

tnx

If you'll use 10.6 you'll demage your tool.
If you update to 10.6.0 you can use that softwear. But the question is....do you have a tool qith FT232BL or BM inside?
And if iyou have this kind of tool...do you have dumps for it?
Good luck

[rsibiza]

hi.i have a 912 cable,clone....
if i run 10.6 software will i damage it?or can it be updated from 912 to 10.6??

tnx


The 912 clone should normally be ftdi bl/bm based and u can easyli update your interface.

But dont update by Rosstech sw,u need flash atmega162 with the dump for 10.6 with some usbasp programmer...

U can find infos on how to in this threat:

http://www.digital-kaos.co.uk/forums/f154/updating-atmega162-vcds-other-interfaces-166596/#post806195

[willy789]

hi.i have a 912 cable,clone....
if i run 10.6 software will i damage it?or can it be updated from 912 to 10.6??

tnx

As far as i have seen,right now there are no free dumps for 10.6 around,so
just run your cable with 912 software.

[dumm5]

HI i have an Audi a6 4f and need obd software

[lee_hdi]

Would this be ok to scan and change settings on VAG cars? - Vag com 10.6(FT 232 BL), (http://www.carsung.net/EN/ProShow.asp?ProID=824)

And do you think it will include the software?

Thanks

[spongemak]

Indeed it was a great job this finding :)

But i have a little problem, i can?t run the exe. the program has 2 exe, one of them is the one that the shortcut on desktop leads to, and when i click it (the shortcut or the exe itself), nothing happens!

I've tried on 2 different computers (Windows 7 32 and 64bit) and the result is the same.

Can someone give a suggestion?

Thanks in advance

You have to set the shortcut created by the installer to windows XP compatibility, the correct exe is VAG1062.EXE

[spongemak]

This will work with FT232BL?

Thanks

This is only for 10.6.2 cables that came with bad software.

[mattydr67]

Would this be ok to scan and change settings on VAG cars? - Vag com 10.6(FT 232 BL), (http://www.carsung.net/EN/ProShow.asp?ProID=824)

And do you think it will include the software?

Thanks

If it's what they said the sw will not be a problem.
Normally they will provide the sw but you know the companies it is a Chinese one, everything could happend.
Well you can try.
Good luck

[PEDRO4053]

Hello

I have a problem with my cable vcds 812 atmega 162 ft 232bl I don't get to carry the files vcds908 flash and eprom.hex * with PonyProg2000 ,mais the files vcds805.bim carries normal it will be that has some protection in the atmega162 or the files that I have they are bad.

Thank you
Pedro
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index69.html#post963331

[mr--x]

I bet in the USB-SERIAL Adaptor.

Usually they never work for this kind of applications: uC programmers, programmable automation controller...

You can try a PCMCIA or ExpressCard adaptor:

For old laptops with PCMCIA:
PCMCIA to RS-232 Serial DB9 CardBus Adapter Card Laptop - eBay (item 370481493060 end time Mar-06-11 02:43:56 PST) (http://cgi.ebay.com/PCMCIA-RS-232-Serial-DB9-CardBus-Adapter-Card-Laptop-/370481493060?pt=LH_DefaultDomain_0&hash=item56426af444)

For new laptops with ExpressCard:
*RS-232 Serial Port Express Card ExpressCard Adapter - eBay (item 230513418951 end time Mar-17-11 01:51:53 PDT) (http://cgi.ebay.com/RS-232-Serial-Port-Express-Card-ExpressCard-Adapter-/230513418951?pt=LH_DefaultDomain_0&hash=item35ababa2c7)

USB<->RS232 adaptors emulates a COM port and sometimes the emulation won't work for some devices (programmers and PLCs)

Those PCMCIA or ExpressCard adaptors add a physical COM port to your laptop.

I know, this post is some time ago but I think it is important to know:

"--> Compatible to USB2.0 Full Speed throughput"
This means, that the Chipset is universal serial Bus (USB).
In the device manager you will find "usb serial converter COMx) - same as a 2$ USB-Serial Converter.

Most cheap cards are working as USB-to-Serial. This is the same as you can use a normal USB-to-Serial Adapter. These cards doesn't even work togeter with many diagnostic tools.

Better you buy a card with Oxford chipset. Like the "EX-1350" or "EX-1370" or similar. These cards work as good as a real RS232/COM Port. I know many people who had this problem.

Try to connect an old opeltech or carsoft interface with the cards. Then you will see. It will not work, if you havn't an Oxford chipset.

[Carlos_]

You have to set the shortcut created by the installer to windows XP compatibility, the correct exe is VAG1062.EXE

Still not working :(

[s3mick]

Hi all. I've tried to repair my 704 cable and completely f*cked it up, been in touch with an ebay seller and he can provide a 10.6 cable, will this be ok to use with the vcds 805 software, or will I have to flash anything, also is there anything I should ask the seller about the cable. Thanks mick

[xanubysx]

Adjust the cable as VCDs 10.6 to version 10.6.3 en?? Anyone got a working DUMP? Thank you ... We VCDs CLONE making trouble, sometimes it does not find the pc ... pc is fine, so I want to try another version or 10.6.2, if anyone has unlocked DUMP please share ....

[mr--x]

After thousands of posts, many good tutorials, and several hours, I am sure now, not to find any Dump for the German 908. But now I know that serveral people have it ^^

So if you will change/trade - let me know what you need or what you want to have for it. --> PM

Thank you.

By the way... If you delete all double messages and questions here in the thread, I think the thread would get very small - hehe

[paffendorfbg]

nobody did it :beheaded:

vcds 10.6.2.exe locked 4 of my clones (vag 106)after 5 -6 times usage
so is there somebody to check this one


VCDS-Release-1063-Installer.rar - 4shared.com - online file sharing and storage - download (http://www.4shared.com/file/-pwkvPEn/VCDS-Release-1063-Installer.html)

[tk500]

nobody did it :beheaded:

vcds 10.6.2.exe locked 4 of my clones (vag 106)after 5 -6 times usage
so is there somebody to check this one


just use good old 908
all china 106 have huge problems

[DB77AAA]

I buy VAG com 10.6, chinesse clone. I use whit VCDS10.6.0 software, whith VAG-COM 704.1 and not working,
For test interface all OK, but tell vag com is not conected on car. Test is on VW Jeta 2009.
Interface is defective, or software, or I dont know to use?!?.

Thanks.

[cosmind]

you have not bought from the right guy
I have 2 different vag106, 1 is work ok with original software (704-10.6) and other work only with chinese cracked version.

how can I reprogram a locked atmega162? tried with beeprog and LPT programmer and can not read or erase

[mattydr67]

you have not bought from the right guy
I have 2 different vag106, 1 is work ok with original software (704-10.6) and other work only with chinese cracked version.

how can I reprogram a locked atmega162? tried with beeprog and LPT programmer and can not read or erase

You need a doctor to unlock Atmega.
@DB77AAA you know to use it I suppose that your interface is not what you expect to be.
Good luck

[mishu_b]

...
to unlock the Atmega you need an parallel programmer, means high voltage programming.

all the best!

[DB77AAA]

Thanks Misu and Dragos.
Misu!. I think I can visit you in few days.

[kacerrr]

Hi I have a question.
I have Chinese cable VAG908 Dual-K & CAN <-> USB.
This cable only works with older cars (K-line). Communication does not work if you join a new car (CAN).
Do you know what is wrong?
VCDS Test write - CAN: Not ready
Thank you.
http://img836.imageshack.us/i/testcan.png/
http://img535.imageshack.us/i/can1g.jpg/

[rsibiza]

Hi I have a question.
I have Chinese cable VAG908 Dual-K & CAN <-> USB.
This cable only works with older cars (K-line). Communication does not work if you join a new car (CAN).
Do you know what is wrong?
VCDS Test write - CAN: Not ready
Thank you.
http://img836.imageshack.us/i/testcan.png/
http://img535.imageshack.us/i/can1g.jpg/


Which car did u test.

Golf 4 is not CAN based chassis,need test minimum Golf 5

[alex_SW]

did someone test this??
http://www.digital-kaos.co.uk/forums/f172/vcds-10-6-3-908-cable-196305/

[kacerrr]

Which car did u test.

Golf 4 is not CAN based chassis,need test minimum Golf 5

I tried it on Skoda Octavia II (1Z chassis) Ross-Tech: VAG-COM: CAN-Bus Information (http://www.ross-tech.com/vcds/canbus.html). Manufacture-2004. I tried two new cars, always the same problem. CAN do not working. K-line yes.

Thanks.

[rsibiza]

did someone test this??
http://www.digital-kaos.co.uk/forums/f172/vcds-10-6-3-908-cable-196305/


If u read carefully u see its not working:beheaded:

[rsibiza]

I tried it on Skoda Octavia II (1Z chassis) Ross-Tech: VAG-COM: CAN-Bus Information (http://www.ross-tech.com/vcds/canbus.html). Manufacture-2004. I tried two new cars, always the same problem. CAN do not working. K-line yes.

Thanks.

U can try replace Can Drivers,on some interface it changed to working others not...some never got to work on CAN

[d1slon05]

Hi,

I spoke with a professional guy and he told me to update my chinese cable using the latest 10.6 firmware and course it broke my cable.
Any idea if it can easily be fixed, or should I just buy a new chinese one?

thanks

[rsibiza]

Hi,

I spoke with a professional guy and he told me to update my chinese cable using the latest 10.6 firmware and course it broke my cable.
Any idea if it can easily be fixed, or should I just buy a new chinese one?

thanks


Read this threat and figure out what choice u will Make.

http://www.digital-kaos.co.uk/forums/f154/updating-atmega162-vcds-other-interfaces-166596/#post806195

[PEDRO4053]

Somebody that already saw this cable, it could help me he has a plate with CI the reference it was turned off and a place with 6 pins tied the atemega through where I get to carry the dumps.bim with success. When has just recorded in the ponyprog recorded with more success the led red algem it is it could help me?


thank you
Pedro

http://images.orkut.com/orkut/photos/OgAAAB3eokcns3-efG9jrwR78K-rbs4FmF3TM1oVXk5UoFvep0GF_hmbDXtmgNCOn5uoPT0D66dho UYLW_3DSzQzKd8Am1T1UAKBfZcdesOoH7Lj22CyD-sHnpgl.jpg

[kacerrr]

U can try replace Can Drivers,on some interface it changed to working others not...some never got to work on CAN

Please. How Can I replace the Can Drivers? Do you have any tutorial and drivers?

Thanks.

[LuisAndre]

To all who asked me for the thread i have created about vcds, DK removed that thread because "Inappropriate Language".

Ok, my english it is not that good but i dont remember to be rude to anyone. Also, in this warning message, it says "Do not post any more cracks it is against the rules". I asked the moderator about all the cracked programs here in DK, files hosted by DK... No answer. And i only post links for the files, i didnt post any crack directly here. Anyway, i dont make the rules so i will follow those rules. I wont post were but if someone want to test the last loader for the program, just send me a message.

[mattydr67]

Mate the loader is for what version?
Please.
Thanks
Good luck

[LuisAndre]

Mate the loader is for what version?
Please.
Thanks
Good luck


for 10.6.3 version.

[esrodi]

Today I have tried to update my cable, but something went wrong and the atmega hasn't been programmed correctly. During the flash verification ponyprog showed an error, and the programming process stoped.

Then, I tried again to reprogram the atmega, but now ponyprog shows "Error 24" and I'm unable to do it.

What is happening? I think that atmega is blank. Do I need to use a HVP programmer to write it?

Sorry for my english.
Regards.

[LuisAndre]

Did you erase the avr first? you can't write on the flash without erase it first...

[esrodi]

Yes, I did.

[mattydr67]

for 10.6.3 version.

One more question please.
This will work with my 10.6.0 ft232BL tool?
Thanks very much
Good luck

[LuisAndre]

One more question please.
This will work with my 10.6.0 ft232BL tool?
Thanks very much
Good luck


Other users told me it works well with that cable... even with firmware 1.81.

[autochampion]

Well Works from 1.83 and BL as the chip


Other users told me it works well with that cable... even with firmware 1.81.

[mattydr67]

One question
Do I need to run the patch everytime or just at the first time?
Good luck

[bibkare]

I tried to download the patch even my AV NOD32 was deactivated but still keeps to delete it and warns me that virus was detected, anyone has the same problem?

[JetSet59]

"trojan detected" with Kaspersky but think it's was a false positive

[blackpirate]

I tried to download the patch even my AV NOD32 was deactivated but still keeps to delete it and warns me that virus was detected, anyone has the same problem?


1. haveing the AvV deactivated , it cant delete it!
2. the file its clean! ;)

it just a false alarm caused by the protector!

scan it on virustotal.com

cheers:party: L.A

[alex_SW]

if someone can confirm if it works with 912 interface....i have a 912 but right now i dont have car to test....

[KenshinPT]

One question
Di I need to run the patch everytime or just at the first time?
Good luck

WRONG INFO:
Maybe you already know the answer but you don't need to patch it everytime you open VCDS. xxxxx

But I only tested the cable without a car. I tested only plugged into a 12V power supply.

Regards


My bad... You need to patch everytime you run VCDS

[LuisAndre]

Maybe you already know the answer but you don't need to patch it everytime you open VCDS.

But I only tested the cable without a car. I tested only plugged into a 12V power supply.

Regards

No, everytime you start vcds, you need to run the patcher... because this patchs are done on the program memory and not on the disk. If you run only vcds, you may end with a dead cable...

[cmacinnes86]

Hi guys,
quick question, I have an old K-Line 409 Vag-Com lead with F232BM chip. Is there any way to upgrade firmare here to clone a VCDS 908 lead.
FYI I have cracked copy of Lite which is decent but lacking a lot of the new features that were added from v908. I have a Passat B5.5 without CAN interface, don't plan to upgrade car soon so doesn't even warrant buying updated clone cable..... unless it could allow access to full VCDS software features.
Any help would be appreciated!
Cheers.

[angelx431]

Hi guys,
quick question, I have an old K-Line 409 Vag-Com lead with F232BM chip. Is there any way to upgrade firmare here to clone a VCDS 908 lead.
FYI I have cracked copy of Lite which is decent but lacking a lot of the new features that were added from v908. I have a Passat B5.5 without CAN interface, don't plan to upgrade car soon so doesn't even warrant buying updated clone cable..... unless it could allow access to full VCDS software features.
Any help would be appreciated!
Cheers.
No updated

[LuisAndre]

Just some pictures... no illegal crack whatsoever here.... Remember, DK don't allow you to have it!

[cmacinnes86]

No updated

??

:embarassed:

[LuisAndre]

??

:embarassed:


I think he means you cant update your cable :rofl: ... give yourself a present and buy a chinese crap cable...

[cmacinnes86]

I think he means you cant update your cable :rofl: ... give yourself a present and buy a chinese crap cable...

Good shout.... Chinese crap it is!

:burnout:

[esrodi]

??

:embarassed:

This cable can't be updated. There isn't an atmega inside of it.

[nagyotti]

I think that here peoples

[silikon21]

Hi! Everyone!
I have a problem with a cloned chineese vag 704.1.
I got it from a client for repairs.
I have reflashed atmega with 704.1 files.
The cable is now recognized by the computer and the vag com, but when I connect it to the car, i get no response from the controller.
When I click in the vag to connect to any controller the led on the cable is blinking, a couple of seconds later I get the error.

I think it is a hw error on some of the components. Please help to resolve the problem.

Here are the pictures form the cable and vag com :

https://lh6.googleusercontent.com/_AFCrqi_T4Uc/TYtLWZ4N3eI/AAAAAAAACvI/H3HO5tdKiWk/s800/704-1.jpg

https://lh3.googleusercontent.com/_AFCrqi_T4Uc/TYtMX-bkHrI/AAAAAAAACvo/rAtr50gbbe0/vag%20error.JPG

https://lh5.googleusercontent.com/_AFCrqi_T4Uc/TYtLtK8dLsI/AAAAAAAACvY/kcbZDHUTux4/s912/704-1-2.jpg

[silikon21]

Hi! Everyone, I've managed to repair the cable. The problem was that the pin #7 (K-Line) was not connected to the board correctly. So no communiocation with the car was possible.

Best regards!

[esrodi]

Today I have tried to update my cable, but something went wrong and the atmega hasn't been programmed correctly. During the flash verification ponyprog showed an error, and the programming process stoped.

Then, I tried again to reprogram the atmega, but now ponyprog shows "Error 24" and I'm unable to do it.

What is happening? I think that atmega is blank. Do I need to use a HVP programmer to write it?

Sorry for my english.
Regards.

My cable is working again :D. All I needed was to connect an external clock signal to pin 15 of Atmega162. I got this clock signal from a PIC. As the update process crashed, the fuses was wrong, and atmega didn't start.

Regards.

[PEDRO4053]

My cable is working again :D. All I needed was to connect an external clock signal to pin 15 of Atmega162. I got this clock signal from a PIC. As the update process crashed, the fuses was wrong, and atmega didn't start.

Regards.


Hello I have the same problem with my cable, it will be that you were able with doing this work in the pin 15 of the atmega.

thank you
Pedro

[zecas]

hi
is there an simlpe way to simulate CAN in this cable so i can see "CAN ready" my car only have k line.

[mr--x]

Does anybody have a Binary file from the GAL26V8B?
I have the JED but need the bin for flashing with a programmer (with PLCC 20 Adapter)...

[esrodi]

Hello I have the same problem with my cable, it will be that you were able with doing this work in the pin 15 of the atmega.

thank you
Pedro

You have the same problem, and what else? I'm not able to understand that you mean. Could you explain the problem better?

Regards.

[PEDRO4053]

You have the same problem, and what else? I'm not able to understand that you mean. Could you explain the problem better?

Regards.

I recorded the epron and flash when I went to record the fuziveis the ponyprog it turned off when I tried to record again he/she gave error 24. Now I don't tie the cable, as I do to have this sign in the pin 15 of the atemega?

Excuse my English I use Google translator

thank you
Pedro

[KenshinPT]

I recorded the epron and flash when I went to record the fuziveis the ponyprog it turned off when I tried to record again he/she gave error 24. Now I don't tie the cable, as I do to have this sign in the pin 15 of the atemega?

Excuse my English I use Google translator

thank you
Pedro

Maybe you set wrong fuses... for example: you disable SPIEN, or you activated FLASH/EEPROM protections.

[PEDRO4053]

Maybe you set wrong fuses... for example: you disable SPIEN, or you activated FLASH/EEPROM protections.



I turned off atmega later I recorded the epron and flash when I went to record the fuziveis he/she gave error 24, now my cable doesn't call. I try to turn off the atmega of the error 24 my ,o cable this died with I do to do him to call again.


Pedro

[mattydr67]

Just some pictures... no illegal crack whatsoever here.... Remember, DK don't allow you to have it!

Great job LuisAndre.
Did you tried on a car?
VCDS 11.2 it's need firmwear 1.84 to work well from what I know.
I will try today the 11.2.
The 10.6.3 works great with my VCDS 10.6 tool with BL inside.
Good luck

[mladen76]

Great job LuisAndre.
Did you tried on a car?
VCDS 11.2 it's need firmwear 1.84 to work well from what I know.
I will try today the 11.2.
The 10.6.3 works great with my VCDS 10.6 tool with BL inside.
Good luck

I have 10.6 whit a RL chip insade,I heard that it is not good chip so aht is the diference betwen RL-BL and can someone thel me will 10.6.3 coud work whit my cable or...?

[LuisAndre]

Not true... You can use firmware 1.83 on v11.2.0. I have tested my loader for v11 beta on several cars... So far so good.. No bad error codes, good live view, autoscan works on both can and kl.... I dont have 10.6 dump, so i cant give live to my broken 10.6 RL cable so i can only do some tests and loaders to 908 cables.

[mattydr67]

Yesterday I tested the 10.6.3 and it works great on two cars.
Today I tried to conect to another car that come in the garage and when I plugged the interface it asked me for the drivers and the conclusion is that the interface Atmega was erased.
Yesterday I run the exe file then the patc and I didn't push exit I let it on the screen.
My interface it was ft232BL 10.6.0 with dump.
LuisAndre please tell me if I did something wrong?
Or is just becasue my tool have ft232BL inside and it was programmed with 10.6.0 dumps. I have firmwear 1.83 as well.
Good luck

[jo?o antonio]

H? mate ,

some version 10.6.3 for test ?

my cable is FW 1.83 chinese , but is ( USB direct ross-tech )

version 10.6.2 doesn't works , is bad , cell 000 measure bloks do not show .

Thank you for all DK members.

[mattydr67]

I fixed my tool and now it's working again.
I just reright the ftdi with Mprog.
I don't know what happend that it changed the driver after I used with VCDS 10.6.3.
But it dosen't erased the Atmega, just changed the ftdi drivers.
Now it's workingf again and I will try on several car and then I will try back with the 10.6.0
Maybe this was casue of driver changing.
It's working with 11.2 too but I think that for new protocols you need to upgrade the firmwear to 1.84
I will try to do this to see if I will have a new protocol car to try.
Now it's working with 1.83 how LouisAndre said.
Good luck
:party:

[paffendorfbg]

Please share your .ept
:embarassed:

[mattydr67]

Please share your .ept
:embarassed:

ept files are here.
it is the same like for 908.
@LouisAndre
I tested again and it erase my Atmega again.
I can repair the ftdi I can do the TEST and everythings ok but when I wanna do an Autoscan, it search just 2 controlers and then stopped.
In ABOUT it show the serial but it aint Full Registred/Activated.
So in conclusion this patch it is ok for ftdi232RL not for BL
Atention: For the mates who have dumps you can try but if you have and you cannot reprogrammed, don't try becasue you'' cry after.
I'm reprogrammed mine and I will forget about this "patch"
Thanks for trying.
Good luck
:party:

[LuisAndre]

No m8, I only have BL cables... And it works... Anyway, you are right in one point... autoscan doesn't work very well..
And you can find the dumps for the cable here on DK if something goes wrong. Again, use it only if you want... thats the spirit.

I also sent you the new loader for V11.2.

Anyone interested on this , pm me.

[mattydr67]

No m8, I only have BL cables... And it works... Anyway, you are right in one point... autoscan doesn't work very well..
And you can find the dumps for the cable here on DK if something goes wrong. Again, use it only if you want... thats the spirit.

I also sent you the new loader for V11.2.

Anyone interested on this , pm me.

Thank you very much LouisAndre but I told you, for me it dosent works and it erased the EEPROM twice using 10.6.3
No you don't understand me well, I used Autoscan and how I said it worked very well.
The day before yesterday it works great on several cars but yesterday when I plugged again into the USB the drivers was changed. I fixed it and it becomes Unregistred.
I reprogrammed the Atmega and after I tried Autoscan in few cars ( several times ). The EEProm was erased again.
Take care.
BTW I don't need dumps for 10.6 and I don' thik that's for free here.
Thanks again
Good luck

[easyobd]

Hi, can you advise me some Chinese seller, where I can buy VCDS hardware 10.60 or 10.62/63 with FT232BL/BM chip inside? There is so many bad sellers with even worst products, but maybe somebody has good experience with some companies?
And is the VAS 5054 better than VCDS?

[kodo28]

Could someone of you tell me where can I get an 912 original version sofware ?? impossible to find it on net...If someone can send it for me
:party:

[liviudiaconu]

[...]
The day before yesterday it works great on several cars but yesterday when I plugged again into the USB the drivers was changed. I fixed it and it becomes Unregistred.
I reprogrammed the Atmega and after I tried Autoscan in few cars ( several times ). The EEProm was erased again.
Take care.
[..]
Good luck

After FEW autoscan Atmega is erased by the 10.6.3, every new version is a "clock bomb" for the old serials..

[mattydr67]

Thanks Liviu I didn't know this.
Now I know why everytime it erased my EEPROM.
This is is.
Good luck

[selimoglu]

thank you mac

[asacity]

any idea about my thread

http://www.digital-kaos.co.uk/forums/f152/folding-mirror-golf-5-golf-6-a-197833/

[easyobd]

Hi, I have 2 VCDS hardware, one is the Vag 704 with FT232BL chip which I can fix with no problem(downgrade, upgrade etc), and second cable VCDS 908 with FT232RL, which is broken at the moment and I can't fix it. I tried to fix it like in manual on DK about cables with RL chip, but this doesn't work for me.
My question is why is so hard to fix cables with RL chip. Is that really big problem to fix them? If cables with BL/BM chip we can quite easy fix, so where is the problem about cables with RL chip. What do we need to fix them. I know that they have different FTDI chip, and they build in slight different way, but they are not that much different. I ask it because is very hard, and soon will be even more harder to buy hardware with BL/BM chip. Nearly all new Chinese VCDS(10.62, 10.63) clones comes with RL chip, and probably the 11xxx version onward will be build with RL chip as well. So what will be solution to fix them? Nobody want keeps collection of broken cables at home. We want to fix and use them. If Chinese manage to made them, they also can be fixed? Do they?
Thanks.

[mattydr67]

Hi, I have 2 VCDS hardware, one is the Vag 704 with FT232BL chip which I can fix with no problem(downgrade, upgrade etc), and second cable VCDS 908 with FT232RL, which is broken at the moment and I can't fix it. I tried to fix it like in manual on DK about cables with RL chip, but this doesn't work for me.
My question is why is so hard to fix cables with RL chip. Is that really big problem to fix them? If cables with BL/BM chip we can quite easy fix, so where is the problem about cables with RL chip. What do we need to fix them. I know that they have different FTDI chip, and they build in slight different way, but they are not that much different. I ask it because is very hard, and soon will be even more harder to buy hardware with BL/BM chip. Nearly all new Chinese VCDS(10.62, 10.63) clones comes with RL chip, and probably the 11xxx version onward will be build with RL chip as well. So what will be solution to fix them? Nobody want keeps collection of broken cables at home. We want to fix and use them. If Chinese manage to made them, they also can be fixed? Do they?
Thanks.

Well maybe the Chinese dosen't want to fix the tool just becasue they need to sell more and when they did this FT232RL it was just becasue they dosen't want un upgradable tool.
Didi you tried exaclly like in Aminebot tutorial?
I mean did you reprogramm the GAL16V8 and changed the PCB circuit?
Good luck

[8k65m]

I have China VCDS 10.62 on FT232R.
After experimenting with different programs, I got the "Unknown device ". But before the experiments I'm using FT_Prog kept flashing.
I restored my VCDS with FT_Prog without a soldering iron, restoring the old firmware and serial number.
Best regards.

[easyobd]

Well maybe the Chinese dosen't want to fix the tool just becasue they need to sell more and when they did this FT232RL it was just becasue they dosen't want un upgradable tool.
Didi you tried exaclly like in Aminebot tutorial?
I mean did you reprogramm the GAL16V8 and changed the PCB circuit?
Good luck

I wasn't asking Chinese to fix it, because they don't want to fix anything, doesn't matter what did you buy from them. Like you said they only want sell more and more products.
My question was why is so hard fix hardware with RL chip, and why we can't fix it by themselves like we do it with BL/BM cables. If Chinese somehow programmed RL cables with 908, 912, 10,60, 10.62, 10,63 ++++ dumps it means that they can be reprogrammed - but HOW???
Yes, I did reprogram GAL and and change PCB circuit, but cable still doesn't work.

[mattydr67]

I wasn't asking Chinese to fix it, because they don't want to fix anything, doesn't matter what did you buy from them. Like you said they only want sell more and more products.
My question was why is so hard fix hardware with RL chip, and why we can't fix it by themselves like we do it with BL/BM cables. If Chinese somehow programmed RL cables with 908, 912, 10,60, 10.62, 10,63 ++++ dumps it means that they can be reprogrammed - but HOW???
Yes, I did reprogram GAL and and change PCB circuit, but cable still doesn't work.

You need to use dumps for 908 posted by Amineboth.
If that will not work I can't say anything
Good luck

[coolk0415]

hello i have vcds 10.6 chinese... it worked maybe 10 day and then it died... when i plug it into usb cable is identified as "FFFFFFFFFFF..."... cable runs on ft232bl and doesnt have stc chip.. does anyone have solution for this? i will upload pics.. thank you
vcds 10.6 chinese....

Share ok?

I need vcds 10.6 chinese

[ironderek]

vcds 10.6 chinese....

Share ok?

I need vcds 10.6 chinese

He meant that he has 10.60 clone cable from China lol.
How he supose to shere it with you lol. You have to buy one for yourself. If you looking for 10.60 atmega dump I dont think that somebody will share it for free :)

[LuisAndre]

After FEW autoscan Atmega is erased by the 10.6.3, every new version is a "clock bomb" for the old serials..


Yes m8, and if you connect your cable to a 1974 Volkswagen Scirocco, it will start a nuclear fusion inside of atmega.

:pcguru:

[mattydr67]

Yes m8, and if you connect your cable to a 1974 Volkswagen Scirocco, it will start a nuclear fusion inside of atmega.

:pcguru:

My dear friend you don't understand what he wanna say.
He said that if you use a tool with 11.2 or 10.6.3 then if you use your tool with a downgrade version of sw like 10.6.0 or 908 then your tool ( ATMEGA ) will be erased.
In conclusion: after you try your loader then never go back to use the interface with a previos sw.
It happend to me too I told you.
Good luck

[LuisAndre]

My dear friend you don't understand what he wanna say.
He said that if you use a tool with 11.2 or 10.6.3 then if you use your tool with a downgrade version of sw like 10.6.0 or 908 then your tool ( ATMEGA ) will be erased.
In conclusion: after you try your loader then never go back to use the interface with a previos sw.
It happend to me too I told you.
Good luck

No my friend... You dont understand... And when i say You, I mean a lot of You... There is no fuse bomb. You can't downgrade to any version... but you can't upgrade either, simply because the cracked version will mark interface as an unregistered cable on the AT eeprom area... Why it still works on a cracked version? because the cracked version bypass that check. The right way to say it is: you can't use an original version after use a cracked one...
And you can use a previous version... If you use a cracked previous version. Now you know why yellow guys sells the crap cable and provide software version 708, 805,908,912 and 10.6. ALL CRACKED and with the warning : Do not use this crap cable with any other software...

(Sorry, i don't like Mr. Wang.)

And good luck to you too.

[nkstyle]

I have China VCDS 10.62 on FT232R.
After experimenting with different programs, I got the "Unknown device ". But before the experiments I'm using FT_Prog kept flashing.
I restored my VCDS with FT_Prog without a soldering iron, restoring the old firmware and serial number.
Best regards.

Can you share this backup?

I also trying repair FT232R with FT_Prog but i dont have the backup.

[mattydr67]

No my friend... You dont understand... And when i say You, I mean a lot of You... There is no fuse bomb. You can't downgrade to any version... but you can't upgrade either, simply because the cracked version will mark interface as an unregistered cable on the AT eeprom area... Why it still works on a cracked version? because the cracked version bypass that check. The right way to say it is: you can't use an original version after use a cracked one...
And you can use a previous version... If you use a cracked previous version. Now you know why yellow guys sells the crap cable and provide software version 708, 805,908,912 and 10.6. ALL CRACKED and with the warning : Do not use this crap cable with any other software...

(Sorry, i don't like Mr. Wang.)

And good luck to you too.

That's what I wanna said. Thanks.
When I use original version of 10.6.0 with BL tool and I told you that it works with your loader.
But I can't downgrade to original 10.6.0 sw
That's it. If I will need a tool to change the sw I will buy a genuine tool.
Good luck

[angelx431]

Can you share this backup?

I also trying repair FT232R with FT_Prog but i dont have the backup.
vcds 10.6.2 ft232rl.ept

[mladen76]

No my friend... You dont understand... And when i say You, I mean a lot of You... There is no fuse bomb. You can't downgrade to any version... but you can't upgrade either, simply because the cracked version will mark interface as an unregistered cable on the AT eeprom area... Why it still works on a cracked version? because the cracked version bypass that check. The right way to say it is: you can't use an original version after use a cracked one...
And you can use a previous version... If you use a cracked previous version. Now you know why yellow guys sells the crap cable and provide software version 708, 805,908,912 and 10.6. ALL CRACKED and with the warning : Do not use this crap cable with any other software...

(Sorry, i don't like Mr. Wang.)

And good luck to you too.

First thanks for the detaild explanation,and have to ask beginer question couse there is a lot information I dont understand,that crap cable you talk whit all the versions the chines send 708, 805,908,912 and 10.6 my antivirus only recognize v 908 as virus,but my question is,can I use this cable to do vw diagnostic,long coding.... and what software to use??

[tk500]

No my friend... You dont understand... And when i say You, I mean a lot of You... There is no fuse bomb. You can't downgrade to any version... but you can't upgrade either, simply because the cracked version will mark interface as an unregistered cable on the AT eeprom area... Why it still works on a cracked version? because the cracked version bypass that check. The right way to say it is: you can't use an original version after use a cracked one...
And you can use a previous version... If you use a cracked previous version. Now you know why yellow guys sells the crap cable and provide software version 708, 805,908,912 and 10.6. ALL CRACKED and with the warning : Do not use this crap cable with any other software...

(Sorry, i don't like Mr. Wang.)

And good luck to you too.


After is used your loader any other version (new or old) will destroy the eeprom
Also if the software knows it's modded can not say what would do - wrong DTC, codding, long codding and etc.
Chinese use cracked versions started form 908 and mainly from 10.6x.

[Qwarz]

I have been testing loader several times and VCDS is still alive :) My configuration is VCDS 908 with flash 1.81.

[mbenz1]

I just recieved a vag106 cable from china. The guy put a note in to message him when i get it and he would send the file. I have, bu i have to wait probably till tomorrow due to time difference.

Does anyone have this file? im guessing its not going to be the original one from ross-tech site.

Edit: it has RL chip

[tk500]

I just recieved a vag106 cable from china. The guy put a note in to message him when i get it and he would send the file. I have, bu i have to wait probably till tomorrow due to time difference.

Does anyone have this file? im guessing its not going to be the original one from ross-tech site.

Edit: it has RL chip


will work badly with cracked only soft

[mbenz1]

will work badly with cracked only soft

I don't understand. Do you mean I must not use cracked software with this cable?

[max4ever]

Exactly M8! Don't use cracked software for your interface, otherwise, your interface its gone!

[mattydr67]

With cracked sw works badly but you don't have anythingelse to do. This is it.
Good luck

[mbenz1]

Ok cheers, so should i use original software from ross-tech only?

Where from? which version? 10.6 or 10.6.3?

Sorry about all the questions i just dont want to burn this cable.

[max4ever]

Only 10.6 or old version!

[mbenz1]

Only 10.6 or old version!

Ok. Thanks but I can't find the original 10.6.0 without crack anywhere. Rosstech only show 10.6.3 on their site.

Thanks

[mattydr67]

Ok. Thanks but I can't find the original 10.6.0 without crack anywhere. Rosstech only show 10.6.3 on their site.

Thanks

M8 if you have a tool with Ft232RL inside do not use original version of VCDS.
Use just cracked chinese softwears.
Original softwears from ross-tech works with tools with FT232BL or BM inside.
If I said someting wrong please forgive me.
Good luck

[mbenz1]

Ok Thanks, i will wait till the guy sends me the software.

There seems to be a lot of conflicting information given on this thread

[angelx431]

M8 if you have a tool with Ft232RL inside do not use original version of VCDS.
Use just cracked chinese softwears.
Original softwears from ross-tech works with tools with FT232BL or BM inside.
If I said someting wrong please forgive me.
Good luck
Yes just ft232bl works 100%

[mattydr67]

Ok Thanks, i will wait till the guy sends me the software.

There seems to be a lot of conflicting information given on this thread

Really good choice.
No conflictes just read carfully from the begining of this tread and you'll see on the post of some guys like rsibiza, aminebot, bibkare,tk500 and many other from this forum ( and many others guys who I didn't mention and for that I apologize them ) who really know what they said. Other forgive me but just talk.
But this is it, it is an "open forum"
If your supplier will never send you the sw you need I will give you ( in PM ) a link to download what I recived before on a cd and it work with a tool Vag 106 like yours.
Good luck

[mbenz1]

Cheers guys im new to this

[DiagService]

Hi guys I need eeprom Dump 93c46 for VCDS 908

Thank s

[mishu_b]

Hi guys I need eeprom Dump 93c46 for VCDS 908

Thank s

which version RL, BL,BM?

atb

[DiagService]

My version is with FT232BL i need eeprom dump 93c46

[mattydr67]

My version is with FT232BL i need eeprom dump 93c46

I just replaced the 93c46 with a new one and then I reprogrammed the ft232bl with Mprog using ept file for 908.
And it works.
Difference between ft232RL wich have this eeprom inside of it and ft232Bl wich has separate eeprom is this.
For me it works how I said.
You can try.
Good luck

[max4ever]

You have PM

[supermario333333]

Hi @all,

I have a 10.6 cable with FTDI 232RL chip and would like reprgramm it to 908 german cable. Is it possible to use the 908 german dump (for BL chip cable) if I reprogram the GAL and delete the parts which are described in the Tutorial ?

thx

[rehtnap]

hi
will vag com diagnose read the self leveling headlights on a vw toureg.
and what interface does a full version of vag com use/

[rehtnap]

hi
nebie to vag com. have i got this right. vag106 cable will work with genuine software but if used with pirate software supplied is burnt to that software then genuine wont work.
can i ask how well does the chinese software work for diagnostics sounds like people who have used it arnt impressed.
and lastly am i right that there are 2 interface cables available kkl and k-can. i guess vcds needs the can version to work properly.
sorry for the questions but vag is new to me and after reading so many pages in here i want to know im going in the right direction.:afraid:

[mbenz1]

hi
nebie to vag com. have i got this right. vag106 cable will work with genuine software but if used with pirate software supplied is burnt to that software then genuine wont work.
can i ask how well does the chinese software work for diagnostics sounds like people who have used it arnt impressed.
and lastly am i right that there are 2 interface cables available kkl and k-can. i guess vcds needs the can version to work properly.
sorry for the questions but vag is new to me and after reading so many pages in here i want to know im going in the right direction.:afraid:

I have only used the software supplied with my vag106 and it works really well (as original software)... I didn't risk using original software as there is no point.

Yes there is kkl and k-can. Can is required for newer cars after about 2004 I think. KKL will also only work with old software v3/4 and vcds Lite i believe.

There is a lot of knowledgeable people on here

[DiagService]

Update ATmega 162 ---- VCDS 812
Everything is fine until PonyProg
PonyProg: Command...Erase
Device missing or unknown device (-24)

Help Help

thanks

[mishu_b]

...
- check connections between parallel port and your board!

- check the supply lines - have a look to the supply voltage
- check GND (-) connection.

atb

[KenshinPT]

Update ATmega 162 ---- VCDS 812
Everything is fine until PonyProg
PonyProg: Command...Erase
Device missing or unknown device (-24)

Help Help

thanks

1 - Your LPT cable isn't correct. Check the schematics again.

2 - You have short circuits in the thin wires that are connected to the ATMEGA. Recheck all connections with a multimeter.

3 - You haven't connected pin 25 of LPT port to GND.

4 - You haven't soldered the shield wire into the metallic part of the DB25 connector and then plug it into GND.

5 - You should try lower resistor. Try 820ohm, 680ohm, 560ohm, 470ohm, 390ohm... But, don't forget that those resistors are there to protect the LPT port, not the ATMEGA. Don't push the limits of the LPT port... so don't use resistors lower than 100ohm.

5a - After a couple flashes and while using low resistors you burnt your LPT port.

6 - Your LPT port is not set to ECP mode in BIOS.

7 - SPIEN fuse is disable. Probably the supplier disable that so they can prevent you from an easy update of your clone cable. You need to erase the ATMEGA via HVPP (High Voltage Parallel Programmer).

7a - After one flash, by mistake, you disable the SPIEN fuse. Again, you need to erase the ATMEGA via HVPP.
Good Luck

[DiagService]

Thank s KenshinPT I have programed with UPA
I have problem when I TEST USB
Status: Not plugged into CAR !!

Have you any ideas ????

THANK S

[aminebot]

Thank s KenshinPT I have programed with UPA
I have problem when I TEST USB
Status: Not plugged into CAR !!

Have you any ideas ????

THANK S

it should be an FT232R interface.
you have to do some modifs as explained in a previous post.

[DiagService]

Have you good Dumps for 908 vcds Atmel 162, FT232BL
Can you send to my manulas

[easyobd]

it should be an FT232R interface.
you have to do some modifs as explained in a previous post.

Hi Aminebot, I have interfaces 106 and 908 with RL chip, and I tried to fix them like in your manual(programming GAL and add 3wires) with 908 and 10.60 dumps but interfaces still don't work. How they supposed to be modified? What should be done to fix interface with RL chip?
Thanks.

[aminebot]

Hi Aminebot, I have interfaces 106 and 908 with RL chip, and I tried to fix them like in your manual(programming GAL and add 3wires) with 908 and 10.60 dumps but interfaces still don't work. How they supposed to be modified? What should be done to fix interface with RL chip?
Thanks.

you used original soft or modified ?

[easyobd]

you used original soft or modified ?

For 908 dump I used software which was over here incl. dump, to same for 10.60 dump software incl. version 10.6.0.0 13.5MB.

[aminebot]

For 908 dump I used software which was over here incl. dump, to same for 10.60 dump software incl. version 10.6.0.0 13.5MB.

you need to use modified software .
i uploaded in a previous post a 908 modified version.

[Barm76]

Can I find hire dumps for 10.6 VCDS for FTDI BM-based adapter?

[mattydr67]

Can I find hire dumps for 10.6 VCDS for FTDI BM-based adapter?

No you can't becasue it is not for free yet.
Good luck

[KenshinPT]

For those who need FLASH 1.84:

PS - This is just the FLASH 1.84 not the EEPROM for VCDS 11.2

Download FLASH1.84 (http://www.multiupload.com/O8S25Y4R4W)

Download:

[Tereksaz]

For those who need FLASH 1.84:

PS - This is just the FLASH 1.84 not the EEPROM for VCDS 11.2

Download FLASH1.84 (http://www.multiupload.com/O8S25Y4R4W)

Download::beer:
flash - it is very easy! it is not problem!
EEprom - it is more interesting
Write DUMP EEprom it is more easy, for me, for a example.
How do it?
=====
find only USB Monitor HHD Software ver. 3.0.0.1
instrution:
Start>
Install >Usb Monitor
Install Vag Com or VCDS
Reboot

Start>>>Usb Monitor
File>>>New session
Usb monitor
Select the usb device = Ross-Tech......or USB to Serial Com port
Request View
Windows =Complete (not Basic - only Complete)
Ok!

Next>>>
connect ADAPTER to +12v
Start Vag Com or VCDS
Options
Select Port >>USB or Com
Test>>
Close all Windows Vag Com

Next>> Usb Monitor
Push bottom >Stop
Push bottom > Export HTML
Any name > Save
Close > Usb Monitor

Next>>
Puk xxx.html to xxx.rar
Send to mail xc70td@gmail.com
and else - There is no difference - Chinese clone or original, only for FT232BM/BL
it'S instrution .
how to make a log file and write dump eeprom ATMEGA 162.
USB Monitor HHD Software ver. 3.0.0.1 => http://www.azlina.ru/download/monitor.zip
=Tereks=

[mattydr67]

Sorry a stupid quetion.
Do you wanna say that with your procedure you can write Atmega thrue USB?
I mean if you have dumps you can write item thrue USB.
Becasue for me it is easy to write it with a external programmer using write dumps.
But you procedure it is much easier if it is like you said or I undesrtand not well.
Good luck and thanks

[mishu_b]

...
why should I send you the result?
I don't get the point!!!!

could you please be more precise about this issue?

atb

[KenshinPT]

Sorry a stupid quetion.
Do you wanna say that with your procedure you can write Atmega thrue USB?
I mean if you have dumps you can write item thrue USB.
Becasue for me it is easy to write it with a external programmer using write dumps.
But you procedure it is much easier if it is like you said or I undesrtand not well.
Good luck and thanks

Yes, its possible to write the ATMEGA's memory via USB.

FLASH could be programmer via USB.

EEPROM I am not quite sure about that.

But I believe that EEPROM can also be programmed via USB because when you install a new VCDS version the serial changes, right?

[tk500]

:beer:
Send to mail xc70td@gmail.com
and else - There is no difference - Chinese clone or original
=Tereks=

can send to me also :laugh:
for originals based on ft232R will not to be enough

[DiagService]

Hi Friend s i have problem with FT232BL Atmega162

[DiagService]

HELP !!!!
Hi Friend s i have problem with FT232BL Atmega162
I have program Atmega162 with UPA when I Test
Port Status: OK
Interface: Found !
Status: Not plugged into Car !

My Led Blink one way when I conect 12v

[mattydr67]

Plug it into the car and see whats next.
Good luck

[autochampion]

HELP !!!!
Hi Friend s i have problem with FT232BL Atmega162
I have program Atmega162 with UPA when I Test
Port Status: OK
Interface: Found !
Status: Not plugged into Car !

My Led Blink one way when I conect 12v

As have put fuse in UPA ? The especial way is necessary :laugh:

[KenshinPT]

HELP !!!!
Hi Friend s i have problem with FT232BL Atmega162
I have program Atmega162 with UPA when I Test
Port Status: OK
Interface: Found !
Status: Not plugged into Car !

My Led Blink one way when I conect 12v

WRONG:
Make sure that your power supply has enough current to power up the ATMEGA.

I had that problem once... for example: if I power up directly the ATMEGA with the 5Volt from USBasp I get the blinking red problem... I don't know why but i thinks it doesn't have enough current.

CORRECT (thanks to Xoom)
Make sure you have 12V at the input of the regulator (7805)

[xoom]

it not current problem :) its becouse transistors dont have 12v so ATF dont get signal.. so Atmega thinks that its error :)

[mishu_b]

HELP !!!!
Hi Friend s i have problem with FT232BL Atmega162
I have program Atmega162 with UPA when I Test
Port Status: OK
Interface: Found !
Status: Not plugged into Car !

My Led Blink one way when I conect 12v

my dear friend,

You might have two problems, as far as I can see from your posts:

1. fuses program - did you programed fuses accordingly?
2. your dump it doesn't fit to your interface.

all the best

[DiagService]

I have erase chip, program flash program Fuse Bits, when I conect to
Test: Un plugged into Car !
Today I have change eeprom in VCDS 93c46 and nothing

If you have any idea REPLAY

Thanks All

[toquim]

I have erase chip, program flash program Fuse Bits, when I conect to
Test: Un plugged into Car !
Today I have change eeprom in VCDS 93c46 and nothing

If you have any idea REPLAY

Thanks All



When you test the cable is in the car? If not, disconnect the wires that flashes your Atmega and try again.

[mishu_b]

...
first question:
after re-flash the MCu do you get the LED on? (doesn't matter the color)

atb

[DiagService]

after re-flash Diod blikn once

[DiagService]

When you have good Dump From Atmega162 FT232BL and eeprom 93c46 can you Send to my.
If you're working with UPA Re-flash Atmega162 can you send to my manuals
I have no more ideas

Thank s ALL

[mishu_b]

...
2 possible issues as I told few lines above.

firs look carefully to fuse and afterwords try with a different dump.

all the best!

[DiagService]

I have change 7805 Regulator for 12V and eeprom 93c46
I read and flash Atmega162 and program fuse bits with UPA programer, when I conect 12V my LED blink one way

[KenshinPT]

I have change 7805 Regulator for 12V and eeprom 93c46
I read and flash Atmega162 and program fuse bits with UPA programer, when I conect 12V my LED blink one way

One important question:

Is your cable based in the FTDI232BL or FTDI232RL?

(FTDI232BL and FTDI232BM are the same - BL is Lead Free and the other isn't).

If you have the RL version you need to do some modifications in the PCB and you need to reflash the GAL.

[mattydr67]

One important question:

Is your cable based in the FTDI232BL or FTDI232RL?

(FTDI232BL and FTDI232BM are the same - BL is Lead Free and the other isn't).

If you have the RL version you need to do some modifications in the PCB and you need to reflash the GAL.

Do you have any good schematic for GAL programmer.
Thanks
Good luck

[KenshinPT]

Do you have any good schematic for GAL programmer.
Thanks
Good luck

Hey mate, check this out:

ELM - Simple GAL Programmer (http://elm-chan.org/works/pgal/report_e.html)

EEProm, PIC and GAL Programmer (http://home.planet.nl/~havinga1/programmer/programmer.htm)

Welcome to GALBlast (http://www.armory.com/~rstevew/Public/Pgmrs/GAL/_ClikMe1st.htm)

They are not that quickier to build... but I never found one simplier :(

[DiagService]

My cable is with FT232BL, Atmega162

[KenshinPT]

My cable is with FT232BL, Atmega162

Are you sure you're using the original VCDS 908.0 english with arash dumps?

And how about the fuses? Are they correct? Do you know which fuses you should write?

Are you using the last ponyprog or eXtreme Burner - AVR?

Is your car's battery less than 12V?

[xoom]

also need to check GAL and input transistors

[DiagService]

I have with UPA, Atmel 162 programmed
I have read Fuse bits and progremmed
Yes I have 12V in my Car,
I have vag old who works in the same Auto
When you more detail from Fuse Bits have can you send?

[KenshinPT]

I have with UPA, Atmel 162 programmed
I have read Fuse bits and progremmed
Yes I have 12V in my Car,
I have vag old who works in the same Auto
When you more detail from Fuse Bits have can you send?


Ponyprog:
http://img861.imageshack.us/img861/1063/configurationandsecurit.jpg




eXtreme Burner - AVR:
Low fuse: CD
High fuse: DC
Extended fuse: F9
Lock fuse: FF


Never, but never disable the SPIEN fuse... if you do that you need to erase the uC with HVPP.



Good luck

[makura]

Hi guys

i need help with pin code for passat 2005 model.here is the cluster picture.when i use my sbb *(clone) it says pin code unavilable.i have sbb,xprog-m,ad90 for tools.how ca i read the pin code using the above tools?
thanks in advance

[KenshinPT]

If you set the lock bits all active, do you think that VCDS software can erase the ATMEGA?

The lock bits just lock the reading capabilities, right? You'll be able to reflash it again via ISP?

Thanks.

[easyobd]

I have 2 interfaces with FT232BL inside, one of them after programming it with different dumps: 704, 805, 908, 10.6 says Interface not Found. Dumps 100% working tested on other interfaces and works fine but not with this cable, What could be wrong. STC chip and other components removed.
The second interface same as above after connecting it to computer is not recognize at all. I mean there is nothing in Device Manager, no Unknown Device or Serial nothing at all. After connecting it into USB port nothing happened, no sound that something was connected to computer no reaction at all. I change USB cable on interface but still to same, no idea what could be wrong?

[KenshinPT]

I have 2 interfaces with FT232BL inside, one of them after programming it with different dumps: 704, 805, 908, 10.6 says Interface not Found. Dumps 100% working tested on other interfaces and works fine but not with this cable, What could be wrong. STC chip and other components removed.
The second interface same as above after connecting it to computer is not recognize at all. I mean there is nothing in Device Manager, no Unknown Device or Serial nothing at all. After connecting it into USB port nothing happened, no sound that something was connected to computer no reaction at all. I change USB cable on interface but still to same, no idea what could be wrong?

Did you reflash the FTDI's EEPROM (24Cx6)?

[mishu_b]

...
for the first one - check the GAL / AFT device!

atb

[des2973]

Keep going people, this is awesome

[easyobd]

Did you reflash the FTDI's EEPROM (24Cx6)?

I didn't because one of my cables was recognize in device manager as Ross Tech, so I thought that there is no point. But what to do with the other cable which is not recognize at all. I can't see it in device manager, MProg, FtProg, etc.

[easyobd]

...
for the first one - check the GAL / AFT device!

atb

How to check it?