XPROG-T and BDM V1.0

[JotaB]

Hello everybody
I would like to Know if any one can upload the hex for the PIC of XPROG-T not Xprog. The diferences are that Xprog can't program HC(9)12D60 and Xprog T can.
And the BDM V1.5 that comes with XProg T does any one got this soft because my BDM V10 doesn't work with the schematic given. When he starts the led blink's twice. But in the BDM Pin and reset pin when I' try to read the HC12D60 nothing happen's. Can someone help me?
Did someone worked with this BDM and does everything worked?

thank's

[danyguit2000]

I've got Xprog-T as well,the schematic and bin for Tiny2313 that i have attached is the same as Xprog-T for 912b32 and 912d60 part only.
Xprog-T HC912xx part is based on AT Tiny2313, not on PIC.... !!!

[JotaB]

Thank's man but I already got that soft and hardware and it doesn't work and mine is exactly like yours. did you tested it with the hc12d60?

About Xprog-T I disagree with you because in the photo that I have of XPROG-T it only as PIC16F84(Just Take a look). Maybe someone as disassembled the code of tiny 2313 and converted it to PIC asm, because the pic as space left for it. In Xprog-t they use a PIC16F84A with XT at 8 Mhz

[danyguit2000]

On the bottom side of the PCB is full of componets and there you'll find the Tiny2313...
PIC 16C84 is only for the Xprog itself !!! Unscrew the middle nut and have look on the other side and you'll see i'm right.
Yes,works with hc912d60,but have to connect it as it shown on the manual...

[JotaB]

Hi,danyguit2000

Of Xprog-T the manual is the only thing that I've got, Don't have to unscrew it.
But what is screwing me is that I've got to read/write one HC12D60 for one airbag module and did make the hardware for BDM V1.0 and don't no if my problem is that hardware or the program BDM v10. So in manual of Xprog T they use BDM v1.5 do you have it for me to test it with the hardware of BDM v1.0

[danyguit2000]

Hello everybody
I would like to Know if any one can upload the hex for the PIC of XPROG-T not Xprog.

Just to clear the things up....
The Xprog-T is done by two parts:
The part that is done with PIC 16C84 is the Xprog
The other part is done with Tiny2313 for HC912B32 and HC912D60 only by using the dip switch...
Both parts is called Xprog-T
You have to do this schematic to be able to read 912B32 and 912D60



The bin file and the soft i have attached to my first reply to your post.
You have nothing to do with PIC 16C84 ...

[JotaB]

Hello again
Now everything is very clear for me but my problem is that I don't have BDM V1.5 or 2.0 (work on XP)that software comes with XPROG-T. Do you have it? Can you upload this please?

Thank's
JB

[sogaro]

I have Xprog-T from techgsm but need to read OF82B in Mercedes Plastic key but dont know how to connect wires. I recently got ETL 5E6 copier and it read chip, wrote on it but would not verify and it wont even read it again. Need help.

[danyguit2000]

This is the soft that came with Xprog-T.