Help Vw Golf 2007 1,4TSI How to read Micronas

[soxten]

I have some problem to read this Dash from Vw Golf 5 2007 1,4TSI Siemens/VDO
Dash OEM number is 1K0920874AX version Z02

I can connect to dash by obd with FVDI and do all normal stuff like read/clear.
But when I connect FVDI and do Dash CAN I can`t read info like immo,vin;CS it say to med "wrong version number" for dash....

So I connect Xprog to Micronas 3217G like pinout from Xprog but always get problem to bypass security.
I lift pin as pinout from Xprog, I check connection, I try 2 diffrent "00017" rev "B", I did connection as error_data.PDF with 4 wires but no reading......

I have a almost same Dash (diffrent version as Z02 and Z03) from Golf 5 2007 1,6TSI OEM number 1K0920874AX version Z03
And this I can read by FVDI V18 (not V21....) and I see PIN;VIN,MC etc.

Is some one expert on dash for Golf? please help me!

[soxten]

Please someone?


Christian Johansson via Iphone 5s

[koyot]

no one can help you if you do not have suitable equipment
maybe fly company can help

[soxten]

Is it only FLY (Avdi) as can read this dash?



Christian Johansson via Iphone 5s

[tunertool]

Try Smok JTAG for Micronas read.

[chriskross]

xprog can read this cluster 100%. Check connections

[soxten]

Chriskross, i spend 6h on xprog (clone 5.0) but don't work

Tunertool, i check Smoke JTAG


Christian Johansson via Iphone 5s

[soxten]

Chriskross, what pinout do you use?


Christian Johansson via Iphone 5s

[chriskross]

post board there are different.

[tuberider]

Hi Christian, i had problems as well reading Micronas . Please check :
lengh of cables 12-14cm
Test your 9917 adapter if all cables have contact (1A to 1B....)
Lift Oszi leg
Check with USB and Serial , connect 12V to Xprog .
Warm up Micronas if it still not work
Micronas can be an ass of a chip .....good luck !

[soxten]

Now it work

I use Xprog original + pictures from Xprog.
I lift 2pin as show in xprog pictures + reset pin!
If I don't lift reset pin I get some problem to read and write.
Use short cabels!
Twist as in pictures!

If I chose "dashboards" / VW / Golf V from 07-2006 i can change vin/pin/km/serialnumber

And I can read Micronas as singel under MCU / Micronas / CDC3217G secured






Christian Johansson via Iphone 5s

[autodigitec]

Very nice info, what is the version of your original xprog?

Also, with that cable and those connections, did you try 5.0 clone again?

[lupu_sandu]

Can you post micronas+eeprom please?

[soxten]

I have now try to do som changing to find pin

Pin is only in Eeprom
line 008A0 bit 13 to line 008E0 bit 8

ex pin 54321 is: E3 59 63 D58F 5F BB 5C 79 9A 3C 73 DC 67 E4 E7 A8 95 68 49
1C CE 9F 8F 51 E2 55 3B 6C 0B D1 D6 92 97 0E 79
40 C6 31 FD 1C CE 9F 8F 51 E2 55 3B 6C 0B D1 D6
92 97 0E 79 40 C6 31 FD



ex pin 12345 is: 65 97 D7 26
80 D8 BD E0 E6 17 30 B2 BF B6 DC 1A 53 B8 82 C9
2E 54 3C 5E D2 2C 55 8F FB A2 30 B2 BF B6 11 4E
D6 68 5A 29 2E 54 3C 5E D2 2C 55 8F FB A2 30 B2
BF B6 11 4E D6 68 5A 29

I cant see any changing in Micronas(?)

If some one find algho /how it is crypted, PLEASE write it here and help all of us!!!

[soxten]

Xprog Clone 5.0 work perfect 100% no problem.

And I use 1-002-0017 Rev.C 2009.04.06


Christian Johansson via Iphone 5s