Digiprog 3 corrupting files (frozen mileage)

**kur715** · 10th October, 2020, 02:33 AM

Hi , can someone please school me , my digiprog 3 has now decided to corrupt any thing I program, now x2 dashes frozen , both 93xx series eeproms , can I erase the eeprom and try to program again? I have a new digiprog 3 unit now but wanted to check here first,

Thank you.

**jomberykaso** · 10th October, 2020, 04:30 AM

What car are you talking about?, maybe your clip are damaged or Digiprog green adapter is damaged.

**kur715** · 10th October, 2020, 07:21 AM

I have have this problem on toyota hilux 93C66 and also on isuzu d-max , have been able to do the hilux many times with same clip , changed clip still frozen dash on both vehicles , if I erase can the digiprog 3 make a new healthy program? Or does it not work that way?

**brend** · 10th October, 2020, 08:07 AM

For safe job always need save original ,so......for eeprom by better simpel eep programmer.

Originally Posted by kur715

I have have this problem on toyota hilux 93C66 and also on isuzu d-max , have been able to do the hilux many times with same clip , changed clip still frozen dash on both vehicles , if I erase can the digiprog 3 make a new healthy program? Or does it not work that way?

**kur715** · 10th October, 2020, 09:10 AM

Hi , i do have a EZP2010 unit , will that be ok? , but i need calc software to use it though?

**jomberykaso** · 10th October, 2020, 10:37 AM

Originally Posted by kur715

Hi , i do have a EZP2010 unit , will that be ok? , but i need calc software to use it though?

Yes..........................

**Cllau** · 10th October, 2020, 10:59 AM

Originally Posted by kur715

Hi , can someone please school me , my digiprog 3 has now decided to corrupt any thing I program, now x2 dashes frozen , both 93xx series eeproms , can I erase the eeprom and try to program again? I have a new digiprog 3 unit now but wanted to check here first,

Thank you.

.................................................. .......................................

mate your problem is not Digiprog3, problem is your poor pin connection on reading.You must recognise a correct reading and verify also with your tool and visual inspecting . Compare your bad read dumps for Denso Eg: on the first 00 line it has to start with 80FF 80FF, usually when is a bad pin connection digiprog3 will show you numbers Eg: 2F46, ADF3 whatever numbers you get there in instead of 80FF, it means that you have a poor pin connection, then the complements of 0000 FFFF will get wrong calculated by your Digiprog3 tool and will result in freezing Mileage....

**kur715** · 10th October, 2020, 12:21 PM

Oh I see , I'm still learning all this you see , i threw away the old blue test clip for a nicer 3M one , worked a charm up until now , is it possible to modify the dump on the digiprog 3 or will I have to use a different method to "unfreeze" it? Also what actually causes it to freeze is there something not right with the checksum ? Byte swapping?

**kur715** · 10th October, 2020, 01:04 PM

Ok so this is what im dealing with , does this look right? have i read the chip correctly "93C66" or what do i need to change? 20201011_004629.jpg 20201011_004439.jpg

**SEAT.** · 10th October, 2020, 01:34 PM

set the cs in relearn mode

**kur715** · 10th October, 2020, 01:52 PM

Originally Posted by SEAT.

set the cs in relearn mode

Please elaborate? I'm not familiar with this

**Cllau** · 10th October, 2020, 04:48 PM

Originally Posted by kur715

Ok so this is what im dealing with , does this look right? have i read the chip correctly "93C66" or what do i need to change? 20201011_004629.jpg

20201011_004439.jpg

you forgot to mention from what car and year is this read off and mileage??

....ori mileage is 242556km