If I have uploaded several images but all the ones that boot no works the tuners
The list of channels is updated to March 2017 could be problem of this when starting?
Writing vfd
!!!!! UNC read error occurred while reading from NAND flash
If I have uploaded several images but all the ones that boot no works the tuners
The list of channels is updated to March 2017 could be problem of this when starting?
Writing vfd
!!!!! UNC read error occurred while reading from NAND flash
Do you have a hdd inside and did you not back up image before you flashed do you know what image was on the box before hand? Is it a v2 clone?
Sounds like a bootloader error as shaunfree was saying.
Last edited by DOUGALMCD; 22nd March, 2017 at 08:11 PM.
thanks for answering
Is a clone v2
I have no idea what image I had previously
Hdd does not have
I think it's a boot problem, I think?
So you flashed bootloader and restarted box?
You then formatted usb to fat 32 and put unzipped file called vuplus on it and reflashed from front of box without any other usb connected?
No joy?
Issue may be related to wrong bootloader or software or the security chip may need replaced. This relates to bad address in epc meaning it can't read it or software is wrong or it has failed.
You could check the voltage that comes from the chip but I wouldn't advise that if you are not competent in electronic diagnosis.
thank you very much
I checked the output voltages of the power supply and they are correct
The famous capacitors are changed
And the voltage of the security chip is also checked and is ok
What could it be??
Have you tried flashing this image on
BlackHole-2.0.7-bm750_usb_Ferrari_V2
You might need to put the "boot_cfe_auto.jffs2" file in the Duo folder with the other 2 files that are in thereCode:https://mega.nz/#!4ggkGYSK!wAJBucDmFNRJjehhFHBomz8hGaRXkhLW0ETj7JpjrhI
Last edited by Fergal; 23rd March, 2017 at 11:20 PM.
Obviously if you've checked voltages changed capacitors etc you are competent enough to get the box working.
Can you specify exactly what you have repaired on the box capacitors etc which ones and where?
Can you tell us when you load an image that starts what satellite you are on and what the signal strength is and also post the configuration of the tuners?
What image is starting? What channel list you are using?
Have you tried each tuner individually?
Can you post the voltages from the ic security chip?
If at all possible post a few pictures of problems.
Can still see it being security chip if tuners not working.
Thanks
Last edited by DOUGALMCD; 24th March, 2017 at 02:08 PM.
Ok I have flashed it as you said and it stays the same thanks
Last edited by malpi; 26th March, 2017 at 10:50 AM.
The capacitors change c 807 c 814 c850 c848
The signal strength puts 99%
Voltage tuner 13v but without signal
Image blchole and openspa
You pass image security chip security477-16c9895f4ca15fed4504355435d1a892.jpg
Hi your box loads up and you have a great signal but it wont let you access tuners everything points towards the security chip being faulty.
Ok, thank you so much
Do you know if there is a way to buy?
No but I'm sure someone will have one lying around spare.
It's solved thank you very much to all
Solution = V2 upd_vu62k load the file po rs 232 and everything ok 100%
Hi Malpi, I have had success with 1 of these with the same problem. PSU fix.
Let me know if I can help.
Regards,
Jules.
The problem wasn't with screen starting as the thread suggested the problem lay within a faulty security chip which the v2 clone model has he has now sorted the chip as the post above mentions.
Bookmarks