FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386

**gas43** · 26th February, 2019, 03:10 PM

Maybe you don' t understand,
about pcb:
we change the bad components of china v54 pcb with better quality (components).

v48 is different pcb and it can' t be same with v54...

0475 is the firmware-software and cooperates flawlessly with v54 pcb.

photo v48 https://www.digital-kaos.co.uk/forum...8&d=1362161090
photo v54 http://www.digital-kaos.co.uk/forums...d=314864&stc=1

read here https://www.digital-kaos.co.uk/forum...tto-V54/page55

**joker01** · 26th February, 2019, 03:43 PM

ookk..the translator sometimes does not help me ....
anyway thanks for the photos at least I can recognize the pcb ... now I read that it should be done hw rework and downgrade to sw v53.

**gas43** · 26th February, 2019, 05:03 PM

v48 it's no longer on the market. only v54.

"simply" rework the components of v54 pcb (hw) and update the firmware from 0386 to 0475 if needed, because sοme sellers (ebay-aliexpress) have already the 0475.

of course we need and good luck with these china copies...

**joker01** · 26th February, 2019, 09:56 PM

ok thanks for the info ..... I'm downloading the fantomel archive of the first post ....... then I look for the list of components for rework hw

**joker01** · 26th February, 2019, 10:57 PM

I read the whole post, maybe I lost something ...... who helps me understand the steps .... ???
step 1 reflash mcu (lpc2000 or lpc2119)
step 2 if I want to upgrade to 0475 I open the folder "v54 fix etp" ..... these files how should I use them ???

**gas43** · 27th February, 2019, 08:20 AM

Originally Posted by joker01

I read the whole post, maybe I lost something ...... who helps me understand the steps .... ???
step 1 reflash mcu (lpc2000 or lpc2119)
step 2 if I want to upgrade to 0475 I open the folder "v54 fix etp" ..... these files how should I use them ???

I am waiting the converter usb to ttl and I will try to upgrade...

The fix .etp and .bin used after reflash hex 0475 with lpc...it use at the end, for the communication software 0475 with ftdi v54.
1 flash file .hex
2 unistall old drivers and then old software 0386
3 install software 0475 and new drivers
4 use the 2 fix tool ...

https://www.youtube.com/watch?v=YeP-W23UpeM

**joker01** · 27th February, 2019, 09:17 AM

I had seen that video .... but I did not understand the use of the 2 files ... I do not think he uses them .... however, I also wait for the converter then I try to break my cock .... hahahaah

**gas43** · 27th February, 2019, 09:40 AM

Originally Posted by joker01

I had seen that video .... but I did not understand the use of the 2 files ... I do not think he uses them .... however, I also wait for the converter then I try to break my cock .... hahahaah

Yes, he shows how use (time 7:12), mprog (ept) and then ftreadwrite (bin).

**reselie** · 27th February, 2019, 10:52 AM

Hi , did this a couple of days ago and tested the flasher with OK results (OBD).

First, you flash the .hex 0472 using the lpc Flash utility. Then using a TTL adapter (i used a FTDI ft232R) you write the epprom 0472 file configuration.
Then i used the 0472 eobd program with success. If you use FTDI adapter BE CAREFUL not to write eeprom file on the usb2ser adapter instead of Fgtech tool...

(Unplug the adapter before writing)

**carmageddon** · 27th February, 2019, 10:58 AM

Originally Posted by joker01

I read the whole post, maybe I lost something ...... who helps me understand the steps .... ???
step 1 reflash mcu (lpc2000 or lpc2119)
step 2 if I want to upgrade to 0475 I open the folder "v54 fix etp" ..... these files how should I use them ???

you need to change lpc soldered with new lpc2119, then you can do what you need

**gas43** · 27th February, 2019, 02:50 PM

Originally Posted by reselie

Hi , did this a couple of days ago and tested the flasher with OK results (OBD).

First, you flash the .hex 0472 using the lpc Flash utility. Then using a TTL adapter (i used a FTDI ft232R) you write the epprom 0472 file configuration.
Then i used the 0472 eobd program with success. If you use FTDI adapter BE CAREFUL not to write eeprom file on the usb2ser adapter instead of Fgtech tool...

(Unplug the adapter before writing)

I am confused...
Did you use ttl adapter to flash .hex and then the ftdi eeprom(.ept-bin)? with same ttl adapter?
How connect the wires for the write eeprom ftdi?
I think the eeprom (ftdi) can write-read from the existing socket of v54 to usb of pc...with mprog and ftreadwrite...
and use ttl adapter only for flash mcu-lpc (.hex).
I am wrong?

**joker01** · 27th February, 2019, 06:28 PM

[/COLOR]
[QUOTE = carmageddon; 3513114] you need to change lpc soldered with the new lpc2119, so you can do what you need [/ QUOTE]

I checked now .... I already have npx lpc2119, so the micro is ok just flash.
this photo are all the components to be replaced on the right ???
I have to put all those with the red lettering of fantomel ......

**reselie** · 27th February, 2019, 06:36 PM

Originally Posted by gas43

I am confused...
Did you use ttl adapter to flash .hex and then the ftdi eeprom(.ept-bin)? with same ttl adapter?
How connect the wires for the write eeprom ftdi?
I think the eeprom (ftdi) can write-read from the existing socket of v54 to usb of pc...with mprog and ftreadwrite...
and use ttl adapter only for flash mcu-lpc (.hex).
I am wrong?

Hi, i used ttl adapter to flash .hex. Then i forgot to disconnect from computer and when i used Mprog(or ftreadwrite - cant recall) i ended up with a TTL adapter that shows up as "FGTECH" on windows

**gas43** · 27th February, 2019, 06:44 PM

Originally Posted by joker01

[/COLOR]
[QUOTE = carmageddon; 3513114] you need to change lpc soldered with the new lpc2119, so you can do what you need [/ QUOTE]

I checked now .... I already have npx lpc2119, so the micro is ok just flash.
this photo are all the components to be replaced on the right ???
I have to put all those with the red lettering of fantomel ......

https://www.digital-kaos.co.uk/forum...tto-V54/page61